Sanyo VCC-4324 - Manuals - manualsarea.com

Page 4 - INFORMATION TO USER; Safety Guard; For the customers in Canada

INFORMATION TO USER Safety Guard THIS SYMBOL INDICATES THAT THERE AREIMPORTANT OPERATING AND MAINTENANCEINSTRUCTIONS IN THE LITERATURE ACCOMPANYINGTHIS UNIT. WARNING: TO PREVENT THE RISK OF FIRE OR ELECTRIC SHOCK , DO NOTEXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. This installation should be made by ...

Page 5 - PRECAUTIONS

PRECAUTIONS In case of problem Do not use the camera if smoke or a strange odour comes from theunit, or if it seems not to function correctly. Disconnect the powercord immediately, and consult your dealer (or a Sanyo AuthorizedService Centre). Do not open or modify Do not open the cabinet, as it may...

Page 6 - PARTS NAMES

PARTS NAMES 1 Lens iris output connector (4 pin) This 4-pin connector is used to send the DC control signal and power supply to an auto-iris type lens. 2 Flange-back adjustment lever (See page 7) 3 Flange-back lock screw 4 Lens mount cap The cap is installed to protect the lens mount section. Remove...

Page 9 - Flange-back adjustment

PARTS NAMES Flange-back adjustment If the pick-up surface is not correctly positioned with relation to the lens focal point, the picture will be out offocus (in particular when using auto-iris power zoom lenses, sold separately). If that is the case, adjust theflange-back position as described below...

Page 10 - MOUNTING THE LENS; Installation of a VIDEO type auto-iris lens (sold separately)

MOUNTING THE LENS Check the lens mount Do not use a lens if the length “ L ” is more than 5 mm. That may damage the camera and prevent proper installation. Installation of a DC type auto-iris lens (sold separately) A 1/3 inch CS mount type lens without EE amplifier circuit that only uses a DC power ...

Page 12 - CONNECTIONS; Basic connection for monitoring or recording

CONNECTIONS Basic connection for monitoring or recording The peripheral devices (VCR, monitor, lens, etc.) and cables are sold separately. 1 Make the video signal connection between the camera and the monitor or time lapse VCR. 2 Insert the plug of this power cord into a wall outlet.The POWER indica...

Page 13 - SETTINGS; Line phase adjustment

SETTINGS Line phase adjustment When using a camera switcher to connect 2 cameras or more to onemonitor, there may be a vertical roll of the images when switched. Insuch a case, set as described below. 1 Set the SYNC switch to the L-L position. 2 Switch the display on the monitor from camera 1 to cam...

Page 14 - Lens iris adjustment; Backlight compensation setting

SETTINGS Lens iris adjustment If using a DC type auto-iris lens, you will need to set the LEVEL (VR301) volume when shooting in the conditions described below. L (counterclockwise): To decrease the contrast H (clockwise): To increase the contrast • If shooting simultaneously in a dark room and throu...

Page 15 - Electronic iris function setting

SETTINGS Electronic iris function setting Use a manual or fixed iris lens and set the lens aperture to theshortest F stop. Set the EI/BLC switch to the EI-ON position. Note: Please refer to the specifications for dynamic range of the electroniciris. CAUTION: • The electronic iris is suitable for nor...

Page 16 - TROUBLESHOOTING; SERVICE

SETTINGS C • B/W (color/black and white) switch setting This switch lets you select the timing of the automatic switching ofthe optical filter to color image or black and white image, accordingto the subject brightness. The default setting is “ L ”. Set the switch according to the brightness. (Fig. ...

Page 17 - SPECIFICATIONS

SPECIFICATIONS Camera: Scanning system : NTSC standard TV system (525 TVlines, 30 frames/sec.) Interlace : PLL 2:1 interlace Image device : 1/3 inch solid state image deviceCCD Picture elements : 537 (H) x 505 (V) Effective picture elements : 510 (H) x 492 (V) Synchronizing system : Internal sync, L...