RadioShack 43-3813 - Manuals

7 Installation Phone Pick-Up Detection — stops recording when you pick up any phone on the same line as the answering system, and resets to answer the next call. Toll-Saver — lets you avoid unnecessary charges when you call by long distance to check your messages. ˆ Installation MOUNTING THE PHONE Y...

8 Installation On a Wall Plate or Wall 1. Insert the two tabs at the top of the narrow end of the supplied bracket into the base’s upper tab slots, then press down on the bracket’s latches and insert them into the lower slots. 2. Plug one end of the supplied short modular cord into the TEL LINE jack...

11 Telephone Operation ˆ Telephone Operation MAKING AND RECEIVING CALLS To make a call, lift the handset then press TALK . The TALK/BATT indicator on the handset and CHARGE/IN USE indicator on the base light. Dial the number. To answer a call, simply lift the handset from the base. If the handset is...

12 Telephone Operation PAGING To page the person who has the handset or to locate the handset when the phone is not in use, press PAGE on the base. The handset beeps for 1 minute. To stop it from beeping sooner, press any key on the handset or return the handset to the base. Press PAGE again to stop...

13 Telephone Operation Chain-Dialing Service Numbers For quick recall of numbers for special services (such as alternate long distance or bank by phone), store each group of numbers in its own memory location. To use the stored special service information, dial the service’s main number first. Then,...

14 Answering System Operation ˆ Answering System Operation USING THE MENU BUTTON Use MENU on the base to select function settings. Each time you press MENU , the system announces the function and its current setting. Note: The system exits the menu setting mode when you: • wait more than 20 seconds ...

16 Answering System Operation RECORDING/DELETING AN OUTGOING MESSAGE Follow these steps to record your own outgoing message (less then 30 seconds in length). 1. Press MENU once. The system announces “Greeting message”, followed by the current outgoing message. #ý# #ý# #ý# #ý# appears. 2. Press MEMO/...

17 Answering System Operation • The system detects a busy signal or more than 7 seconds of silence. • You pick up the system’s handset or any phone on the same phone line. Note: When the system's message memory is full, the caller will hear the prerecorded announcement-only message ("Hello, no o...

18 Answering System Operation announces the day and time of the call at the end of each message. To play all messages after playing the new messages, press PLAY/STOP again. To skip to the next message, press SKIP / ; ; ; ; while the message is playing. Hold down SKIP / ; ; ; ; to fast forward throug...

19 Answering System Operation 3. Repeatedly press or hold down SKIP / ; ; ; ; or : : : : / REPEAT to change the number. 4. Press SET to store the setting. The system announces the newly set code. 5. Press PLAY/STOP . To check your code at any time, press MENU three times. The code appears in the mes...

20 Troubleshooting Notes: • When the system is in remote operation, it stops all answering functions and the display on the base shows h9 h9 h9 h9 . The system resumes answering functions when it is no longer in remote command if you have not turned it off. • The remote operation stops when someone ...

21 Troubleshooting If you still have problems, disconnect the phone. If other phones on the same line work properly, the fault is in this phone or its installation. If you cannot find the problem, take your phone to your local RadioShack store for assistance. CARE Keep the phone dry; if it gets wet,...

22 Troubleshooting FCC STATEMENT Your telephone complies with Part 68 of the FCC Rules. Upon request, you must provide the phone’s FCC registration number and REN to your telephone company. These numbers are on the bottom of the base. Note: You must not connect your telephone to: • coin-operated sys...