Paradyne 8785 - Manuals - manualsarea.com

Page 2 - Hotwire TDM SDSL Termination Units; Hotwire; Installation Overview; Installing the unit in the DSLAM.; Planning the Installation; Review the following list to help plan for the installation.

2 Hotwire TDM SDSL Termination Units Hotwire r 8775 and 8785 TDM SDSL Termination Units are circuit card assemblies comprising four Time Division Multiplexer Symmetric Digital Subscriber Line(TDM SDSL) ports and four synchronous ports. When the Hotwire 87xx TDM SDSLTermination Unit is used in a Hotw...

Page 3 - Cables You Need; For the network connection:

3 Cables You Need The following customer-provided cables are used with this product. For the network connection: H Plug-ended 50-position Telco cable for connection from the Hotwire DSLAM to theMain Distribution Frame (MDF) or other demarcation point. For the DTE connection, one of the following: H ...

Page 4 - Installing TDM SDSL Cards; HANDLING PRECAUTIONS FOR STATIC-SENSITIVE DEVICES; Procedure; Remove the filler plate from the installation slot.

496-15149 4 Installing TDM SDSL Cards A Hotwire TDM SDSL Termination Unit can be installed, removed, and replaced withoutdisrupting service to other cards in the chassis. ! HANDLING PRECAUTIONS FOR STATIC-SENSITIVE DEVICES This product is designed to protect sensitive components from damage due to e...

Page 5 - — For a Hotwire 8800 Series DSLAM – Hold the unit vertically, with the; mating connectors on the backplane.

5 — For a Hotwire 8800 Series DSLAM – Hold the unit vertically, with the component side facing right, and insert it into the top and bottom card guides. ALARMS Major Minor Fan B A POWER MCC SYSTEM OK Alm Test ETHE RNET TX RX Coll 99-16544 MGT SERIAL MGT10BT ALARM SLOTS 1 - 6 SLOTS 7-12 SLOTS 13-18 L...

Page 6 - Connecting to the DTE; To connect the Hotwire 87xx TDM SDSL Termination Unit to your DTE:; Connect the four terminating connectors to your DTE.; Connecting to an MDF; To connect the Hotwire DSLAM containing the unit to an MDF:; DSLAM; Not Applicable

6 Connecting to the DTE Connection to the four ports of the unit is through the 100-pin connector on itsfaceplate. Use one of the DTE cables listed under Cables You Need on page 3. " Procedure To connect the Hotwire 87xx TDM SDSL Termination Unit to your DTE: 1. Connect the 100-position connecto...

Page 7 - Ferrite Choke

7 2. If necessary to attach the cable connector firmly in place, replace the longer Telco cable captive screw with a shorter one. Fasten the connector. 3. Insert a cable tie (provided with Hotwire DSLAM) through the tie mount to hold the 50-position Telco connector in place. 4. Make sure the other e...

Page 8 - Front Panel LEDs; Type

8 Front Panel LEDs The following table describes the meaning and states of the LEDs on theHotwire 8775 or 8785 TDM SDSL Termination Unit’s faceplate. Type LED LED is . . .* Indicating . . . SYSTEM OK(Green) On Off Slow Cycling Pulsing Unit failure; system processing hasstopped. No power to card. Uni...

Page 10 - Entering Identity Information; Configuring the Unit; Main Menu

10 Entering Identity Information After accessing your unit for the first time, use the Change Identity screen to determineSNMP administrative system information that will be displayed on the Identity screen ofthe Status branch. To access the Card Identity screen, follow this menu selectionsequence: ...

Page 11 - Configuration Edit/Display; ÎÎ

11 Configuration Edit/Display The Configuration Edit/Display screen is displayed when the current, customer, ordefault configuration is loaded and allows groups of configuration options to bedisplayed. To access the Configuration Edit/Display screen, follow this menu selectionsequence: Main Menu → C...

Page 12 - Copyright

12 Warranty, Sales, Service, and Training Information Contact your local sales representative, service representative, or distributor directly forany help needed. For additional information concerning warranty, sales, service, repair,installation, documentation, training, distributor locations, or P...