Pyle PLCD22MRP - Manuals - manualsarea.com

Page 2 - CONTENTS

Installation .....................................3 Take out screw before installation ..3 Installing the unit ..........................3 Wiring Connection ........................4Operation .......................................5 Location of keys .............................5Control & functi...

Page 3 - TAKE OUT SCREW BEFORE INSTALL; INSTALL THE UNIT; According to the mounting paper; INSTALLATION; Take out screw before install.

3 TAKE OUT SCREW BEFORE INSTALL Before install the unit, please remove thetwo screws. NOTE: This unit is installed on the ship,so you should use two pieces of plasticfilm (30mmX20mm) supplied with the unitto seal the two holes after remove thescrews. And this will be waterproof. INSTALL THE UNIT 1. ...

Page 4 - WIRING CONNECTION

4 WIRING CONNECTION RED WHITE RED Rch WHITE Lch RCA CABLE (GREY) BLUE RED YELLOW BLACK POWER ANTENNA IGNITION SWITCH (ACC+) MEMORY BACK-UP (B+) GROUND (B-) FRONT Lch SPEAKER REAR LchSPEAKER WHITE WHITE/BLACK GREEN GREEN/BLACK FRONT Rch SPEAKER REAR Rch SPEAKER GREY GREY/BLACK VIOLET VIOLET/BLACK FUS...

Page 5 - OPERATION; When pull open the disc cover:

5 OPERATION When pull open the disc cover: 12 7 10 18 23 21 22 11 9 1 13 3 25 19 24 14 20 6 15 16 8 2 4 17 5 26

Page 6 - CONTROL & FUNCTIONS KEYS; Power button; Press; VOL

6 OPERATION CONTROL & FUNCTIONS KEYS This unit is a marine rated wired remote control made using a modified controller orsimilar layout. It is capable of operation specified functions on the marine AM/FM/CDreceiver and the marine AM/FM/Cassette receiver. The body, buttons, controls anddisplay ne...

Page 8 - INSTALLATION HARDWARE

8 OPERATION 1. First insert the hooks on the base into the slots of the holder to install the base to the holder. 2. Select the proper object, then place the remote mounting bracket on the base and let the object go through the base and the mounting bracket. INSTALLATION HARDWARE HOLDER BASE REMOTE ...

Page 9 - holder with the four slots on the remote control.

9 OPERATION 3. Align the screw holes on the holder with the screw holes on the base and the screw holes on the bracket, then use the two screws (ø4X50) and nuts to fix the bracket,the base and holder to the proper location. 4. Last install the remote control to the holder. See below, align the four ...

Page 10 - Hook

• SWITCHING ON/OFF THE UNIT Switch on the unit by pressing anybutton (except EJECT (4)). When system is on, press POWER button (9) to turn off the unit. When system powerturns on, the system is returned toprevious mode. • DISPLAY THE DISC SLOT Press the hook (7) of the plastic disccover then poke it...

Page 12 - RADIO OPERATION

of the LCD display backlight. RESET FUNCTION When you pull out the plastic panel coveringthe CD opening, you will see the resetbutton (26) is placed above the disc slot(5). It must be activated with either aballpoint pen or thin metal object. Thereset button is to be activated for thefollowing reaso...

Page 13 - CD OPERATION

CD OPERATION • SWITCHING TO CD MODE If there is no CD inserted in the driver:Gently insert the CD with the printedside uppermost into the CDcompartment until you feel someresistance. The CD will be drawn intothe driver automatically. CD playbackbegins.If a CD is already inserted in the driver:Keep p...

Page 14 - MP3 OPERATION

for several seconds will exit PGMmode. - When the disc is playing in programmed order, pressing MEM button (20) for several seconds willcancel the all programmed contentand “CLR” appears on the display. - If you don’t press MEM button (20) to carry out program setting, thenpress PGM button (21) for ...

Page 17 - FM; SPECIFICATION

17 GENERAL P ower Supply Requirements : DC 12 Volts, Negative Ground Chassis Dimensions : 178 (W) x 178 (D) x 50 (H) mm Tone Controls- Bass (at 100 Hz) : ± 10 dB - Treble (at 10 KHz) : ± 10 dB Maximum Output P ower : 4 x 50 Watts Current Drain : 15 Ampere (max.) CD PLA YER Signal to Noise Ratio : Mo...

Page 18 - TROUBLE SHOOTING; Symptom

18 TROUBLE SHOOTING Before going through the check list, check wiring connection. If any of the problemspersist after check list has been made, consult your nearest service dealer. Symptom Cause Solution No power. The ignition switch is not If the power supply is on. connected to the accessory circu...