Revolabs 03-hdvenueu - Manuals

- 6 - Introduction Congratulations on your purchase of a Revolabs Wireless Microphone System! This system utilizes 1.9 GHz DECT technology, and high band-width audio from multiple wireless microphones, enabling clear, reliable, un-tethered communications in recording, audio/video conferencing, speec...

- 7 -  Acoustic echo cancellation (AEC)  Feedback elimination  Level control  Equalization  Noise cancellation The system is designed to optimize audio capture/reproduction by providing:  Consistent audio input from all participants  Minimum room noise  Mute control  Wireless encryption  A...

- 8 - Revolabs HD Venue™ Base Station Connections The Revolabs HD Venue ™ Base Station, shown below in front and rear panel views, manages wireless audio signal processing, pairing, and muting between the Revolabs microphones and the Base Station. Front View Rear View Controls and Connections: 1. Ch...

- 9 - Revolabs HD Venue ™ Base Station Audio Connections There are two 3.5mm balanced inputs (either ¼‖ or XLR) and two 3.5mm balanced outputs (either ¼‖ or XLR) on the back panel of the unit providing access to each channel‘s audio signal. ¼‖ jacks are configured as follows: Tip positive Ring negat...

- 10 - 1 2 3 4 5 6 7 8 on off Using the Rear Panel Configuration DIP Switches DIP Switch Feature Off (Default) On 1 Output Mixing Individual Outputs Mixed Output 2 Low Pass Filter No LPF LPF 3 Audio Output Level Line Level Mic Level 4 Mute Mode Individual Mutes No Mutes 5 Sharing Mode All frequencie...

- 11 - DIP Switch 5&6 – Sharing Mode: To use two HD Venue Systems in the same area, both systems must have DIP Switch 5 set to ON. One of the HD Venue Systems must have DIP Switch 6 set to ON (A frequencies) and the other HD Venue System must have DIP Switch 6 set to OFF (B frequencies). DIP Swi...

- 12 - Mics Unmute at Startup: By default the mics go into a muted state when they are removed from the charger. Thi s is done to prevent handling noise as the microphone is placed into position. By selecting ‗Mics Unmuted at Startup‘, the mics will go into an unmuted state when removed from the cha...

- 13 - Battery: This provides the current battery level for the microphone that is paired to each channel and active. The value changes in 12.5% increments and represents the bottom of the range the battery is in. Therefore a value of 87% means that the battery level is between 87%-100%. Pairing: Th...

- 14 - 1. Earpiece jack — accepts the 2.5mm plug for the earpiece. 2. Charging port — docks to Revolabs HD Charger Bases. 3. Pocket clip — also used to attach microphone to a lapel, blouse or lanyard. 4. Mute Button — press to mute, un-mute and pair microphone. 5. Acoustic Cover — protects delicate ...

- 15 - Adjusting the Volume on the Wearable Microphone Earpiece To change the volume on the Wearable microphone earpiece, use the dial on the earpiece wire. Turning the dial towards the earpiece, as shown in the figure, will increase the volume, and turning the dial towards the microphone will decre...

- 16 - 3. With the microphone in position on the table, un-mute the microphone by pressing and releasing the Mute button (confirm by a flashing GREEN LED). 4. To turn microphone off, return the microphone unit to the Charger Base or press and hold the Mute button for ~10 seconds until the LED turns ...

- 17 - 5 4 3 2 1 1. Remove the microphone from the Charger Base to turn on and automatically mute the mic. (indicated by a flashing RED LED) 2. Directional Tabletop microphones should be located on the table with the acoustic cover pointed toward the users, trying to keep the microphone 2 to 6 feet ...

- 18 - 2. Charging Port — docks to all Revolabs HD Charger Bases. 3. Mute button — press to mute, un-mute and pair microphone. 4. LED display — visual status for mute, un-mute, and pairing. 5. XLR Female connector — balanced audio for dynamic microphones. To use the HD Universal Wireless Adapter: 1....

- 19 - 5 4 3 2 1 1. Audio Out port — accepts the 2.5mm plug for the earpiece. 2. Charging Port — docks to all Revolabs HD Charger Bases. 3. Mute button — press to mute, un-mute and pair microphone. 4. LED display — visual status for mute, un-mute, and pairing. 5. TA4F connector — connects to Country...

- 20 - 1 2 3 Note: Microphones in new systems must be paired to the Base Station with each microphone assigned to a unique channel on the Base Station. Remember, microphones are always muted (flashing RED LED) when they are removed from the Charger Base and the Mute button needs to be pressed to mak...

- 21 - Power Module The Charger Base requires 5VDC power, provided by the AC Adapter. Plug the supplied AC adapter into an appropriate power outlet 110-240 AC, 50-60Hz. The power LED on the Charger Base will illuminate. Charging the Microphone Batteries First-time use — Before using the wireless mic...

- 23 - Warranty Revolabs, Inc. warrants this product to be free of manufacturing defects. Repair or replacement of any defective part or unit (at the discretion of the Seller) will be free of charge for the period defined in the Revolabs Professional Products Limited Warranty. Any attempt by the use...

- 24 - Specifications Dimensions, (L, W, H) and Weight : HD Venue Base Station 16.9‖ (43.03 cm) x 8.0‖ (20.32 cm) x 1.7‖ (4.42 cm), 2.0 lbs (5.45 kg) HD Charger Base 4.6‖ (11.75 cm) x 3.125‖ (7.9 cm) x 1.0‖ (2.54 cm), 0.325 lbs (0.147 kg) Wireless Microphones Wearable: 0.9‖ (2.3 cm) x 0.8‖ (2.0 cm) ...

- 25 - Index Adjusting the Volume, 15 Base Station, 7 Back Panel, 7 Front Panel, 7 Channel LED indicators, 8 Channels, 9 Charger Bays, 20 Charging the Batteries, 21 First-time use, 21 Recharging, 21 Connections , 8, 9 Earpiece, 9 Full-Duplex, 9 Indicator LEDs, 22 Input Connectors, 9 LED indicator, 2...