RadioShack 15-1925 - Manuals

Need help? Call 1-800-950-7044 6 Notes: • The remote control’s red light turns on when you press a key, and blinks when you haveentered a feature or manufacturer’s code. • Whenever you use RECORD on the remote control, you must press it twice. This safetyfeature helps you avoid accidentally record-i...

Need help? Call 1-800-950-7044 7 PREPARATION INSTALLING BATTERIES You need four AAA batteries to power your re-mote control. We recommend alkaline batteries,such as RadioShack Cat. No. 23-555. 1.Press the battery compartment covertab and lift off thecover. 2.Install four AAA alka- line batteries as ...

Need help? Call 1-800-950-7044 8 SETTING UP THE 6 IN 1’S RF COMMAND CONSOLE After you install batteries in the 6 in 1, just plug theRF command console’s power cord into any stan-dard AC outlet in the same room as your IR re-mote-controlled devices (TV, VCR, cable box,and so on) and fully extended it...

Need help? Call 1-800-950-7044 12 OPERATION 1. Press the device key for the device you want to operate, then point the 6 in 1 at the deviceand press PWR (or CH s for some cable con- verters) to turn the device on. 2. Repeat Step 1 for all other devices you want to operate. 3. Point the 6 in 1 IR/RF ...

Need help? Call 1-800-950-7044 13 2. Aim the 6 in 1 IR/RF Remote Control at the device and press SCAN . The 6 in 1 scans through the channels. Note: The 6 in 1 must be pointed at thedevice the entire time you are using theChannel Scan feature. 3. To stop scanning, simply press any key (other than SC...

Need help? Call 1-800-950-7044 15 COMMAND SEQUENCES You can set up your 6 in 1 IR/RF Remote Controlto issue a set of up to 15 commands at the pressof a key. Any sequence of commands you regu-larly perform can be reduced to a single keypress. Setting a Sequence Here is an example of how to set up a s...

Need help? Call 1-800-950-7044 16 3. Press and release SET UP , then hold down SET UP until the red light blinks twice. This means that your sequence is erased. PUNCH-THROUGH Using Punch-Through The punch-through feature lets you alternatelycontrol two different devices without pressing thedevice se...

Need help? Call 1-800-950-7044 17 Follow these steps to turn off punch-through. 1. Press the device key ( CBL or VCR ) for the device you want to use to control the volume,for example. Then press SET UP until the red light blinks twice. 2. Press 9 – 9 – 3 . The red light blinks twice. Press the devi...

Need help? Call 1-800-950-7044 19 8. To brighten or dim lights connected to lamp and appliance modules, press the digit keyfor the module you want to control. Thenhold down Brt or Dim on the remote control (or BRIGHT or DIM on the IR command con-sole). Release the key when the desiredbrightness is r...

Need help? Call 1-800-950-7044 20 IF YOU HAVE PROBLEMS MANUAL CODE SEARCH If the 6 in 1 IR/RF Remote Control does not oper-ate your remote-controlled devices when you firstset it up, you might have to find the correct codefor your devices. You can try all the codes listedin the “Manufacturer’s Codes...

Need help? Call 1-800-950-7044 21 If necessary, repeat these steps for each device. Determining the 3-Digit Code After you set up your 6 in 1 IR/RF Remote Controlusing the manual code search, you can find which3-digit code the 6 in 1 IR/RF Remote Control isset to by following these steps. 1. Press t...

Need help? Call 1-800-950-7044 22 TROUBLESHOOTING If the 6 in 1 IR/RF Remote Control stops workingafter you have successfully tested the control foreach device, or if you are unable to get the remotecontrol to work at all, check these things: • Confirm that your remote control devices are working pr...

Need help? Call 1-800-950-7044 23 To upgrade your 6 in 1 IR/RF Remote Control,simply follow these steps: 1. Write down the brand names, model num- bers, RadioShack Cat. No. (if applicable)and manufacture dates for each type ofdevice (TV, VCR, cable box, etc.) that youwant to load into your 6 in 1 IR...

Need help? Call 1-800-950-7044 24 Notes: • You must hold the earpiece of your tele- phone over the receiver of your remotecontrol as shown above. If you do not, the6 in 1 IR/RF Remote Control might not beable to properly receive the informationcoming through the telephone. • While the 6 in 1 IR/RF R...

Need help? Call 1-800-950-7044 26 MANUFACTURERS’ CODES The following list tells you which 3-digit codes toenter to set up the 6 in 1 IR/RF Remote Control. Notes: • The 6 in 1 IR/RF Remote Control will not always be able to reproduce every commandof your original remote control. • A key on the 6 in 1...

Need help? Call 1-800-950-7044 50 FCC CAUTION This equipment generates and uses radio fre-quency energy, and if not installed and usedproperly, that is, in strict accordance with themanufacturer’s instructions, may cause interfer-ence to radio and television reception. It has beentype tested and fou...

Need help? Call 1-800-950-7044 51 CARE AND MAINTENANCE Your RadioShack 6 in 1 IR/RF Remote Controlsystem is an example of superior design andcraftsmanship. The following suggestions willhelp you care for your system so you can enjoy itfor years. • Keep the 6 in 1 and RF command console dry. If they ...

Need help? Call 1-800-950-7044 52 SPECIFICATIONS Remote Power..................................... 4 AAA Batteries RF Command Console Power................. 120 Volts AC Remote to RF Command Console Range .............................................100 Feet (304.8 m) RF Command Console to Device Ra...

Need help? Call 1-800-950-7044 53 NOTES 15-1925.fm Page 53 Monday, July 19, 1999 12:59 PM