Robertshaw 9615 - Manuals - manualsarea.com

Page 2 - TABLE 1

Features • Four pre-programmed Energy Star setpoints for each day of the week • Quickset™ programming for quickly programming all days of the week simultaneously • Energy Efficient Recovery (EER™) • Residual cooling for added air-conditioning efficiency • Two “AA” ENERGIZER brand batteries retain pr...

Page 3 - FIGURE 1; Installing Item 9615 Thermostat; NOTE; OFF; Turn power off to the heating and cooling systems.

FIGURE 1 Installing Item 9615 Thermostat NOTE : F OR NEW INSTALLATIONS , MOUNT THERMOSTAT ON INSIDE WALL , 4-5 FEET ABOVE THE FLOOR . D O NOT INSTALL BEHIND A DOOR , IN A CORNER , NEAR AIR VENTS , IN DIRECT SUNLIGHT , OR NEAR ANY HEAT OR STEAM GENERATING FIX - TURES . I NSTALLATION AT THESE PLACES W...

Page 4 - FIGURE 3; NOTE: Enclosed plastic; Align base with plastic anchors and feed wires through opening.; MOUNTING HOLES; OPENING

FIGURE 3 7. Drill the marked holes using a 3/16" drill bit. NOTE: Enclosed plastic anchors do not require a drilled hole for drywall. 8. Tap plastic anchors into the holes. 9. Align base with plastic anchors and feed wires through opening. See Fig 4. FIGURE 4 10. Secure base to wall with supplie...

Page 5 - Programming Guide

Programming Guide Set Time of Day, Day of Week,Temperature Differential,Residual Cooling 1. Press SET & PROG/MAN. Release simultaneously. Press or to change Time of Day. 2. Press Press To Change Day of Week 3. Press Press To change 1st Stage Temperature Differential NOTE: T HE T EMPERATURE D IFF...

Page 7 - Begin Programmed Operation

4. Press SET. 5. Press or to change MORN temperature. 6. Repeat Steps 2-5 for DAY, EVE, and NITE. 7. Repeat steps 2–6 above to program any other day of the week. 8. Shift COOL-OFF-HEAT to HEAT position. 9. Repeat steps 2-6 to program HEAT (winter) settings. Begin Programmed Operation 1. Place AUTO/O...

Page 9 - To Test Thermostat; switch into the COOL position.; LED Indicator

To Test Thermostat WARNING: DO NOT SHORT (JUMPER) ACROSS TERMINALS OF GAS VALVE OR SYSTEM CONTROL TO TEST OPERATION. THIS WILL DAMAGE THE THERMOSTAT AND VOID YOUR WARRANTY. CAUTION: D O NOT SWITCH SYSTEM TO COOL IF THE TEMPERATURE IS BELOW 50°F (10°C). T HIS CAN DAMAGE THE AIR CONDITIONING SYSTEM AN...

Page 10 - Troubleshooting; SYMPTOM REMEDY; If problems with thermostats cannot be solved, call:; Uni-Line North America; Warranty Claims Department

Troubleshooting SYMPTOM REMEDY 10 Thermostat does not turn on system. Check Wiring.(See “INSTALLATION.”) Check fuse. Replace with 3 ampfuse if fuse has opened. Fiveminute compressor short cycleprotection may be in effect. PressRESET to override. NOTE: This willerase programming. Thermostat turns on ...

Page 11 - Wiring Diagrams; Robertshaw 9615 Multi-Stage Thermostat

11 Wiring Diagrams The following is just a sample of the most common types of HVAC sys-tems. Refer to your system’s installation manual for wiring information. Robertshaw 9615 Multi-Stage Thermostat C R Y2 Y1 W1 G W2 O B C R Y/Y1 W1 G W2 2 Stage Heat / 1 Stage Cool Robertshaw 9615 Multi-Stage Thermo...

Page 12 - Five-Year Limited Warranty

Five-Year Limited Warranty Maple Chase Company warrants to the original contractor installer, or to the original consumer user, each new Robertshaw thermostat to be free from defects in materials and workmanship under normal use and service for a periodof five (5) years from date of purchase. This w...