RadioShack PLCD35 - Manuals

Page 2 - CUSTOMER NOTICE; F o r C D / R W + R D S + M P 3 m o d e l w i t h o p t i o n a l S U B W O O F E R f u n c t i o n

1 SW + REMOTE - 1PAU SEL 4 3 RPT SCN 2 6 SHF 5 TA AF CLK APS PTY PWR MODE FLIP DOWN DETACHABLE CD PLAYER OPEN BAND CUSTOMER NOTICE F o r C D / R W + R D S + M P 3 m o d e l w i t h o p t i o n a l S U B W O O F E R f u n c t i o n F o r C D / R W + M P 3 m o d e l w i t h o p t i o n a l S U B W O O...

Page 3 - BASIC OPERATION; For CD model with optional SUBWOOFER function

2 CDC CONNECTOR OR AUX CABLE BASIC OPERATION RESET 24 25 For CD model with optional SUBWOOFER function SW + REMOTE - 1PAU SEL 4 3 RPT SCN 2 6 SHF 5 DSP MUTE CLK A.PS SCAN PWR MODE FLIP DOWN DETACHABLE CD PLAYER OPEN BAND For CD model with optional SUBWOOFER function SW + REMOTE - 1PAU SEL 4 3 RPT SC...

Page 4 - ENTER

3 1. OPEN BUTTON Press it to flip down the front panel then you can insert the cd disc into the cdcompartment. 2.3.7 SEL (AUDIO MODE SELECT)/ +/- BUTTONS Press SEL button to change the mode in the sequence of A. The volume level can be adjusted at any time by pressing the audio level+or- button as s...

Page 5 - or; EONTA LOCAL / EONTA DISTANCE; EONTA DISTANCE; mode

4 BASIC OPERATION 14. CLOCK BUTTON Press it to display time on LCD for few seconds. Press it hold and then press or button to adjust hour or minute. 15. AF BUTTON (for RDS model only) AF [ALTERNATIVE FREQUENCIES]When pressed short, AF switching mode is selected and the state of AF switchingmode is d...

Page 7 - ELECTRIC CONNECTION

6 ELECTRIC CONNECTION NOTE:In spite of having any kinds of speaker system,must use 4 ohms impedance of speakerto reduce the distortion during high volume level. FOR 4X7W or4X30W FOR SUBWOOFER (4X7W or 4X30W) OR RED YELLOW BLACK BLUE VIOLET VIOLET/BLACK FRONT RCA OUTPUT CABLE (optional) RCH RED LCH W...

Page 8 - INSTALLATION

PLASTIC TRIM OUT KEY PLATE KEY PLATE 7 INSTALLATION HEX NUT SPRING WASHER PLAIN WASHER TAPPING SCREW DASH BOARD METAL MOUNTING STRAP CONSOLE SLIDE BRACKET HOUSING HEX BOLT While installing the front panel,please mount the left side first,then push the right side. TAPPING SCREW (M1.7X4 KM BLACK)

Page 9 - vehicle metal. Please confirm it before installation.

8 INSTALLATION ( FIG.1) ( FIG.2) ( FIG.3) ( FIG.4) CAUTION: Do not install the detachable panel before connecting the wire. 1. The unit is designed for negative terminal of the battery which is connected to the vehicle metal. Please confirm it before installation. 2. If the car interior is extremely...

Page 10 - Preparing the Remote Control; 0 degree in each the direction of the front of the IR mark.; DISC NOTES; L a b e l

9 DISC PLAY:Cleaning discsBefore playing, clean the disc with a clean, lint-free.Flip the disc in the direction of the arrow.NOTE:Do not use so solvents such as benzine, thinners. Commercially availablecleaners or anti static spray damage the unit.Insert a disc with the label surface down. Doing so ...

Page 11 - SPECIFICATIONS; GENERAL

10 SPECIFICATIONS GENERAL Power requirement .............................................................................................DC 12V Current consumption .....................................................................................5A or 15A POWER OUTPUT ...............................

Page 12 - TROUBLE SHOOTING; Symptom

TROUBLE SHOOTING Before going through the check list, check wiring connection. Should any of theproblems persist after check list has been made, consult your nearest service dealer. Symptom Cause Solution No power. The car ignition switch is If the power supply is properly not on. connected to the c...