Pyle PLTV165 - Manuals - manualsarea.com

Page 2 - Electrical Connection; CONTENTS

Important Safety Instruction ....................................................... Installation .................................................................................... DIN Front-Mount (Method A) ......................................................... Installing the unit ...............

Page 3 - IMPORTANT SAFETY INSTRUCTION

3 IMPORTANT SAFETY INSTRUCTION Please read the following safety instructions carefully. 1.This set has been designed and manufactured to assure personal safety. Improper use can result in electric shock or fire hazard. The safeguards incorporated in this unit protect you if you observe the following...

Page 4 - INSTALLATION; Take out screw; Installation Opening; pull it out to remove it.

5 3 m m 1 8 2 m m INSTALLATION Choose the mounting location where the unit will not interfere with the normal driving function of the driver.Before finally installing the unit, connect the wiring temporarily and make sure it is all connected up properly and the unit and the system Use only the parts...

Page 5 - Removing the unit

5 Outer Trim Ring L Key Sleeve R Key INSTALLATION Mount the sleeve by inserting thesleeve into the opening of the dashboard and bend open the tabs located around the sleeve with a screwdriver. Not all tabs will be able to make contact, so examine which ones will be most effective. Bending openthe ap...

Page 6 - Car radio mounting bracket

INSTALLATION DIN REAR-MOUNT (Method B) 1. Factory radio mounting bracket2. Car radio mounting bracket 3. Screw 4. After aligning the car radio mounting bracket with the factory radio mounting bracket, tighten the screws (5x5mm) at 2 places on each side. 5. When fix the factory radio mounting bracket...

Page 7 - ELECTRICAL CONNECTION

7 RGB SYSTEM A U D IO 2 L IN A U D IO 2 R IN V ID E O 2 IN W H IT E R E D Y E L L O W To Diversity Antenna A U D IO L O U T V ID E O O U T A U D IO R O U T G N D (B L A C K ) M E M O R Y B A C K -U P (Y E L L O W ) 3 A A C C (R E D ) R E M O T E C O N T R O L R E C E IV E R TV ANT AV INPUT DC IN REM...

Page 8 - OPERATION; LOCATION AND FUNCTION OF KEYS

7 9 1 1 2 8 1 0 2 11 6 5 1 5 3 1 4 1 6 4 1 3 8 OPERATION LOCATION AND FUNCTION OF KEYS

Page 9 - POWER

OPERATION LOCATION AND FUNCTION OF KEYS 9 1. /I POWER 2. OPEN/CLOSE3. IR4. AUDIO IN (AV1)5. VIDEO IN (AV1)6. 6.5 inch MULTI COLOR TFT MONITOR7. Reset8. VOLUME 9. VOLUME10. MENU11. TV/AV12. AUTO13. IR 14. CHANNEL15. CHANNEL16. 4:3/16:9 Selector 17. POWER 18. OPEN/CLOSE19. TV/AV20. 0~9 Numeric buttons...

Page 10 - SWITCHING ON/OFF THE UNIT; Switch on the unit by pressing; Press; IR; monitor will stretch automatically.; ANGLE; front panel or press; There is a remote sensor

F i g . 3 1 0 OPERATION SWITCHING ON/OFF THE UNIT Switch on the unit by pressing POWER button (1) on the front panel or POWER button (17) on the remote control. When system is on, press it again to turn the unit off. OPEN/CLOSE THE MONITOR AND ANGLE ADJUSTMENT Press OPEN/CLOSE button (2) on the fron...

Page 11 - RESET FUNCTION; Selecting receiving mode; Menu Function; MENU

11 OPERATION The external remote receiver is placed near the monitor for the best to receiver remote signal easily.If the angle of the monitor from vertical 0 exceeds 20 (Especially the distance exceeds 3m.), controlling the TV through IR (3) or (13) cannot get good effect. You are suggested to use ...

Page 12 - Auto Searching channels; SPECIFICATION; GENERAL

1 2 OPERATION Auto Searching channels Press AUTO button (12) on the monitor panel or AUTO button (23) on the remote control to enter into auto searching mode, then press CHANNEL button (14) on the monitor panel or CHANNEL button (26) on remote control t to start searching TV channels. Then press CHA...