Samsung 510N - Manuals - manualsarea.com

Page 6 - Bottom; Tripod Mounting Hole; Front; Tripod Mounting Bracket Screw Hole.

Bottom www .samsungcctv .com Tripod Mounting Hole Used to install the camera on an optional tripod. The tripod must be equipped with the screw specified as shown below. 1/4"-20 UNC (20 THREAD) L:4.5mm±0.2mm (ISO standard), or 0.197" (ASA standard) L G G E ET TT TIIN NG G T TO O K K N NO OW W...

Page 7 - Accessories; Back; Menu Setup Buttons; SET Button; Used to connect a remote plug.

Video Out Jack Used to connect an externalvideo monitor in jack. Power Terminal Used to connect AC24V or DC12V power source. Instruction Manual Accessories Auto Iris Lens Plug Remote Plug C-Mount Adapter L-Wrench Back Menu Setup Buttons SET Button Used to access menu mode. Also used to confirm the s...

Page 8 - Peel approximately 8mm from the end of the lens cable outer cover.; Remove the protective cap, and attach the lens to the camera by; Notes; Set the DC/VIDEO selection switch to DC or VIDEO according to the

Lens The lens is not supplied with this camera. Purchase a lenssuitable for your environment. This camera accepts the autoiris lens and both C- and CS-mount lens. If the lens is marked with fingerprints or other marks, the imagequality might be poor. It is recommended to use a high quality lens to i...

Page 9 - Attach the C Mount lens adapter by turning clockwise.; be occurred hunting.

M ounting a CS-mount lens After removing the protecting cap, attach the lens intothe camera by turning clockwise. Mounting a C-mount lens 1. Attach the C Mount lens adapter by turning clockwise. 2. Attach the lens to the camera by turning clockwise. A heavy lens may disturb the balance with the came...

Page 10 - Connecting to Monitor; Connect the VIDEO Out jack to the monitor VIDEO In jack.; Connecting to Power; • As the connecting method varies with the instruments,

Connecting to Monitor Connect the VIDEO Out jack to the monitor VIDEO In jack. Connecting to Power • As the connecting method varies with the instruments, refer to the manual supplied with the instrument. • If necessary, you can connect the monitor to the REMOTE jack on the back of your camera. For ...

Page 11 - Setup Menu; END

Setup Menu Camera ID (see page 23) • ON : Activate. You can enter up to 14 alphanumeric characters and selectthe ID position. • OFF : Deactivate Backlight (see page 26) •ON : Backlight Compensation. •OFF : Deactivate. Motion Detection (see page 27) • ON : Activate. • OFF : Deactivate Lens Selection ...

Page 12 - Camera ID

Use the five Setup Menu buttons on the rear of the camera. 1. Press the SET button to access the setup mode. Setup menu is displayed on the monitor screen. LEFT button UP button SET button RIGHT button DOWN button S e t u p C a m e r a I D O F F B a c k l i g h t O F FM o t i o n D e t e c t . O F F...

Page 13 - The alphanumeric letters are displayed.

3. Press SET button. The ID generation screen appears. 4. The alphanumeric letters are displayed. You can enter up to 14 characters. Move the cursor to the desired character by using the 4-directional buttons. The selected character blinks andappears in the bottom of the screen. Press the SET button...

Page 14 - Press the SET button to display the setup menu and move the arrow; You can select the weight from 0 to 4.

Motion Detection Your camera transmits an alert signal when it detectsmotion of an object on the screen. If you connect the camerato an external alarm, you can pay attention to the screenwhen the alarm sounds. This feature is useful when youhave to monitor several screens simultaneously. Backlight 1...

Page 15 - How to Assign the Zone

4. Specify the zone area. You can point to the top, bottom, left, and right base lines bysetting a proper value from 0 to 15 with an increment of 1. Move the arrow indicator to 'Top' using the UP or DOWNbutton and increase or decrease the value using the LEFT orRIGHT button. Repeat the procedure for...

Page 16 - Tips on Using the Motion Detection Feature; Lens Selection; Hint

6. When completed, move the arrow indicator to 'End' and press the SET button. Tips on Using the Motion Detection Feature • After selecting zone and sensitivity, perform a test operation to make sure it works properly. • If the lighting flickers, the motion detection feature might not work properly....

Page 17 - Shutter Speed Control; If the camera directly faces strong fluorescent light in 'ESC' mode,; NTSC Models

4. When completed, press the SET button. 3. If you choose “DC”, you can adjust the brightness. After pressing the SET button, adjust the brightness of the monitorscreen using the LEFT or RIGHT button. The screen becomes darker when the value is decreased andbrighter when the value is increased. You ...

Page 18 - Gain Control; White Balance Control

Gain Control 1. Press the SET button to display the setup menu and move the arrow indicator to 'Gain' using the UP or DOWN button. 2. Select 'AGC' or 'OFF' using the LEFT or RIGHT button. AGC : Activates automatic gain control feature.OFF : Deactivates automatic gain control feature. If you choose ‘...

Page 19 - Synchronization Mode

Synchronization Mode Two synchronization modes are available Internal andExternal linelock. -In linelock mode, it synchronizes the videosignal between cameras without a synchronous generator. The linelock synchronization is only used in the areas of60Hz(NTSC Models)/50Hz(PAL Models). 1. Press the SE...

Page 20 - Reset

If you connect a remote plug to the REMOTE jack on therear of the camera as shown below, you can access themenu setup mode from a remote place. You must turn the camera power off when you connect or removethe remote plug. NOTE NOTE The phase is preset to 225 degrees at the factory. You can re- adjus...

Page 22 - DECLARATION OF CONFORMITY

DECLARATION OF CONFORMITY Application of Council Directive(s) 89/336/EEC Manufacturer's Name SAMSUNG TECHWIN CO., LTD Manufacturer's Address SAMSUNG TECHWIN CO., LTD 42, SUNGJU-DONG CHANGWON-CITY, KYUNGNAM, KOREA, 641-120 European Representative Name European Representative Address Equipment Type/En...