RadioShack 43-3821 - Manuals

In s ta lla ti o n 10 6. Lift the base’s antenna to a vertical position. % 100'%6+0) ." % *#4)+0) " #0& " 4 '2.#%+0) " 6*' " $ #66'4; " 2 #%- The phone comes with a rechargeable Ni-Cd (nickel-cadmium) battery pack installed in the handset, but not connected. Before using ...

11 In s ta lla ti o n About once a month, fully discharge the battery pack by keeping the handset off the base until TALK/BATT flashes. Otherwise, the battery pack loses its ability to fully recharge. The supplied battery pack should last about a year. If the battery pack does not hold a charge for ...

In s ta lla ti o n 12 If your phone system requires that you dial an access code (9, for example) before you dial an outside number, do not dial the access code. The phone exits setting mode if a call or page is received, or if you press END . If the battery power is too low, the dialing mode might ...

14 T e lephone O pera tion If you do not have any special phone services, pressing FLASH might disconnect the current call. 7 5+0) " 4 '&+#. You can quickly dial the last number you dialed. Lift the handset and press TALK , then press RDL/ PAUSE when you hear a dial tone. ± 7 5+0) " 6 10...

16 Answ ering S ystem O perat io n To dial a number stored in memory location 1, press SPEED DIAL . You do not have to press TALK when you press SPEED DIAL . % *#+0 / & +#.+0) " 5 '48+%' " 0 7/$'45 To quickly recall numbers for special services (such as bank-by-phone), store each group o...

17 Answe ring S yst em O perat io n 5 '66+0) " 6*' " & #; 1 6 +/' You must set the day and time so the system can record the correct day and time of each message. ±ý 1. Press MENU once. The system announces “Time,” then the currently set time, day, and the day’s number ( '''' for Sunday,...

18 Answ ering S ystem O perat io n 2. Repeatedly press | 6 or 7 | until the desired number appears. 3. Press SET/RING to store the setting. The system beeps and announces “Ring Time” and the currently set ring time. 5 '66+0) " 6*' " 4 '%14& " 6 +/' You can set the recording time to '...

19 Answe ring S yst em O perat io n 3. Press SET/RING to store the setting. A beep sounds, then the system announces “Message Alert” followed by the new setting. When the first new message is received, a beep sounds. 6 740+0) " 6*' " / '55#)' " # .'46 " 6 10' " 1 (( " The Mes...

21 Answe ring S yst em O perat io n Press VOL 8 or 9 to adjust the call screening volume level. If you do not want to listen to calls, repeatedly press VOL 9 until &&&& appears. ± 4 '%14&+0) " + 0%1/+0) " / '55#)'5 After the system answers a call, it plays the outgoing me...

25 Answe ring S yst em O perat io n play incoming message, press #### 2 . For help, press #### 0 .” If the system does not respond, try entering your code again. If you enter an incorrect code three times, the system beeps and disconnects. 4. While the system is beeping, press # and (within 2 second...

T roubleshoot ing 26 6417$.'5*116+0) 2TQDNGO 5WIIGUVKQP Low volume or unusual sounds. Someone has picked up another phone on the same line. Hang up the other phone. Severe noise interference. Press CH to change the channel. Keep the handset away from computers, remote control toys, wireless micropho...

Care 27 If you still have problems, disconnect the phone. If other phones on the same line work properly, the fault is in this phone or its installation. If you cannot find the problem, take your phone to your local RadioShack store for assistance. %#4' Keep the phone dry; if it gets wet, wipe it dr...

43-3821 UCZZ01378BZ 04A02 Printed in China RadioShack CorporationFort Worth, Texas 76102 Limited One-Year Warranty This product is warranted by RadioShack against manufacturing defects in material and workman-ship under normal use for one (1) year from the date of purchase from RadioShack company-ow...