Raypak RAY014781 - Manuals

6 3. BEFORE INSTALLATION 3.1. Safety This appliance is to be installed and operated by trained personnel in accordance with this Installation and Operation Manual. Be sure to read and understand the entire Installation and Operation Manual before attempting to install or operate this appliance. Fail...

8 4.2. Clearances A A AVERTISS EMENT: Cet appareil doit être installé conformément au National Fuel gas Code ANSI Z223.1, et aux exigences de l’autorité competente. NOTE: The heater should not be located in an area where possible water leakage will result in damage to the area adjacent to the heater...

9 Figure 5. Florida Building Code Tie-Down Method Amp Draw 120 Volt 240 Volt 4 2 Figure 4. Heater Dimensions

10 This heater must b e installed at least 5' (1.52 m) from the inside wall of a pool unless separated from the pool by a solid fence, wall or other permanent solid barrier. Ce chauffe-piscine doit êntre installè à au moins 5 peds (1.52 m) de la paroi interne de la piscine à moins d’êntre isolé de l...

11 See Vent Piping section for details. Minimum allowable space is shown on the rating plate. Follow the installation instructions provided with the Indoor Drafthood Kit for installation. NOTE: For Canada, indoor installation is restricted to an enclosure that is not occupied and does not directly c...

12 24" MIN (610 mm) 5' (1.5 m) MIN 8' (2.4 m) OR LESS VENT CAP VENT PIPE DRAFTHOOD HEATER 24" MIN (610 mm) Figure 8. Vent Piping Requirements The weight of the vent stack or chimney must not rest on heater drafthood. Support must be provided in compliance with applicable codes. The heater to...

14 4.7.7. Internal Automatic Bypass Valve A built-in automatic bypass valve is provided in the In/Out header. The internal bypass valve automatically responds to changes in water pressure in the piping system. The proper amount of water flow is maintained through the heater under varying pressures d...

15 4.8. Electrical Connections Be sure that electrical service to the heater has proper overload fuse or circuit breaker protection, wire size and connections which comply with all applicable codes.If any of the original wire as supplied with the appliance must be replaced, it must be replaced with ...

16 5. CONTROLS 5.1. P-106 Control Adjustments The P-106 has an analog control system. The pool or spa water temperature is controlled by the thermostat on the upper front panel of the heater. The control center contains an On/Off toggle switch and a thermostat. The switch functions as a means for tu...

18 Figure 25. Run Time Indicator Press the DOWN button. The Fault History displays up to ten faults in memory. The order of the faults begins with “Fault Last,” which is the most recent fault, and proceeds through ten most recent messages in chronological order. The second line of the display shows ...

20 5.4.1. Remote Control Installation and Operation CAUTI ON: Before installing remote controls to the P-156 heaters, read the following: The digital thermostat model is remote-ready in most cases. The digital liquid crystal display (LCD) shows the actual pool temperature, operating status, and serv...

22 On P-106 heaters, splice into the red/white wire to connect the time clock. For P-156 heaters the fireman’s switch connection is located on the 14-pin header connected to the digital control board. Splice into the red wire jumper tagged “Where necessary add “Fireman’s” switch circuit here” to con...

24 7. MAINTENANCE The following preventative maintenance is to be performed one month after start-up and semi-annually thereafter. 1. Inspect top of heater and drafthood for soot, a sticky black substance around finned tubes and “V” baffles, and open flue gas passageways. Any visible soot should be ...

25 7.1.4. Flame Roll-Out Safety Switch Heaters are equipped with a thermal cutoff device to prevent flame roll-out in the event the heat exchanger becomes blocked. This is a “single-use” type fusible link or thermal fuse, that must be replaced when disabled by an over-temperature condition, caused b...

28 8.2. P-106 Control Logic Flow Chart START Turn knob to a desired temperature zone. Turn switch on. NO After six (6) seconds, does the pilot spark? YES Is the pilot lit? NO NO YES YES Do the burners light? END NO YES Is there power to the heater? Check the gas valve. There must be 24VAC between PV...

30 1-J 1-G 1-R 1-S 2-S 3-S 2-M 3-M 4-M 1-J 2-J 2-J 3-J 4-J 4-J 1-V 2-V 3-V 4-V 11-M 12-M 1-B 10-S 5-S 6-S 7-S 8-S 9-S 9-S 3-B 6-C 8-C 9-C 2-H 3-H 4-H 5-H 6-H 6-H 7-H 7-H 2-C 3-C 10-M 9-M 8-M 5-V 5-C 4-S 7-C 4-C 10-C 9. ILLUSTRATED PARTS LIST