Pyle PLCDCS300 - Manuals - manualsarea.com

Page 2 - CONTENTS

2 Installation .....................................................................................................3 Wiring Connection ........................................................................................4 Operation ...................................................................

Page 3 - INSTALLATION

3 INSTALLATION Installation onto the car bracket using supplied screws (M5 x 6mm). The holes of thecar bracket to use will differ depending on the car model. Screw (M5 x 6mm)

Page 4 - WIRING CONNECTION

4 For 4 x 50W GREEN GREEN/BLACK GREY GREY/BLACK VIOLET VIOLET/BLACK MAIN UNIT WHITE WHITE/BLACK FRONT Lch SPEAKER REAR Lch SPEAKER FRONT RchSPEAKER REAR RchSPEAKER Rch RED Lch WHITE (GREY) RCA CABLE ANTENNA SOCKET RED BLUE POWER ANTENNA GROUND (B–) MEMORY BACK-UP IGNITION SWITCH (B+) WIRING CONNECTI...

Page 5 - OPERATION

5 OPERATION 28 27 29 5 9 12 26 25 3 2 15 7 17 16 13 8 6 10 11 4 1 18 19 20 21 30 22 23 24 14

Page 6 - GENERAL OPERATION

6 GENERAL OPERATION Note: In this product design, there has different sound accompanying with everybutton pressed and the sound isdesigned differently according to thecustomers. • ON/OFF Switch on the unit by pressing POWER button (9). When system is on, press POWER button (9) again to turn off the ...

Page 7 - RADIO OPERATION

7 Stations are searched automaticallyfrom next frequency and detected station is stored into the preset memory. In case of LOC state, the first Auto Store is done by LOC stateand if 6 CH is not fully memorized, the seconds Auto Store search continued by Distant state. At the end of Auto Store operat...

Page 8 - CASSETTE OPERATION; POWER; • EJECT

8 OPERATION CASSETTE OPERATION • TAPE OPEN/CLOSE Press TAPE OPEN/CLOSE button (26), the front panel will slide down to show the cassette compartment (28).Press TAPE OPEN/CLOSE button (26) again or POWER button (9) to slide up the front panel. • PROGRAM BUTTON These two buttons (27) perform the dual ...

Page 9 - CDP OPERATION

9 • REPEAT THE SAME TRACK Press RPT button (21) to continuously repeat the same track. Press it again to stop repeat. • PREVIEW ALL TRACKS Press SCN button (20) to play first several seconds of each track on the current disc.Press it again to stop intro and listen to track. • PLAY ALL TRACKS Press R...

Page 10 - FUNCTION KEYS & CONTROL; REMOTE CONTROL HANDSET

10 FUNCTION KEYS & CONTROL 1. PWR = Power Button 2. MUT = Mute Button 3. SEL = Select Button 4. VOL = Volume Up Button 5. VOL = Volume Down Button 6. BND = Band Select Button 7. MOD = Mode Button 8. TUNE/SEEK = Tune/Seek Down Button 9. TUNE/SEEK = Tune/Seek Up Button 10. EQ = Preset Equalization...

Page 11 - FM; SPECIFICATIONS

11 GENERAL P ower Supply Requirements : DC 12 Volts, Negative Ground Chassis Dimensions : 200 mm (W) x 138 mm (D) x 100 mm (H) Loading Impedance : 4 - 8 Ω per channel Maximum Output P ower : 4 x 50 Watts Current Drain : 10 Ampere (max.) CD PLA YER Signal to Noise Ratio : More than 55 dB Channel Sepa...

Page 12 - TROUBLE SHOOTING

12 Before going through the check list, check wiring connection. If any of the problemspersist after check list has been made, consult your nearest service dealer. Symptom Cause Solution No power. The car ignition switch is If the power supply is properly not on. connected to the car accessorycircui...

Page 13 - MAINTENANCE; For System

MAINTENANCE For System The following suggestions help you carefor the product so that you can enjoy itfor years. 1. Keep the product dry. If it does get wet, wipe it dry immediately.Liquids might contain minerals that can corrode the electronic circuits. 2. Keep the product away from dust and dirt, ...

Page 14 - CAUTION; IGNITION AND INTERFERENCE NOISE; Interference

CAUTION 1. This unit is designed to operate on 12-volts DC, negative ground electrical system only. Do not attemptto install this unit in a vehicle having apositive ground system. 2. You should not touch the high-polished playback head with anymetallic or magnetic tools. 3. Your unit has built-in fi...