Rotel RHB-200 - Manuals - manualsarea.com

Page 3 - Connecting Keypads

3 LIGHT LIGHT DC 12V CLONE IN ZONE1 IN ZONE3 IN ZONE4 IN ZONE2 IN IR OUT ZONE3 ZONE4 ZONE1 COMMON IR OUT ZONE2 TUN CD MUTE MP3 OFF AV V V ZONE OUT ZONE IN TUN CD MUTE MP3 OFF AV V V ZONE OUT ZONE IN TUN CD MUTE MP3 OFF AV V V ZONE OUT ZONE IN TUN CD MUTE MP3 OFF AV V V ZONE OUT ZONE IN TUN CD MUTE M...

Page 6 - Contents

6 RKP-200/RHB-200 Contents 1. RKP-200 Keypad 2 2. RHB-200 Connecting Hub 2 3. Connecting Keypads 3 4. Connecting RHB-200 4 5. Clone setup 5 Introduction .............................................................. 7 Key Features 7 RKP-200 Overview .....................................................

Page 7 - Introduction

7 Introduction The RKP-200 Keypad and RHB-200 Connecting Hub provide an integrated system that allows con- trol of Rotel multi-zone systems from wall mounted keypads in remote zones. Key Features • Programmed to operate Rotel multi-zone receiv- ers, DVD players, CD players, and AM/FM tuners. • Learn...

Page 8 - Connecting the system; See Figure 3

8 RKP-200/RHB-200 +12V DC input The power connector receives +12V signal when AC power supply is plugged into a wall outlet. Clone Input R J-45 modular jack accepts CAT-5 cable from keypad during cloning conﬁguration. Zone Inputs Four RJ-45 modular jacks accept CAT-5 cables from keypads in up to fou...

Page 10 - Operating the Keypads; Selecting a component; If you choose to customize the keypads,; Operating a CD Player

10 RKP-200/RHB-200 Operating the Keypads The keypads are preprogrammed to operate the Rotel RX-1052 multi-zone receiver and the follow- ing source components: Rotel CD Players: RCD-1072 & RCC-1055 Rotel Tuner: RX-1052 built-in tuner Rotel DVD Player: RDV-1092/RDV-1060 MP3 Players: Navipod and th...

Page 11 - Backlighting; IR Sensor; Configuring the keypads; Using the DIP switches

11 Backlighting As delivered from the factory, the keypads have automatic backlighting for the device buttons and the button. When a device button is pressed, the backlighting for that button remains lit to indicate the currently selected device.The backlighting for the button remains on when the so...

Page 12 - Disabling IR Sensor; Optional Device Buttons

12 RKP-200/RHB-200 NOTE : Flashing button illumination provides conﬁr- mation and error indications during the Learning and SMART sequence programming. The back- lighting should be enabled during conﬁguration. Disabling IR Sensor An IR sensor on the front of the keypad allows operation of the system...

Page 15 - Programming a SMART Sequence

15 4. Within 30 seconds, press the keypad command button that you wish to learn (in this example, the button). The backlighting on the button turns on and the keypad is ready to receive the IR code. It will ﬂash six times if an improper button is pressed (for example, a device button that cannot be ...

Page 16 - Cloning; Keypads in the remote zones must not be in; Resetting keypads

16 RKP-200/RHB-200 Programming a SMART Sequence with Invisible Layer Commands To include invisible layer commands in a SMART sequence, substitute the following steps for Step 4 in the preceding instructions:• Put SW1, SW2, SW3, or SW4 in the ON posi- tion to select the invisible layer where the de- ...