Peerless SP 850P - Manuals - manualsarea.com

Page 2 - WARNING; Table of Contents

2 of 10 ISSUED: 10-12-05 SHEET #: 202-9038-6 05-19-07 Note: Read entire instruction sheet before you start installation and assembly. For customer care call (800) 729-0307 or (708) 865-8870. • Do not begin to install your Peerless product until you have read and understood the instructions and warni...

Page 3 - Parts List; Snap installation tab off of wall mount assembly (; CC; AA

3 of 10 ISSUED: 10-12-05 SHEET #: 202-9038-6 05-19-07 SP850 SP850P SP850-S SP850P-S De scription Qty. Pa rt # Pa rt # Pa rt # Pa rt # A wall mount assembly 1 201-0385 201-0386 201-0383 201-0384 B locking tab 1 200-1871 200-1871 200-4871 200-4871 C .219 ID x .5 OD x .125H spacer 1 540-1032 540-1032 5...

Page 4 - Installation to Wood Stud Wall; • Tighten wood screws so that wall plate is firmly; hardware and components.; point 1; to step 3 on page 6.

4 of 10 ISSUED: 10-12-05 SHEET #: 202-9038-6 05-19-07 A Installation to Wood Stud Wall • Tighten wood screws so that wall plate is firmly attached, but do not overtighten. Overtightening candamage the screws, greatly reducing their holdingpower. • Never tighten in excess of 80 in. • lb (9 N.M.). • M...

Page 5 - Installation to Solid Concrete and Cinder Block Wall; not

5 of 10 ISSUED: 10-12-05 SHEET #: 202-9038-6 05-19-07 Position wall mount assembly ( A ) at desired position on wall . Use wall mount assembly, making sure that it is level, as a template to mark holes. Drill four 1/4" (6 mm)dia. holes to a minimum depth of 2-1/2" (64 mm). Con-crete must be ...

Page 6 - Place installation tab over sliding arms of wall mount assembly (; Find the VESA; FOR INSTALLING TO VESA 100 MM, 200 MM HOLE PATTERN; FOR VESA 100 MOUNTING PATTERN:; Thread two M4 x 12 mm screws (; BB

6 of 10 ISSUED: 10-12-05 SHEET #: 202-9038-6 05-19-07 INSTALLATION TAB A SLIDING ARM Place installation tab over sliding arms of wall mount assembly ( A ) to lock them in place. 3 • If screws don't get three complete turns in the screen inserts or if screws bottom out and adapter plate is still not ...

Page 7 - FOR VESA 200 MOUNTING PATTERN:; Thread two retaining spacers (; Note; Thread two M10 x 15 mm screws (

7 of 10 ISSUED: 10-12-05 SHEET #: 202-9038-6 05-19-07 FOR VESA 200 MOUNTING PATTERN: Thread two M4 x 12 mm screws ( BB ), leaving .25" exposed thread, into top holes on back of screen. Hook screen onto mounting plate, and attach using two bottom M4 x 12 mm screws as shown in figures 4.3 and 4.4....

Page 8 - ° tilt; DD; D D

8 of 10 ISSUED: 10-12-05 SHEET #: 202-9038-6 05-19-07 fig. 8.1 fig. 8.2 5° tilt 10° tilt M6 SCREW MOUNTINGPLATE M6 SCREW MOUNTINGPLATE Slide one mesh sleeve ( F ) over each cable. Use cable ties ( G ) to tighten both ends of mesh sleeves to cables. Note: loop cable ties through cable mounts and tigh...

Page 9 - Screen not shown for clarity.

9 of 10 ISSUED: 10-12-05 SHEET #: 202-9038-6 05-19-07 Roll can be adjusted 1° clockwise orcounterclockwise. To adjust roll, loosen screen fasteners slightly,leaving them snug. Level screen, then tighten screenfasteners. NOTE: When adjusting roll, screws should be retightened as indicated in step 4. ...

Page 10 - Screen Compatibility Chart

10 of 10 ISSUED: 10-12-05 SHEET #: 202-9038-6 05-19-07 Screen Compatibility Chart Manufacturer Screen Manufacturer Model Size Apex 27" AVL-2776 Dell 26" W2600 Dell 30" W3000 Gateway 26" GTW-L26M103 Gateway 30" GTW-L30M103 Hewlett Packard 30" LC3040N Hyundai 26" HQL260WR H...