Porter-Cable 877 - Manuals - manualsarea.com

Page 2 - GENERAL SAFETY RULES; FOR ALL BATTERY OPERATED TOOLS; WORK AREA

2 GENERAL SAFETY RULES FOR ALL BATTERY OPERATED TOOLS WARNING! READ AND UNDERSTAND ALL INSTRUCTIONS. Failure to follow all instructions listed below, may result in electric shock, fireand/or serious personal injury. WARNING: SOME DUST CREATED BY POWER SANDING, SAWING, GRINDING, DRILLING, AND OTHER C...

Page 6 - ADDITIONAL SAFETY RULES FOR HAMMER-DRILLS; FUNCTIONAL DESCRIPTION; FOREWORD

6 ADDITIONAL SAFETY RULES FOR HAMMER-DRILLS 1. Apply forward force only on pistol grip handle and ONLY with your hands when drilling. 2. Do not use bits larger than those recommended. They may cause personal injury due to jamming and loss of control. Large bits may alsooverload the drill and damage ...

Page 7 - ADJUSTING TORQUE COLLAR

7 INSTALLING AND REMOVING DRILLAND SCREWDRIVER BITS 1. CAUTION: Always set reversing button to center (locked OFF) position wheninstalling and removing bits. 2. The three-jaw chuck is designed for self-centering of the bit. Open jaws largeenough by turning outer sleeve (A) Fig. 2,counterclockwise, w...

Page 8 - DRIVER BIT STORAGE; OPERATION; CHARGING THE BATTERY PACK GENERAL; Battery temperature will increase during and shortly after use.; NORMAL CHARGING; Disconnect charger from power source when not in use.

8 DRIVER BIT STORAGE Convenient storage areas with retaining clip(B) Fig. 4, for screwdriver bits are providedon each side of the tool. OPERATION CHARGING THE BATTERY PACK GENERAL Before using your cordless tool for the first time, the battery pack should befully charged. If the battery pack is inst...

Page 9 - A B

9 DIAGNOSTICS The Models 8604 and 8624 chargers are equipped with a diagnostic systemthat automatically checks the battery pack each time a pack is inserted intothe charger. If no problems are found, the charger will automatically switch to“Fast Charge” mode as described in NORMAL CHARGING. If a pro...

Page 10 - IT’S

10 HOW TO HOLD THE HAMMER DRILL/DRIVER WARNING: The front end of the Hammer Drill/Driver may be made live if the tool drills into live wiring in the wall. TO PREVENTELECTRICAL SHOCK, THE HAMMER DRILL/DRIVER MUST BEHELD AS SHOWN IN FIG. 7. GENERAL DRILLING 1. Set torque adjusting collar for drilling ...

Page 11 - enlarge it to the required size.; DRIVING WOOD SCREWS; Drill pilot and shank clearance holes. See following chart.; SUGGESTED HOLE SIZES; IT’S A

11 DRILLING WOOD In addition to the instructions listed under GENERAL DRlLLlNG, the followingalso apply: 1. When using twist drills in wood, they should be withdrawn from the hole frequently to clear chips built up in flutes to avoid overheating and burningwork. 2. If a backing block is used to keep...

Page 12 - Drilling Concrete

12 2. Install proper bit that fits screw to screwdriver. 3. Set torque adjusting collar for desired torque and set speed selector to LOW. 4. Set screwdriver for correct rotation. 5. Start screw straight in hole with fingers. 6. Place bit on screw, start screwdriver and exert pressure to drive screw....

Page 13 - Extreme care should be taken in the event bit should; MAINTENANCE; KEEP TOOL CLEAN; Remove battery pack to prevent accidental start-up.; REMOVE

13 CAUTION: Extreme care should be taken in the event bit should become jammed in the hole so that drill can be stopped immediately.See ADDITIONAL SAFETY RULES FOR HAMMER DRILL/DRIVERS,Number 7. MAINTENANCE KEEP TOOL CLEAN All plastic parts should be cleaned with a soft damp cloth. NEVER usesolvents...

Page 14 - SERVICE AND REPAIRS; ACCESSORIES; SPARE BATTERY PACKS

14 5. Place the short end of a large allen wrench ( 1 / 4 " or larger) into the chuck. Align wrench flats with chuck jaws and tighten chuck securely. Whilesupporting chuck on a solid surface, position allen wrench to left (see Fig. 9)and strike wrench a sharp blow with a hammer to loosen chuck. ...

Page 15 - NOTES

15 NOTES 900470 - 11-30-00.QXD 9/25/02 11:10 AM Page 15

Page 16 - ONE YEAR WARRANTY

16 PORTER-CABLE LIMITED ONE YEAR WARRANTY Porter-Cable warrants its Professional Power Tools for a period of one year from the date of originalpurchase. We will repair or replace at our option, any part or parts of the product and accessoriescovered under this warranty which, after examination, prov...

Page 17 - DELTA SERVICE CENTERS; CANADIAN PORTER-CABLE

The following are trademarks of PORTER-CABLE · DELTA Corporation (Las siguientes son marcas registradas de PORTER-CABLE · DELTA S.A.) (Les marques suivantes sont des marques de fabriquant de la PORTER-CABLE · DELTA Corporation): BAMMER ® , LASERLOC ® , OMNIJIG ® , POCKET CUTTER ® , PORTA-BAND ® , PO...