Page 2 - SprintScan 45i
SprintScan 45i System Requirements . . . . . . . . . . . . . . 3 Unpack the Box . . . . . . . . . . . . . . . . . . . 4 Position the Scanner . . . . . . . . . . . . . . . 5 Install the Software . . . . . . . . . . . . . . . . . 5 Connect the Scanner to the Computer . . . . . . . . . . . . . . . . . ...
Page 3 - System Requirements
English 3 System Requirements Macintosh Systems • A Power Macintosh family computer or compatible, with a PowerPC processor and 32 megabytes (MB) of RAM. • Apple system software version 7.6 or later. • ColorSync color management software version 2.5 or later (required for color profile embedding). •...
Page 4 - Unpack the Box
English 4 1 Unpack the Box Make sure you have all the following components. Contact your dealer if any is missing or damaged. a Scanner b Power cable c This manual d Pass-through terminator e SCSI cable (25-pin to 50-pin) f Film carrier for 4x5 film g Adapter for 120 film, 2¼ x 2¼ in. h Adapter for ...
Page 5 - Position the Scanner
English 5 2 Position the Scanner Place the scanner on a flat, stable surface, free of vibration. Leave at least 2 inches (50mm) of space around all sides and the top of the scanner for adequate ventilation, and leave room at the back to reach the power switch on the rear panel. Caution: As with any ...
Page 6 - Connect the Scanner to
English 6 4 Connect the Scanner to the Computer The SprintScan 45i requires a SCSI host adapter in your com-puter. If your computer does not have an adapter, you must install one (see page 17). If your computer is a PC-compatible with a SCSI adapter, but the adapter is connected to a hard drive or C...
Page 9 - Connect the Scanner to
English 9 5 Connect the Scanner to AC Power and Turn On 1 Connect the power cord as shown. 2 Turn on the scanner by pressing the power switch. 3 Check the lights. The green light indicates power on. The yellow light blinks while the scanner initializes, remaining steady when the scanner is ready. (T...
Page 10 - Loading the Film Carriers
English 10 6 Loading the Film Carriers The Four-Slide Film Carrier 1 With the text facing up and the hinge at the top, open the carrier flat as shown. 2 Place up to four mounted 35mm slides in the spaces pro-vided. Be sure the slide mounts fit properly in the recessed areas. The images should be rig...
Page 14 - Inserting the Carrier into the
English 14 7 Inserting the Carrier into the Scanner 1 Open the carrier access door. 2 Insert the carrier gently and firmly into the carrier slot as shown, until you feel it stop. 3 Close the carrier access door. The scanner will not scan if the door is open. Note: Do not open the carrier access door...
Page 15 - Preview-Scan an Image
English 15 8 Preview-Scan an Image 1 Load the film or slide into the film carrier (as described previously). 2 Insert the carrier into the scanner (as described previously). 3 Start the PolaColor Insight program: 4 Select the type of slide or negative you are scanning from the Input list on the Prev...
Page 16 - Enhance and Final-Scan the; 0 Remove the Carrier
English 16 9 Enhance and Final-Scan the Image Follow the online user’s guide instructions to enhance the image and perform a final scan. To view the online PolaColor Insight User’s Guide : 10 Remove the Carrier 1 When the scan is complete, open the door and remove the carrier. Remove the film and st...
Page 17 - Installing a SCSI Host Adapter
English 17 Installing a SCSI Host Adapter The SprintScan 45i connects to a SCSI host adapter in your com-puter. Most Macintosh computers have a SCSI adapter built in, but most IBM PC compatible computers do not. If you must install a SCSI adapter, turn the computer off and fol-low instructions provi...
Page 18 - Radio and Television Interference
English 18 Radio and Television Interference FCC Notice (U.S.A.) Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable pro-tection against harmful interference in a ...