Porter-Cable 352VS - Manuals

Page 2 - SAFETY GUIDELINES - DEFINITIONS; WORK AREA; Keep your work area clean and well lit.; ELECTRICAL SAFETY; Read and understand all instructions.; Failure to; SAVE THESE INSTRUCTIONS.; GENERAL SAFETY RULES

2 Some dust created by power sanding, sawing, grinding, drilling, and other construction activities contains chemicals known (to the State of California) to cause cancer, birth defects or other reproductive harm. Some example of these chemicals are: ● ● lead from lead-based paints ● ● crystalline si...

Page 5 - Hz; LEAD-BASED PAINT SHOULD ONLY BE REMOVED BY A PROFESSIONAL.; Persons removing paint should follow these guidelines:; KEEP THE WORK AREA WELL VENTILATED.; Open the windows and; REMOVE OR COVER; in the work area to catch any paint chips or; ADDITIONAL SAFETY RULES FOR PAINT REMOVAL

5 SYMBOL DEFINITION V ........................ volts A ........................ amperes Hz ........................ hertz W ........................ watts kW ........................ kilowatts µ F ........................ microfarads l ........................ liters kg ........................ kilo...

Page 7 - DISCONNECT TOOL FROM POWER SOURCE.; FUNCTIONAL DESCRIPTION

7 If an extension cord is to be used outdoors it must be marked with the suffixW-A or W following the cord type designation. For example – SJTW-A toindicate it is acceptable for outdoor use. RECOMMENDED EXTENSION CORD SIZES FOR USE WITH PORTABLE ELECTRIC TOOLS FOREWORD The Porter-Cable Variable Spee...

Page 8 - Some sanding belts are bi-directional. These belts will not have; TO START AND STOP THE BELT SANDER; To release the lock button, squeeze the trigger and release.; VARIABLE SPEED; To prevent excessive wear on both the sander and belt,; NEVER; allow the; OFF”; necting the tool to the power source.

NOTE: Some sanding belts are bi-directional. These belts will not have arrows printed on them. They can be installed to run in either direction. 5. Engage the front pulley by pushing the lever (A) Fig. 1 back to its originalposition. TO START AND STOP THE BELT SANDER 1. Be certain that the the switc...

Page 9 - Hold the sander off the work before starting the motor.

9 4. Release the trigger to stop the motor. Allow the tool to come to aCOMPLETE STOP before turning it over and putting it down. ATTACHING AND CARE OF DUST BAG Attach the dust bag to the sander bypushing the dust bag tube into thesander vacuum housing (Fig. 4).F o r t h e m o s t e f f i c i e n t o...

Page 10 - Lift the tool from the work before turning the motor off.; FAST SANDING ON ROUGH WORK; R e a d a n d f o l l o w “; A D D I T I O N A L S A F E T Y R U L E S F O R; section of this manual.; SPECIAL SANDING PROCEDURES

10 9 5. Work back and forth over a fairly wide area to obtain an even surface. 6. Do not let the tool tilt. The edge of the belt can make a deep cuts into thesurface. 7. Do not pause in any one spot during the sanding operation. The belt willeat into the work and make the surface uneven. 8. Lift the...

Page 11 - BE CAREFUL; when sanding at the; SANDING METAL

11 DOORS AND MILL WORK When sanding doors, cabinet frames, sash, storm windows and screens, takecare to avoid working into the cross grain where one member meets another.Notice that the right edge of the belt is visible on the sander. Work carefullyalong the edge where the rail meets the stile. If t...

Page 12 - KEEP TOOL CLEAN; Wear safety glasses while using compressed air.; FAILURE TO START; MAINTENANCE

12 KEEP TOOL CLEAN Periodically blow out all air passages with dry compressed air. All plastic partsshould be cleaned with a soft damp cloth. NEVER use solvents to cleanplastic parts. They could possibly dissolve or otherwise damage the material. Wear safety glasses while using compressed air. FAILU...

Page 13 - ACCESSORIES; for a catalog or for the name of your nearest

13 ACCESSORIES A complete line of accessories is available from your Porter-Cable ·Delta Supplier, Porter-Cable · Delta Factory Service Centers, andPorter-Cable Authorized Service Stations. Please visit our Web Site www.porter-cable.com for a catalog or for the name of your nearest supplier. Since a...

Page 14 - ONE YEAR WARRANTY

14 PORTER-CABLE LIMITED ONE YEAR WARRANTY Porter-Cable warrants its Professional Power Tools for a period of one year from the date of originalpurchase. We will repair or replace at our option, any part or parts of the product and accessoriescovered under this warranty which, after examination, prov...

Page 15 - PORTER-CABLE • DELTA SERVICE CENTERS

The following are trademarks of PORTER-CABLE • DELTA (Las siguientes son marcas registradas de PORTER-CABLE • DELTA S.A.) (Les marques suivantes sont des marques de fabriquant de la PORTER-CABLE • DELTA): Auto-Set ® , BAMMER ® , B.O.S.S. ® , Builder’s Saw ® , Contractor’s Saw ® , Contractor’s Saw II...