Page 2 - IMPORTANT NOTICE; CAUTION; Disc; ENVIRONMENTAL CONDITIONS
IMPORTANT NOTICE This Compact Disc Changer/Player has been tested and found to comply with thelimits for a class B digital device in accordance with the specifications in Subpart Jof part 15 of FCC Rules. This equipment generates and uses radio frequency energy,and it must be installed and used prop...
Page 3 - INTRODUCTION; RESET FUNCTION
2 INTRODUCTION RESET FUNCTION A RESET button is located on the front panel (to the left side of EJECT button) and isaccessible only when the magazine door is opened. The RESET button is recessedin order to prevent accidental engagement, and can be activated with the tip of ball-point pen or any simi...
Page 4 - LOCATION OF CONTROLS; Compact Disc Magazine Slot; WIRING CONNECTIONS; CAR RADIO
3 LOCATION OF CONTROLS 1. Compact Disc Magazine Slot 2. Reset Button 3. Eject Button (Press this button to eject the Magazine) 4. Slide Door WIRING CONNECTIONS CAR RADIO CD CHANGER 1 2 3 4
Page 5 - HOW TO USE THE COMPACT DISC MAGAZINE; Inserting Discs; Store the pulled-out magazine in a safe place.; Inserting the magazine; cause damage to the player if allowed to enter.; Removing the magazine
4 HOW TO USE THE COMPACT DISC MAGAZINE Inserting Discs Inserting Discs into the supplied magazine. Up to 6 Discs may be inserted into themagazine.The Disc are numbered from 1 (bottom tray) to 6 (top tray).Note: Do not touch the recorded side of a Disc while inserting or removing it. Removing Discs 1...
Page 6 - INSTALLATION; Location
5 INSTALLATION • Use the supplied parts and mount the unit securely. The use of parts other than these supplied (specified) may loosen or damage internal components. • If installation presents any difficulties, consult your dealer for advice.• Before drilling a hole into the wall or floor the vehicl...
Page 7 - ACCESSORIES; Important; key to appropriate angle: Of for horizontal. 45
ACCESSORIES x2 x2 x4 a) Bracket b) Floor base plate c) Hex bolt (M5x12) with Washers x4 x4 x4 x1 d) Wing nut (06) e) Self tape screw (5x15) f) Self tape screw (3x15) g) Mount angle adjust key Important Angle set and locking screws• Be sure to adjust the mounting angle set screw (F) using the mountin...
Page 8 - INSTALLATION DIAGRAMS; HORIZONTAL / VERTICAL INSTALLATION PROCEDURES
7 ø3.5mm c) e) e) a) a) c) Press the unit to the floor, andremove the wing nuts (d), and liftoff the changer Lay down the carpet. Cut 1 “X” oneach area of the carpet where themounting bolts will pass through Mount the unit in place, using 4wing nuts (d) Attach the brackets (a) to each side of the un...
Page 9 - VERTICAL INSTALLATION; FOR AN ANGLED INSTALLATION, TURN TO THE 45
VERTICAL INSTALLATION FOR AN ANGLED INSTALLATION, TURN TO THE 45 ° POSITION AND ATTACH LOCK SCREW (F1) IN THE MIDDLE HOLE. 8 Press the unit to the floor, andremove the wing nuts (d), and liftoff the changer Lay down the carpet. Cut 1 “X” oneach area of the carpet where themounting bolts will pass th...
Page 10 - SPECIFICATIONS; General
9 SPECIFICATIONS General System Compact Disc audio system Usable Discs Compact Disc Operation voltage 10 - 15V Power consumption 6W or less (DC 14.4V) Operating electric current 400mA 14.4Volt Max. peak electric current 1.2A 14.4Volt Dimensions 284(W) x 186.5(O) x 74(H) mm Operational temperature ra...
Page 11 - OPERATION; Press this button to turn On/Off the changer.
10 OPERATION Liquid Crystal Display (LCD) - (1) LCD display will only be active when the changer power is on. This display indicatesall operation key's, including DISC number. Track number, and DISC icon. Random Play Button - (2)(Track or DISC Random) This is used for random selection Disc play, and...
Page 12 - ERROR DISPLAY; passed in movement of Sled center area.
ERROR DISPLAY • Error 1: There's no Magazine, and DISC is clamping.• Error 2: It is impossible to discharge Magazine while ejecting.• Error 3: Loading is not completed after a certain time (8 sec) passed.• Error 4: Unloading is not completed after a certain time (8 sec) passed.• Error 5: Elevator do...