Pyle PLPK5TVD - Manuals - manualsarea.com

Page 2 - INSTALLATION; driving function of the driver.; INSTALLATION HARDWARE

2 INSTALLATION Notes: • Choose the mounting location where the unit will not interfere with the normal driving function of the driver. • Before finally installing the unit, connect the wiring temporarily and make sure it is all connected up properly and the unit and the system work properly. • Use o...

Page 3 - Installing the unit

3 MOUNTING THE TUNER UNIT 1. Bracket (A) 5. Tapping Screw with Washer (M5 x 12) 2. Mounting Bolt (M5 x 5) 6. Spring Washer (M6) 3. Bracket (B) 7. Spring Washer (M5) 4. Hexagonal Bolt with Washer (M6 x 12) 8. Double Sided Tape INSTALL THE DISPLAY UNIT Before install the display unit, please remove it...

Page 5 - HOW TO OPEN AND CLOSE THE SCREEN DISPLAY; Press release button to draw out the screen display.; Release Button

HOW TO OPEN AND CLOSE THE SCREEN DISPLAY 1. Press release button to draw out the screen display. 2. Turning the display upward. 3. Adjusting the viewing angle. Angle should be adjusted slowly without applying unreasonable force. Release Button 5

Page 6 - before drawing in. It cannot be draw in with its angles adjusted.

6 4. Turning the display downward. Make sure to return the display to centre position before drawing in. It cannot be draw in with its angles adjusted. 5. Push the panel, the display will be drawn in.

Page 7 - ELECTRICAL CONNECTION

7 ELECTRICAL CONNECTION RADIO/TV MAIN UNIT (VIEW FROM REAR) TV DIVERSITY ANTENNA INPUT GREY TV CONTROL GREY/BLACK TV DIVERSITY ANTENNA INPUT RADIO ANTENNA INPUT BLUE/WHITE POW ANT REAR Rch SPK VIOLET VIOLET/BLACK FRONT Rch SPK GREY GREY/BLACK REAR Lch SPK GREEN GREEN/BLACK FRONT Lch SPK WHITE WHITE/...

Page 8 - OPERATION

OPERATION 18 21 22 17 1 23 4 20 9 10 19 8 15 4 12 3 14 6 8 5 1 11 7 16 2 13 24

Page 9 - GENERAL OPERATION; VOL

GENERAL OPERATION • ON/OFF Switch on the unit by pressing PWR button (1). When system is on, press it again to turn it off. • FACEPLATE RELEASE Press REL button (2) to draw out the faceplate, push the panel to draw in. When the faceplate is drawn out, turn the faceplate upward and adjust TV display....

Page 11 - RADIO OPERATION; Press

11 RADIO OPERATION • SELECTING BAND Press BAND button (11) to change between three FM bands and two AM bands. Each band stores up to six preset stations. • SELECTING STATION During radio mode, press MAN/SKP button (13) to increase frequency or (14) to decrease frequency by one step of channel spacin...

Page 13 - TUNER MENU; You can use

13 Note: When you set the color mode to “PAL” in SYSTEM MENU, there is no “TINT”item to display.In this menu, the range of setting value is 00~63, and the recommended range ofthese values are listed below: BRIGHT: 10~32 CONTRAST: 20~40 COLOR: 40~50 SHARP: 63 TINT: 10 TUNER MENU --POSITION -- POSITIO...

Page 15 - SYSTEM MENU

15 --SEARCH-- SEARCH setup Use CONTROL+ button (19) or CONTROL– button (20) to start manual station search. And it will start from the band you select in BAND setup. The SKIP and AFTtwo items will be set automatically. --ASM-- ASM (Auto Search Memory) setup Use CONTROL+ button (19) or CONTROL– butto...

Page 17 - In AV mode

17 --CORING-- CORING setup Use CONTROL+ button (19) or CONTROL– button (20) to switch between ON and OFF. When the coring function is on, it can effectively decease the picture noiseand improve the image quality. --HALFTONE-- HALFTONE setup Use CONTROL+ button (19) or CONTROL– button (20) to switch ...

Page 18 - • PROGRAM SCANNING; SCAN; button (22), “SCAN OFF” will display on the lower left corner of the; • SCREEN DISPLAY; DSP

18 • PROGRAM SCANNING Press SCAN button (22), “SCAN OFF” will display on the lower left corner of the screen. Press it again, the screen will display “SCAN ON”, then it begins to scan1.5 seconds of each channel in sequence. When it completes, the screen will display“SCAN OFF”.In the course of scanni...

Page 19 - REMOTE CONTROL HANDSET; CONTROL & FUNCTION KEYS

19 REMOTE CONTROL HANDSET 2 11 8 9 10 16 5 6 7 14 13 15 12 17 4 3 1 CONTROL & FUNCTION KEYS 1. POWER = Press POWER to turn the unit ON or OFF 2. TV/AV = Switch between TV/AV1/AV2 3. 0 - 9 = Numeric buttons, press to select the corresponding channel 4. -/-- = Digital selecting button, cooperative...

Page 20 - SPECIFICATION; GENERAL; FM

SPECIFICATION GENERAL P ower Supply Voltage : DC 12 Volts, Negative Ground Maximum P ower : 4 x 60 Watts Load Impedance : 10 Ampere (max.) Tone Controls- Bass (at 100 Hz) : + / – 10 dB - Treble (at 10 KHz) : + / – 10 dB TV Monitor Screen Size : 5.0” TFT Resolution : 960 x 234 dots TV Sensitivity : 4...