Rinnai FM10LA - Manuals

Rinnai 5 HW_GI_FM10 OIM IMPORTANT MANDATORY INSPECTION PRIOR TO INSTALLATION Immediately report any damage or discrepancies to the Supplier of the appliance. This appliance was inspected and tested at the time of manufacture and packaging, and released for transportation without known damage. Upon r...

Rinnai 6 HW_GI_FM10 OIM FEATURES & BENEFITS Congratulations on purchasing the Rinnai Gas Instantaneous water heater. • The appliance is compact, saving both wall and floor space. • The burner lights automatically when the hot water tap is opened, and goes out when the tap is closed. IGNITION IS ...

Rinnai 7 HW_GI_FM10 OIM TO OPERATE The opening of any hot water tap will automatically start the appliance. Once water is flowing through the appliance the burner will be ignited by electronic ignition via the electronic ignition and control module. When the hot water tap is closed and water flow th...

Rinnai 8 HW_GI_FM10 OIM WATER FLOW AND TEMPERATURE ADJUSTMENT Water fixtures with a rated water flow rate of 7.5 litres per minute or higher are recommended.A water flow adjustment lever is fitted to adjust the maximum water flow from the appliance. Such adjustment may be useful to compensate for se...

Rinnai 9 HW_GI_FM10 OIM FAULT FINDING Problem Fault Solution Burner does not ignite, or is difficult to ignite No gas supply Check gas is turned on at water heater and gas meter or cylinder Low battery power Replace battery Other Service Call Pilot lights but no main burner Low water pressure Check ...

Rinnai 10 HW_GI_FM10 OIM This page is intentionally blank

Rinnai 11 HW_GI_FM10 OIM Operation Table of Contents 3 General Installation Information 12 Regulations ........................................................................................................................................................................ 12Applicable Models ...........

Rinnai 12 HW_GI_FM10 OIM NOTE Installation, service and removal MUST BE by an appropriately licensed tradesperson ONLY . It is the installer’s responsibility to ensure all current AS/NZS 5601 requirements are met. Remove transit protection. Check for damage, if any is found DO NOT install and contac...

Rinnai 13 HW_GI_FM10 OIM WATER SUPPLY See "Table 1. Appliance Specifications" on page 18, for applicable water pressures. Approved pressure limiting valves may be required if the 'Maximum' rated water supply pressures in Table 1 are exceeded. To achieve the rated flow, the 'Minimum' water su...

Rinnai 14 HW_GI_FM10 OIM APPLIANCE MOUNTING METHOD 1. After determining the desired location for the water heater, use the dimensions in the drawing right to measure and mark off the positions of the 3 appliance mounting points A and the 4 heat shield mounting points B . 2. Install 3 suitable screws...

Rinnai 15 HW_GI_FM10 OIM APPLIANCE FLUE TERMINAL R e f . e f . M i n c l e a r a n c e s m m Natural draught a B e l o w e a v e s , b a l c o n i e s a n d o t h e r p r o j e c t i o n s : F o r a p p l i a n c e s u p t o 5 0 M J / h i n p u t 3 0 0 F o r a p p l i a n c e s o v e r 5 0 M J / h i...

Rinnai 16 HW_GI_FM10 OIM TESTING 1. Before final connection of the water heater purge gas, hot water and cold water supply lines. Swarf in either the gas or water supplies may cause damage or malfunction which is not covered by warranty. 2. See Table 1 for connection size, water and gas pressure spe...

Rinnai 17 HW_GI_FM10 OIM COMMISSIONING CHECK LIST A commissioning check list is provided on the appliance front cover to enable the installer to step through the correct commissioning procedure when installing a Rinnai water heater. The check list can also assist the installer to identify potential ...

Rinnai 18 HW_GI_FM10 OIM Table 1. Appliance Specifications Model Water Supply kPa Weight kg Fittings Minimum Inlet Water Pressure For 10L/min. Minimum Inlet Water Pressure For Operation Maximum Inlet Water Pressure Hot & Cold Water Natural Gas Propane Gas FM10 120 40 1000 14 R 1/2” BSP Male R 1/...

Rinnai 19 HW_GI_FM10 OIM Figure 4. Dimensions Approximately 175 to base of fittings 61 51 575 170 838 425 48 380 205 201219 380 120 120 120 120 70 70 70 51 Location of upper rear mounting holes Location of lower rear mounting hole APPLIANCE DIMENSIONS

Rinnai 20 HW_GI_FM10 OIM Solenoid Valve 1 Solenoid Valve 2 High Voltage Lead (Ignition) Flame Rod Temperature Overheat Switch (Self-resetting) Modulation Motor Thermistor (Heated water outlet temperature) Micro-switch SV1 SV2 HV FR TTB M NTC SW MAIN MICROPROCESSOR TEMPERATURE CONTROL MICROPROCESSOR ...

Rinnai Australia Pty Ltd ABN 74 005 138 769 | AU24752 100 Atlantic Drive, Keysborough, Victoria 3173P.O. Box 460, Braeside, Victoria 3195Tel: (03) 9271 6625Fax: (03) 9271 6622 National Help Line Tel: 1300 555 545* Fax: 1300 555 655 Monday to Friday, 8.00 am to 5.00 pm EST. After Hours Hot Water Serv...