Pyle PLCD20CH - Manuals

Pyle PLCD20CH – Manual in PDF format online.

Manuals:

Manual

Manual Pyle PLCD20CH

Summary

Page 3 - HOW TO USE THE MAGAZINE; Loading a disc

3 HOW TO USE THE MAGAZINE Loading a disc 1. Pick the tab on the magazine’s disc tray and pull out only of the trays. 2. Place the disc on the tray with its play surface facing down (label surface facing up).• Each tray can accommodate only one disc. 3. Press the tab on the disc tray to store the tra...

Page 4 - PRECAUTIONS FOR HANDLING DISCS; With new discs; • Operation changes to the next; WARNING; Burrs

4 PRECAUTIONS FOR HANDLING DISCS With new discs The symptoms described belowsometimes occur when new discsare used:• The disc is not played even when it is loaded. • Operation changes to the next disc before the first disc has achance to be played. • The same disc is played over and over again. • Th...

Page 5 - • Some functions do not operate.

5 INSTALLATION PARTS WIRING Connect this cable to the terminal of the CD player. RESET FUNCTION The reset button must be activated with either a ball point pen or thin metal object.It is to be activated for the following reason:• Initial installation of the unit when all wiring is completed. • Some ...

Page 6 - BEFORE INSTALLING THE UNIT; Transport Lock Screws; Do not install the unit in the following locations.

6 BEFORE INSTALLING THE UNIT Transport Lock Screws The mechanism in the CD changer is“locked” into place during shipment bythe transport screws.Be sure to remove the screws prior toinstallation. CautionAfter removing the transport lock screws, place the supplied seals over the screwholes.These seals...

Page 7 - Position of the built-in anti-vibration board; For use when unit is installed horizontally or suspended:; Confirm that the built-in anti-vibration board is set to position “0”.; For use when unit is installed vertically:; The built-in anti-vibration board should be set to position “90”.; For use when unit is installed at a 45; The built-in anti-vibration board should be set to position “45

7 Position of the built-in anti-vibration board This unit can be installed horizontally (suspended), vertically, and at a 45 ° angle. Once the installation position has been decided, it’s necessary to set the position ofthe built-in anti-vibration board inside the unit. Please do this before perform...

Page 8 - INSTALLATION; Procedure for Installation on Carpet (Horizontal Position)

8 INSTALLATION Procedure for Installation on Carpet (Horizontal Position) 1 2 3 4 5 • Confirm that the built-in anti-vibration boards on both the leftand right sides are set to the horizontal installation position “0”. • Attach the left and right brackets (A) using the hexagonal bolt (M4 x 5). • Att...

Page 9 - Procedure for Installation on Carpet (Vertical Position)

9 INSTALLATION Procedure for Installation on Carpet (Vertical Position) 1 2 3 4 5 • Set that the built-in anti-vibration boards on both the left and right sides are set to the vertical installation position “90”. • Attach the left and right brackets (A) using the hexagonal bolt (M4 x 5). • Attach th...

Page 10 - Procedure for Installation on Carpet (at a 45

10 INSTALLATION Procedure for Installation on Carpet (at a 45 ° angle) 1 2 3 4 5 • Set the built-in anti-vibration boards on both the left and right sides to the 45 ° installation position “45 ° ”. • Attach the left and right brackets (A) using the hexagonal bolt (M4 x 5). • Attach the left and righ...

Page 11 - Procedure for Installation (Suspended Position)

11 INSTALLATION Procedure for Installation (Suspended Position) 1 2 3 • Confirm that the built-in anti-vibration boards on both the leftand right sides are set to the horizontal installation position “0”. • Attach the left and right brackets (A) using the hexagonal bolt (M4 x 5). • Determine the mou...

Page 12 - Symptom Cause

12 HANDLING THE DISCS Dirt, dust, scratches and warpage cause sound skips during playback and adeterioration of sound quality. How to take care of your disc: 1. Use compact discs that have the mark shown on the right.2. Fingerprints and dust should be carefully wiped off the disc’s signal surface (g...

Page 13 - CD Changer Remote Control System

13 OPERATINGINSTRUCTIONS CD Changer Remote Control System SCAN SELECT REPEAT RANDOM OFF TRK/SKIP RESET DISC

Page 14 - PARTS AND THEIR FUNCTIONS; Control section

14 PARTS AND THEIR FUNCTIONS Control section Liquid Crystal Display (LCD) - (1) LCD display will only be active when the changer power is on. This display indicatesall operation key’s, including DISC number, track number. Select Button (2) Press this button to select functions.Functions are shown be...

Page 15 - Press this button to turn On/Off the changer.

15 Random Play Button (Track or DISC Random) - (5) This is used for random selection Disc play, and sequence.Once this button is pressed. “RANDOM ONE” is displayed in the Upper left cornerof LCD commander, and disc selection will begin random play.Press this button for a second, “RANDOM ALL” will be...

Page 16 - Reset Button; Initial installation after all wiring is completed.

16 Reset Button A reset button is located on the front panel of the unit which must be activated witha pen tip or other thin object as it is recessed to prevent accidental engagement. 1. Initial installation after all wiring is completed. 2. If abnormal disc operation is encountered, the reset butto...

Page 17 - BEFORE USING THE SYSTEM; SETTING UP FOR OPERATION

17 BEFORE USING THE SYSTEM SETTING UP FOR OPERATION Be sure to press reset button when all wiring is completed. Load the discs into theCD magazine and install the magazine into the CD changer. Wiring — Using FM Modulator This system is designed to convert CD sound into FM signals (89.1 MHz or 88.7MH...

Page 18 - CD CHANGER OPERATION; Listening to the CD Play

18 CD CHANGER OPERATION Listening to the CD Play • Playing a CD Press the play/pause button ( ....... ). Adjust the volume and tone using the FM car stereo to which the system is connected.* When using the system for the first time or when the CD magazine has just been replaced, play starts from the...

Page 19 - • Random play; Listening to the radio or tape; Press the power off button (; Procedure To Mount The CD Changer Commander unit; Installation of the FM Modulator/Ground Isolator

19 Commander FM Modulator/Ground Isolator M3 x 12 • Random play - When the random button (RANDOM) is pressed, “RANDOM ONE” appears, and the tracks on the disc now heard are played in a random order. When all the tracks have been played, they will be played again, this time in a different randomorder...

Page 20 - Wiring — FM Modulator unit

20 Wiring — FM Modulator unit ACC/Ignition power lead (red) Connect to where the power issupplied when the ACC power orignition switch is turned ON. Battery power lead (pink) Memory back up. To be connectedto continuous power source. Ground lead (black) Screw this to a metal part of thevehicle. Inte...

Page 21 - Control and Function Keys; the antenna to the FM Modulator’s large black antenna connector.

21 Control and Function Keys 1. +12V TO IGNITION Connect the red power wire (with in-line fuse holder) to a point in your vehicle’s fuseblock that has power only when you turn the vehicle’s key to either the accessory(ACC) or START position. 2. ANTENNA If your system does not have an RCA input jack,...

Page 22 - CD CHANGER COMMANDER

22 4. OUTPUT FREQUENCY Turn the switch on the side of the FM Modulator to choose the output frequency between 89.1 MHz and 88.7 MHz with a screwdriver. When the reception is interferedwith other station on the one frequency, switch to the another frequency. 5. RESET (FOR MODULATOR FUNCTION ONLY) If ...

Page 23 - TROUBLESHOOTING; Cause Remedy; Error Messages showing on display of controller:

www.pyleaudio.com Symptom Cause Remedy No power. Improper connection. Check connections. Magazine cannot Direction in which it is Insert it in proper direction. be installed. inserted is wrong. CD is not played. Disc has been loaded Load disc with play side facing upside down. up. Noise is heard Lar...