Samsung 510N - Manual

M ounting a CS-mount lens After removing the protecting cap, attach the lens intothe camera by turning clockwise. Mounting a C-mount lens 1. Attach the C Mount lens adapter by turning clockwise. 2. Attach the lens to the camera by turning clockwise. A heavy lens may disturb the balance with the came...

Connecting to Monitor Connect the VIDEO Out jack to the monitor VIDEO In jack. Connecting to Power • As the connecting method varies with the instruments, refer to the manual supplied with the instrument. • If necessary, you can connect the monitor to the REMOTE jack on the back of your camera. For ...

Setup Menu Camera ID (see page 23) • ON : Activate. You can enter up to 14 alphanumeric characters and selectthe ID position. • OFF : Deactivate Backlight (see page 26) •ON : Backlight Compensation. •OFF : Deactivate. Motion Detection (see page 27) • ON : Activate. • OFF : Deactivate Lens Selection ...

Use the five Setup Menu buttons on the rear of the camera. 1. Press the SET button to access the setup mode. Setup menu is displayed on the monitor screen. LEFT button UP button SET button RIGHT button DOWN button S e t u p C a m e r a I D O F F B a c k l i g h t O F FM o t i o n D e t e c t . O F F...

3. Press SET button. The ID generation screen appears. 4. The alphanumeric letters are displayed. You can enter up to 14 characters. Move the cursor to the desired character by using the 4-directional buttons. The selected character blinks andappears in the bottom of the screen. Press the SET button...

Motion Detection Your camera transmits an alert signal when it detectsmotion of an object on the screen. If you connect the camerato an external alarm, you can pay attention to the screenwhen the alarm sounds. This feature is useful when youhave to monitor several screens simultaneously. Backlight 1...

4. Specify the zone area. You can point to the top, bottom, left, and right base lines bysetting a proper value from 0 to 15 with an increment of 1. Move the arrow indicator to 'Top' using the UP or DOWNbutton and increase or decrease the value using the LEFT orRIGHT button. Repeat the procedure for...

6. When completed, move the arrow indicator to 'End' and press the SET button. Tips on Using the Motion Detection Feature • After selecting zone and sensitivity, perform a test operation to make sure it works properly. • If the lighting flickers, the motion detection feature might not work properly....

4. When completed, press the SET button. 3. If you choose “DC”, you can adjust the brightness. After pressing the SET button, adjust the brightness of the monitorscreen using the LEFT or RIGHT button. The screen becomes darker when the value is decreased andbrighter when the value is increased. You ...

Gain Control 1. Press the SET button to display the setup menu and move the arrow indicator to 'Gain' using the UP or DOWN button. 2. Select 'AGC' or 'OFF' using the LEFT or RIGHT button. AGC : Activates automatic gain control feature.OFF : Deactivates automatic gain control feature. If you choose ‘...

Synchronization Mode Two synchronization modes are available Internal andExternal linelock. -In linelock mode, it synchronizes the videosignal between cameras without a synchronous generator. The linelock synchronization is only used in the areas of60Hz(NTSC Models)/50Hz(PAL Models). 1. Press the SE...

If you connect a remote plug to the REMOTE jack on therear of the camera as shown below, you can access themenu setup mode from a remote place. You must turn the camera power off when you connect or removethe remote plug. NOTE NOTE The phase is preset to 225 degrees at the factory. You can re- adjus...

DECLARATION OF CONFORMITY Application of Council Directive(s) 89/336/EEC Manufacturer's Name SAMSUNG TECHWIN CO., LTD Manufacturer's Address SAMSUNG TECHWIN CO., LTD 42, SUNGJU-DONG CHANGWON-CITY, KYUNGNAM, KOREA, 641-120 European Representative Name European Representative Address Equipment Type/En...