Paradyne 4200 - Manuals - manualsarea.com

Page 2 - Notice

A August 2002 4200-A2-GB20-00 Copyright © 2002 Paradyne Corporation.All rights reserved.Printed in U.S.A. Notice This publication is protected by federal copyright law. No part of this publication may be copied or distributed, transmitted, transcribed, stored in a retrieval system, or translated int...

Page 3 - Contents; About This Guide; xvii; Introduction to the Hotwire 4200 GranDSLAM

4200-A2-GB20-00 August 2002 i Contents About This Guide Document Purpose and Intended Audience . . . . . . . . . . . . . . . . . . . . xvii Document Summary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . xvii Product-Related Documents . . . . . . . . . . . . . . . ...

Page 4 - ii

Contents ii August 2002 4200-A2-GB20-00 ACT-PROFILE-ADSLALM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-4 Response Format . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-4 Example . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ...

Page 5 - iii

Contents 4200-A2-GB20-00 August 2002 iii REPT ALM ADSL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-28 REPT EVT ADSL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-30 RTRV-ADSL . . . . . . . . . . . . . . . . . . . . . . ....

Page 6 - iv; DS1 Facility Commands

Contents iv August 2002 4200-A2-GB20-00 4 DS1 Facility Commands Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-1 ED-T1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-2 Response Format ....

Page 7 - Cross Connect Commands

Contents 4200-A2-GB20-00 August 2002 v ENT-PROFILE-TRAFDSC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-8 Response Format . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-8 Example . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ....

Page 8 - Equipment Commands

Contents vi August 2002 4200-A2-GB20-00 ENT-CRS-VC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-7 Response Format . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-8 Example . . . . . . . . . . . . . . . . . . . . . . . . . . . ....

Page 9 - vii; Performance Commands

Contents 4200-A2-GB20-00 August 2002 vii ED-IPPORT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-6 Response Format . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-7 Example . . . . . . . . . . . . . . . . . . . . . . . . . ....

Page 10 - viii; 0 Fault Commands

Contents viii August 2002 4200-A2-GB20-00 REPT-OPSTAT-VCL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-10 Response Format . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-10 Example . . . . . . . . . . . . . . . . . . . . . . . . . . . . ...

Page 11 - ix; 1 Log Commands

Contents 4200-A2-GB20-00 August 2002 ix RTRV-COND-ADSL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-28 Response Format . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-29 Example . . . . . . . . . . . . . . . . . . . . . . . . . . . . ....

Page 12 - 3 Synchronization Commands

Contents x August 2002 4200-A2-GB20-00 ED-PID . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12-6 Response Format . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12-6 Example . . . . . . . . . . . . . . . . . . . . . . . ...

Page 13 - xi; 4 System Commands

Contents 4200-A2-GB20-00 August 2002 xi 14 System Commands Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14-1 ACT-USER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14-2 Response Format . . . . ....

Page 14 - xii; 5 Test Commands

Contents xii August 2002 4200-A2-GB20-00 RTRV-META-CMD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14-21 Response Format . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14-21 Example . . . . . . . . . . . . . . . . . . . . . . . . . . . ....

Page 15 - xiii; A Error Codes

Contents 4200-A2-GB20-00 August 2002 xiii RLS-LPBK-VCL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15-9 Response Format . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15-9 Example . . . . . . . . . . . . . . . . . . . . . . . . . ....

Page 16 - xiv; C Traps and MIBs

Contents xiv August 2002 4200-A2-GB20-00 C Traps and MIBs SNMP Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C-1 Traps Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C-1 SNMP Traps . . . . . . . . . . ...

Page 17 - xv; D Hotwire 6390 ReachDSL Modem Download

Contents 4200-A2-GB20-00 August 2002 xv Paradyne ReachDSL MIB (pdn_reachDSL.mib) . . . . . . . . . . . . . . . . . C-45 Paradyne DS1 Config MIB (RFC 2495) . . . . . . . . . . . . . . . . . . . . . . . . C-46 Paradyne DS1 Extension MIB . . . . . . . . . . . . . . . . . . . . . . . . . . . . C-46 ...

Page 18 - xvi

Page 19 - Document Purpose and Intended Audience; Section

4200-A2-GB20-00 August 2002 xvii About This Guide Document Purpose and Intended Audience This guide contains information necessary for the use of the GranDSLAM 4200 ATM Stackable DSLAM. The successful user of this manual has some experience with the installation and configuration of DSL network devi...

Page 20 - xviii; Product-Related Documents; Library

About This Guide xviii August 2002 4200-A2-GB20-00 A master glossary of terms and acronyms used in Paradyne documents is available online at www.paradyne.com. Select Library → Technical Manuals → Technical Glossary . Product-Related Documents Complete documentation for this product is available onli...

Page 21 - xix; To order a paper copy of a Paradyne document:

About This Guide 4200-A2-GB20-00 August 2002 xix To order a paper copy of a Paradyne document: Within the U.S.A., call 1-800-PARADYNE (1-800-727-2396) Outside the U.S.A., call 1-727-530-8623

Page 22 - xx

Page 23 - Overview; GranDSLAM 4200 ATM Stackable DSLAM

4200-A2-GB20-00 August 2002 1-1 1 Introduction to the Hotwire 4200 GranDSLAM Overview The GranDSLAM™ 4200 ATM Stackable DSLAM is a stackable DSLAM designed for installation in the Central Office (CO) environment or in a standalone configuration for small deployments. It is available with or without ...

Page 24 - shows a typical application for the GranDSLAM 4200.; GranDSLAM 4200 Sample Application

1. Introduction to the Hotwire 4200 GranDSLAM 1-2 August 2002 4200-A2-GB20-00 Figure 1-2 shows a typical application for the GranDSLAM 4200. Figure 1-2. GranDSLAM 4200 Sample Application ReachDS L TST LINE ETHER NET ALM PWR TX/RX 1 12 13 24 DSL PORTS 1-2 4 POTS 1-24 4 8 16 20 POWER A ALARM RTN -48VD...

Page 25 - Features

1. Introduction to the Hotwire 4200 GranDSLAM 4200-A2-GB20-00 August 2002 1-3 Features The GranDSLAM 4200 DSLAM has the following features: Compact size (height = 1U) Shelf-mountable (up to five units high) and rack-mountable Low price per port Up to 24 por ts per unit Up to 120 por ts per...

Page 27 - Using the Command Line Interface; Display system status; TL1 Command Language; The TL1 command is in the following general format:

4200-A2-GB20-00 August 2002 2-1 2 Using the Command Line Interface Overview The Command Line Interface (CLI) is accessible via either a directly connected terminal session or a Telnet connection. You can use the CLI to: Change the operational characteristics of the device by setting configuration ...

Page 28 - Command Code; The command code consists of a verb and one or more modifiers.; TL1 Command Code Components

2. Using the Command Line Interface 2-2 August 2002 4200-A2-GB20-00 Command Code The command code consists of a verb and one or more modifiers. Table 2-1. TL1 Command Code Components Command Code Component Component Examples Command Examples Verb signifies action to be performed. ACT (Activate) ...

Page 29 - Parameters; Staging parameters; Output Messages; Error Codes

2. Using the Command Line Interface 4200-A2-GB20-00 August 2002 2-3 Parameters Parameters are values which clarify the function of a command. Parameter syntax must be followed exactly to avoid system error responses. There are two types of parameters: Staging parameters − Designate where the verb ...

Page 30 - Command Entry Features

2. Using the Command Line Interface 2-4 August 2002 4200-A2-GB20-00 Command Entry Features The GranDSLAM 4200 uses Transaction Language No. 1 (TL1) language for CLI commands and messages. These commands and messages are used to configure and maintain the system. TL1 offers the following features to ...

Page 31 - Command query. You can obtain help with CLI commands by typing a; the CLI lists all the possible RTRV commands.; User Access Privilege Levels; CLI users have one of three user access privilege levels:; SUPER – The user has access to all commands (supervisor level).; Logging In; The ACT-USER command logs a user in and begins a user session. See; System Commands; for more information.

2. Using the Command Line Interface 4200-A2-GB20-00 August 2002 2-5 Command query. You can obtain help with CLI commands by typing a ? (question mark). A question mark alone lists all commands. For example, if you enter: RTRV ? the CLI lists all the possible RTRV commands. Command history. Press...

Page 32 - GranDSLAM 4200 Turn-up Procedure; Out-of-Band Management – Operates over the Ethernet interface.

2. Using the Command Line Interface 2-6 August 2002 4200-A2-GB20-00 GranDSLAM 4200 Turn-up Procedure You can turn up your GranDSLAM 4200 through the Ethernet connection via a PC or terminal connected to the unit’s CONSOLE port. Then using a series of TL1 commands or an NMS system such as Paradyne’s ...

Page 33 - Turn-up Procedure for Inband Management; IP Access Commands; Procedure

2. Using the Command Line Interface 4200-A2-GB20-00 August 2002 2-7 Turn-up Procedure for Inband Management Procedure To turn up the GranDSLAM 4200 using inband management: 1. Manual Mode: At the unit, configure the IP address, net mask, and next-hop router. DHCP Mode: Set the ATM1 physical address ...

Page 34 - Configuring the Unit for Operation; Additional Configuration Commands; GranDSLAM 4200 Configuration Commands; GrandVIEW EMS 3.0 User’s Guide

2. Using the Command Line Interface 2-8 August 2002 4200-A2-GB20-00 5. Enable security for your GranDSLAM 4200 unit. Using the TL1 command ENT-USER-SECU, change the default login and password. Use the EMS to configure SNMP community strings, the SYSLOG server, and trap managers. 6. Change the time, ...

Page 37 - ADSL Facility Commands; This chapter contains the following ADSL Facility commands:; REPT ALM ADSL

4200-A2-GB20-00 August 2002 3-1 3 ADSL Facility Commands Overview This chapter contains the following ADSL Facility commands: ACT-PROFILE-ADSL on page 3-2 ACT-PROFILE-ADSLALM on page 3-4 DLT-PROFILE-ADSL on page 3-6 DLT-PROFILE-ADSLALM on page 3-8 ED-ADSL on page 3-10 ED-PROFILE-ADSLDN o...

Page 38 - on page 3-24 for information on how to create a new ADSL; Response Format; IP c; After the above response, a new command input may be generated.

3. ADSL Facility Commands 3-2 August 2002 4200-A2-GB20-00 ACT-PROFILE-ADSL The ACT-PROFILE-ADSL command activates newly created ADSL profiles. See ENT-PROFILE-ADSL on page 3-24 for information on how to create a new ADSL profile. Response Format If, in less than 2 seconds, a normal or error response...

Page 39 - Parameter Explanation

3. ADSL Facility Commands 4200-A2-GB20-00 August 2002 3-3 Example Activate profile 6. ACT-PROFILE-ADSL:TAMPA:6:42; TAMPA 01-11-24 12:30:43M 42 COMPLD /* ACT-PROFILE-ADSL:TAMPA:6:42 */; Related Commands DLT-PROFILE-ADSL on page 3-6 ED-PROFILE-ADSLDN on page 3-14 ED-PROFILE-ADSLUP on page 3-19 ENT-PRO...

Page 40 - on page 3-26 for information on how to

3. ADSL Facility Commands 3-4 August 2002 4200-A2-GB20-00 ACT-PROFILE-ADSLALM The ACT-PROFILE-ADSLALM command activates newly created ADSL alarm profiles. See ENT-PROFILE-ADSLALM on page 3-26 for information on how to create a new ADSL alarm profile. Response Format If, in less than 2 seconds, a nor...

Page 49 - Example

3. ADSL Facility Commands 4200-A2-GB20-00 August 2002 3-13 Example Edit rack 1, shelf 1, slot 1, circuit 20 to have an ADSL line profile of 4 and be in service. ED-ADSL:TAMPA:ADSL-1-1-1-20:42:::ADSLPROF=4:PST=IS; TAMPA 01-10-20 11:32:43M 42 COMPLD /* ED-ADSL:TAMPA:ADSL-1-1-1-20:42:::ADSLPROF=4:PST=I...

Page 50 - on page 3-24 for information on how to create a

3. ADSL Facility Commands 3-14 August 2002 4200-A2-GB20-00 ED-PROFILE-ADSLDN The ED-PROFILE-ADSLDN command enables you to edit ADSL line configuration parameters for the downstream direction (from ATU-C to ATU-R) in an ADSL Profile. See ENT-PROFILE-ADSL on page 3-24 for information on how to create ...

Page 52 - information on how to create a new ADSL alarm profile.

3. ADSL Facility Commands 3-16 August 2002 4200-A2-GB20-00 ED-PROFILE-ADSLDNALM The ED-PROFILE-ADSLDNALM command enables you to edit ADSL alarm line configuration parameters for the downstream direction (from ATU-C to ATU-R) in an ADSL Alarm Profile. See ENT-PROFILE-ADSLALM on page 3-26 for informat...

Page 53 - Edit profile 6 to have an Errored Seconds threshold of 2.

3. ADSL Facility Commands 4200-A2-GB20-00 August 2002 3-17 Response Format If, in less than 2 seconds, a normal or error response cannot be sent, the following acknowledgment response is sent: IP c After the above response, a new command input may be generated. Normal Response: sid yy-mm-dd hh:mm:ss...

Page 54 - Related Commands

3. ADSL Facility Commands 3-18 August 2002 4200-A2-GB20-00 Related Commands ENT-PROFILE-ADSLALM on page 3-26 RTRV-PROFILE-ADSLDNALM on page 3-47

Page 55 - on page 3-24 for information on how to create a new

3. ADSL Facility Commands 4200-A2-GB20-00 August 2002 3-19 ED-PROFILE-ADSLUP The ED-PROFILE-ADSLUP command enables you to edit ADSL line configuration parameters for the upstream direction (from ATU-R to ATU-C) in an ADSL Profile. See ENT-PROFILE-ADSL on page 3-24 for information on how to create a ...

Page 56 - Edit profile 6 to have a Target Noise Margin of 10 dB.

3. ADSL Facility Commands 3-20 August 2002 4200-A2-GB20-00 Error Response: sid yy-mm-dd hh:mm:ssM c DENY /* ED-PROFILE-ADSLUP:[tid]:adsl_profile_id:[ctag]:::[adslprof_nblk] */ errcde; Example Edit profile 6 to have a Target Noise Margin of 10 dB. ED-PROFILE-ADSLUP:TAMPA:6:42:::TNMR=10; TAMPA 02-07-2...

Page 59 - Edit profile 6 to have an Severely Errored Seconds threshold of 8.

3. ADSL Facility Commands 4200-A2-GB20-00 August 2002 3-23 Example Edit profile 6 to have an Severely Errored Seconds threshold of 8. ED-PROFILE-ADSLUPALM:TAMPA:6:42:::SES-L=8; TAMPA 02-07-24 12:30:43M 42 COMPLD /* ED-PROFILE-ADSLUPALM:TAMPA:6:42:::SES-L=8; */ ; Related Commands ACT-PROFILE-ADSLALM ...

Page 61 - Configure profile 6 with a profile name of TAMPA201.

3. ADSL Facility Commands 4200-A2-GB20-00 August 2002 3-25 Error Response: sid yy-mm-dd hh:mm:ssM c DENY /* ENT-PROFILE-ADSL:[tid]:adsl_profile_id:[ctag]:: profile_name */ aid:ERRCDE=errcde /* error description */; Example Configure profile 6 with a profile name of TAMPA201. ENT-PROFILE-ADSL:TAMPA:6...

Page 62 - Allocate a new profile with

3. ADSL Facility Commands 3-26 August 2002 4200-A2-GB20-00 ENT-PROFILE-ADSLALM The ENT-PROFILE-ADSLALM command allocates a new ADSL alarm configuration profile. A new ADSL alarm profile is created using the following steps: 1. Allocate a new profile with ENT-PROFILE-ADSLALM . 2. Configure downstream...

Page 66 - REPT EVT ADSL

3. ADSL Facility Commands 3-30 August 2002 4200-A2-GB20-00 REPT EVT ADSL The REPT EVT ADSL message reports current events associated with an ADSL facility on an LT. Table 3-24. REPT EVT ADSL Message Parameters (1 of 2) almcode atag REPT EVT ADSL aid_adsl:cond_adsl,[condeff], [ocrdat],[ocrtm],[locn],...

Page 72 - None

3. ADSL Facility Commands 3-36 August 2002 4200-A2-GB20-00 Example Retrieve ATU-R configuration data for rack 1, shelf 1, slot 1, circuit 9. RTRV-ATUR:TAMPA:ATUR-1-1-1-9:42::::; TAMPA 02-03-24 12:30:43M 42 COMPLD /* RTRV-ATUR:TAMPA:ATUR-1-1-1-9:42:::: */ ATUR-1-1-1-9,R1.01:01; Related Commands None ...

Page 79 - Retrieve alarm profile 5.

3. ADSL Facility Commands 4200-A2-GB20-00 August 2002 3-43 Example Retrieve alarm profile 5. RTRV-PROFILE-ADSLALM:TAMPA:5:42; TAMPA 02-07-24 12:30:43M 42 COMPLD /* RTRV-PROFILE-ADSLALM:TAMPA:5:42 */ 5:LOCAL:TAMPA101:CONFIG; Related Commands ACT-PROFILE-ADSLALM on page 3-4 DLT-PROFILE-ADSLALM on page...

Page 80 - information on how to create a new ADSL profile.

3. ADSL Facility Commands 3-44 August 2002 4200-A2-GB20-00 RTRV-PROFILE-ADSLDN The RTRV-PROFILE-ADSLDN command enables you to retrieve ADSL line configuration parameters associated with the downstream direction (from ATU-C to ATU-R) in an ADSL Profile. See ED-PROFILE-ADSLDN on page 3-14 for informat...

Page 93 - This chapter contains the following DS1 Facility commands:; REPT ALM T1

4200-A2-GB20-00 August 2002 4-1 4 DS1 Facility Commands Overview This chapter contains the following DS1 Facility commands: ED-T1 on page 4-2 ENT-T1 on page 4-5 REPT ALM T1 on page 4-8 REPT EVT T1 on page 4-9 REPT-OPSTAT-T1 on page 4-10 RTRV-PM-T1 on page 4-12 RTRV-T1 on page 4-15

Page 96 - Edit circuit 1 on the NT to have a line interface type of T1.; ED-T1 Command Parameters

4. DS1 Facility Commands 4-4 August 2002 4200-A2-GB20-00 Example Edit circuit 1 on the NT to have a line interface type of T1. ED-T1:TAMPA:NTT1-1:42:::LINETYPE=T1; TAMPA 00-11-24 12:30:43M 42 COMPLD /* ED-T1:TAMPA:NTT1-1:42:::LINETYPE=T1 */; Related Commands ENT-T1 on page 4-5 RTRV-T1 on page 4-15 T...

Page 98 - Normal Response; T1 Line Equalization Values

4. DS1 Facility Commands 4-6 August 2002 4200-A2-GB20-00 Response Format If, in less than 2 seconds, a normal or error response cannot be sent, the following acknowledgment response is sent: IP c After the above response, a new command input may be generated. Normal Response sid yy-mm-dd hh:mm:ssM c...

Page 99 - Error Response; Enter circuit 1 on the NT with a line interface type of T1.; ENT-T1 Response Parameters

4. DS1 Facility Commands 4200-A2-GB20-00 August 2002 4-7 Error Response sid yy-mm-dd hh:mm:ssM c DENY /* ENT-T1:[tid]:aid_ds1:[ctag]:::ds1_nblk:[pst] */ aid:ERRCDE=errcde /* error description */; Example Enter circuit 1 on the NT with a line interface type of T1. ENT-T1:TAMPA:NTT1:42:::LINETYPE=T1; ...

Page 100 - REPT ALM T1 Response Parameters

4. DS1 Facility Commands 4-8 August 2002 4200-A2-GB20-00 REPT ALM T1 The REPT ALM T1 message reports current T1 (DS1) facility alarms from the NE. Table 4-6. REPT ALM T1 Response Parameters almcode atag REPT ALM T1 "aid_ds1:ntfncde,cond_ds1, serveff,[ocrdat],[ocrtm],[locn],[dirn]:[cond_descr]...

Page 101 - REPT EVT T1; REPT EVT T1 Response Parameters

4. DS1 Facility Commands 4200-A2-GB20-00 August 2002 4-9 REPT EVT T1 The REPT EVT T1 message repor ts current T1 (DS1) facility events from the NE. Table 4-7. REPT EVT T1 Response Parameters almcode atag REPT EVT T1 "aid_ds1:ntfncde,cond_ds1, serveff,[ocrdat],[ocrtm],[locn],[dirn]:[cond_descr]&#...

Page 103 - Repor t DS1 facility operational parameters for NTT1-3.

4. DS1 Facility Commands 4200-A2-GB20-00 August 2002 4-11 Example Repor t DS1 facility operational parameters for NTT1-3. REPT-OPSTAT-T1:TAMPA:NTT1-1; TAMPA 01-11-24 12:30:43M 42 COMPLD /* REPT-OPSTAT-T1:TAMPA:NTT1-1:42 */"NTT1-3:INCELLS,35500""NTT1-3:OUTCELLS,23300"; Related Command...

Page 104 - The RTRV-PM-T1 command retrieves DS1 performance monitoring data.

4. DS1 Facility Commands 4-12 August 2002 4200-A2-GB20-00 RTRV-PM-T1 The RTRV-PM-T1 command retrieves DS1 performance monitoring data. Table 4-10. RTRV-PM-T1 Command Parameters (1 of 2) RTRV-PM-T1:[tid]:aid_ds1:[ctag]::[monds1],[monlev],[locn],,[tmper],[mondat],[montm]; Restrictions: All parameters ...

Page 110 - Retrieve configuration data for circuit 1 on the NT.

4. DS1 Facility Commands 4-18 August 2002 4200-A2-GB20-00 Example Retrieve configuration data for circuit 1 on the NT. RTRV-T1:TAMPA:NTT1-1:42::::; TAMPA 01-11-24 12:30:43M 42 COMPLD /* RTRV-T1:TAMPA:NTT1-1:42:::: */ NTT1-1::LINETYPE=DSX1,LBO=0,EQLZ=0:IS-NR; Related Commands ED-T1 on page 4-2 ENT-T1...

Page 111 - ATM Commands; This chapter contains the following other commands:

4200-A2-GB20-00 August 2002 5-1 5 ATM Commands Overview This chapter contains the following other commands: DLT-PROFILE-TRAFDSC on page 5-2 DLT-VCL on page 5-4 ED-ATMPORT on page 5-6 ENT-PROFILE-TRAFDSC on page 5-8 ENT-VCL on page 5-10 RTRV-ATMPORT on page 5-13 RTRV-PROFILE-ATMACC on p...

Page 113 - Delete traffic descriptor profile 5.

5. ATM Commands 4200-A2-GB20-00 August 2002 5-3 Example Delete traffic descriptor profile 5. DLT-PROFILE-TRAFDSC:TAMPA:5:42; TAMPA 01-11-24 12:30:43M 42 COMPLD /* DLT-PROFILE-TRAFDSC:TAMPA:5:42 */; Related Commands ENT-PROFILE-TRAFDSC on page 5-8 RTRV-PROFILE-TRAFDSC on page 5-19 Table 5-2. DLT-PROF...

Page 114 - DLT-VCL Command Parameters

5. ATM Commands 5-4 August 2002 4200-A2-GB20-00 DLT-VCL The DLT-VCL command deletes selected ATM interface Vir tual Channel Links (VCL) that are not in use. Response Format If, in less than 2 seconds, a normal or error response cannot be sent, the following acknowledgment response is sent: IP c Afte...

Page 115 - Delete the VCL for Virtual Path 15.; DLT-VCL Response Parameters

5. ATM Commands 4200-A2-GB20-00 August 2002 5-5 Error Response: sid yy-mm-dd hh:mm:ssM c DENY /* DLT-VCL:[tid]:aid_vcl:[ctag][:] */ aid:ERRCDE=errcde /* error description */; Example Delete the VCL for Virtual Path 15. DLT-VCL:TAMPA:NTVCL-15:42; TAMPA 01-11-24 12:30:43M 42 COMPLD /* DLT-VCL:TAMPA:NT...

Page 116 - ED-ATMPORT Command Parameters

5. ATM Commands 5-6 August 2002 4200-A2-GB20-00 ED-ATMPORT The ED-ATMPORT command edits configuration data associated with an ATM por t in the NE. Response Format If, in less than 2 seconds, a normal or error response cannot be sent, the following acknowledgment response is sent: IP c After the abov...

Page 117 - ED-ATMPORT Response Parameters

5. ATM Commands 4200-A2-GB20-00 August 2002 5-7 Example Edit rack 1, shelf 1, slot 1, circuit 9 to have an OAM segment location ID of all ones. ED-ATMPORT:TAMPA:LTATM-1-1-1-9:42:::SEGID=ALLONES TAMPA 01-11-24 12:30:43M 42 COMPLD /* ED-ATMPORT:TAMPA:LTATM-1-1-1-9:42:::SEGID=ALLONES */; Related Comman...

Page 120 - ENT-VCL Command Parameters

5. ATM Commands 5-10 August 2002 4200-A2-GB20-00 ENT-VCL The ENT-VCL command creates an ATM interface Virtual Channel Links (VCL) on an NT or LT. Table 5-9. ENT-VCL Command Parameters ENT-VCL:[tid]:aid_vcl:[ctag]::[rcv_trafdsc],[xmt_trafdsc],[rcv_trafdscnm],[xmt_trafdscnm]; RESTRICTIONS: All paramet...

Page 128 - Retrieve parameters for profile 6.

5. ATM Commands 5-18 August 2002 4200-A2-GB20-00 Example Retrieve parameters for profile 6. RTRV-PROFILE-ATMACC:TAMPA:6:42::,LOCAL; TAMPA 01-11-24 12:30:43M 42 COMPLD /* RTRV-PROFILE-ATMACC:TAMPA:6:42::,LOCAL */ 6:LOCAL:TAMPA101:MAXVPCS=0,MAXVCCS=4,VPIBITS=1,VCIBITS=6 ; Related Commands None

Page 133 - Retrieve VCL for vir tual path 15, virtual channel 307.

5. ATM Commands 4200-A2-GB20-00 August 2002 5-23 Example Retrieve VCL for vir tual path 15, virtual channel 307. RTRV-VCL:TAMPA:NTVCL-15-307:42; TAMPA 01-11-24 12:30:43M 42 COMPLD /* RTRV-VCL:TAMPA:NTVCL-15-307:42 */ NTVCL-15-307:78,66:IS_NR ; Related Commands ED-ATMPORT on page 5-6

Page 135 - This chapter contains the following CrossConnect commands:; Cross-Connection Defaults

4200-A2-GB20-00 August 2002 6-1 6 Cross Connect Commands Overview This chapter contains the following CrossConnect commands: DLT-CRS-VC on page 6-2 ED-CRS-VC on page 6-4 ENT-CRS-VC on page 6-7 RTRV-CRS-VC on page 6-10 Cross-Connection Defaults The default uplink cross connections star t with...

Page 147 - This chapter contains the following Equipment commands:; REPT ALM EQPT

4200-A2-GB20-00 August 2002 7-1 7 Equipment Commands Overview This chapter contains the following Equipment commands: ED-EQPT on page 7-2 REPT ALM EQPT on page 7-4 REPT EVT EQPT on page 7-5 RTRV-EQPT on page 7-6 RTRV-INV-EQPT on page 7-9

Page 148 - ED-EQPT Command Parameters

7. Equipment Commands 7-2 August 2002 4200-A2-GB20-00 ED-EQPT The ED-EQPT command edits configuration data associated with equipment suppor ted by the system. Response Format If, in less than 2 seconds, a normal or error response cannot be sent, the following acknowledgment response is sent: IP c Af...

Page 149 - ED-EQPT Response Parameters

7. Equipment Commands 4200-A2-GB20-00 August 2002 7-3 Error Response: sid yy-mm-dd hh:mm:ssM c DENY /* ED-EQPT:[tid]:aid_eqpts:[ctag]::[eqpt_nblk]:[pst] */ aid:ERRCDE=errcde /* error description */; Example Edit ACU unit in rack 1, shelf 1 to be In-Service. ED-EQPT:TAMPA:ACU-1-1:42::::IS; TAMPA 01-1...

Page 150 - The REPT ALM EQPT message reports current alarms from the NE.; REPT ALM EQPT Message Parameters

7. Equipment Commands 7-4 August 2002 4200-A2-GB20-00 REPT ALM EQPT The REPT ALM EQPT message reports current alarms from the NE. Table 7-3. REPT ALM EQPT Message Parameters almcde atag REPT ALM EQPT aid_eqpts:ntfcde,cond_eqpt, srveff,[ocrdat],[ocrtm]: [conddescr]; almcde Alarm code. Identifies the ...

Page 151 - REPT EVT EQPT; REPT EVT EQPT Message Parameters

7. Equipment Commands 4200-A2-GB20-00 August 2002 7-5 REPT EVT EQPT The REPT EVT EQPT message repor ts current equipment events from the NE. Table 7-4. REPT EVT EQPT Message Parameters almcde atag REPT EVT EQPTaid_eqpt:cond_eqpt,[condeff], [ocrdat],[ocrtm]:[conddescr]; almcde Alarm code. Identifies ...

Page 152 - RTRV-EQPT Command Parameters

7. Equipment Commands 7-6 August 2002 4200-A2-GB20-00 RTRV-EQPT The RTRV-EQPT command retrieves configuration data associated with a unit of equipment. Response Format If, in less than 2 seconds, a normal or error response cannot be sent, the following acknowledgment response is sent: IP c After the...

Page 154 - Retrieve configuration data associated with Shelf 1.

7. Equipment Commands 7-8 August 2002 4200-A2-GB20-00 Example Retrieve configuration data associated with Shelf 1. RTRV-EQPT:TAMPA:SHELF-1-1:42; TAMPA 01-11-24 12:30:43M 42 COMPLD SHELF-1-1:NONE:NONE:,,:IS-NR, /* RTRV-EQPT:TAMPA:SHELF-1-1:42 */; Related Commands ED-EQPT on page 7-2

Page 157 - Retrieve inventory for Shelf 1.

7. Equipment Commands 4200-A2-GB20-00 August 2002 7-11 Example Retrieve inventory for Shelf 1. RTRV-INV-EQPT:TAMPA:SHELF-1-1:42::; TAMPA 02-08-06 12:30:43M 42 COMPLD SHELF-1-1:ALTS-A,PARADYNE,,,,, /* RTRV-INV-EQPT:TAMPA:SHELF-1-1:42 */; Related Commands None

Page 159 - This chapter contains the following IP Access commands:

4200-A2-GB20-00 August 2002 8-1 8 IP Access Commands Overview This chapter contains the following IP Access commands: DLT-ATMARPENT on page 8-2 DLT-IPPORT on page 8-4 ED-IPPORT on page 8-6 ENT-ATMARPENT on page 8-9 ENT-IPPORT on page 8-11 REPT-OPSTAT-IPPORT on page 8-14 RTRV-ATMARPENT ...

Page 160 - DLT-ATMARPENT Command Parameters

8. IP Access Commands 8-2 August 2002 4200-A2-GB20-00 DLT-ATMARPENT The command DLT-ATMARPENT deletes entries in the ATM Address Resolution Protocol table. Response Format If, in less than 2 seconds, a normal or error response cannot be sent, the following acknowledgment response is sent: IP c After...

Page 161 - DLT-ATMARPENT Response Parameters

8. IP Access Commands 4200-A2-GB20-00 August 2002 8-3 Example Delete the entry for ATM-2 por t with IP address 123.201.143.71. DLT-ATMARPENT:TAMPA:ATM-2:42::123.201.143.71; TAMPA 01-11-24 12:30:43M 42 COMPLD /* DLT-ATMARPENT:TAMPA:ATM-2:42::123.201.143.71 */; Related Commands ENT-IPPORT on page 8-11...

Page 162 - DLT-IPPORT Command Parameters

8. IP Access Commands 8-4 August 2002 4200-A2-GB20-00 DLT-IPPORT The command DLT-IPPORT deletes an Internet Protocol por t (or interface) in the NE. All entries in the ATM Address Resolution Protocol table for a IP port must be deleted ( DLT-ATMARPENT on page 8-2) before the por t can be deleted. Re...

Page 163 - DLT-IPPORT Response Parameters

8. IP Access Commands 4200-A2-GB20-00 August 2002 8-5 Example Delete ATM-2 port. DLT-IPPORT:TAMPA:ATM-2:42; TAMPA 01-11-24 12:30:43M 42 COMPLD /* DLT-IPPORT:TAMPA:ATM-2:42 */; Related Commands DLT-ATMARPENT on page 8-2 ENT-IPPORT on page 8-11 ED-IPPORT on page 8-6 ENT-ATMARPENT on page 8-9 RTRV-IPPO...

Page 166 - ED-IPPORT Response Parameters

8. IP Access Commands 8-8 August 2002 4200-A2-GB20-00 Example Configure the SLIP port with a configuration mode of BOOTP and a physical address of 18-00-42-49-09-03-27-22. ED-IPPORT:TAMPA:SLIP:42::BOOTP:PHYADDR="18-00-42-49-09-03-27-22"; TAMPA 01-11-24 12:30:43M 42 COMPLD /* ED-IPPORT:TAMPA:...

Page 167 - ENT-ATMARPENT Command Parameters

8. IP Access Commands 4200-A2-GB20-00 August 2002 8-9 ENT-ATMARPENT The command ENT-ATMARPENT defines a new entry in the ATM Address Resolution Protocol table in the NE. Response Format If, in less than 2 seconds, a normal or error response cannot be sent, the following acknowledgment response is se...

Page 168 - ENT-ATMARPENT Response Parameters

8. IP Access Commands 8-10 August 2002 4200-A2-GB20-00 Error Response: sid yy-mm-dd hh:mm:ssM c DENY; /* ENT-ATMARPENT:[tid]:aid_ipport:[ctag]::ip_addr,[vpi],[vci] */ aid:ERRCDE=errcde /* error description */; Example Define a new entr y for ATM-2 port with IP address 123.201.143.71. ENT-ATMARPENT:T...

Page 169 - ENT-IPPORT Command Parameters

8. IP Access Commands 4200-A2-GB20-00 August 2002 8-11 ENT-IPPORT The command ENT-IPPORT configures an Internet Protocol por t (or interface) in the NE. Table 8-9. ENT-IPPORT Command Parameters ENT-IPPORT:[tid]:aid_ipport:[ctag]::cfg_mode:ipport_nblk; RESTRICTIONS: All parameters in this command are...

Page 174 - Repor t IP por t facility parameters for ETH-1.

8. IP Access Commands 8-16 August 2002 4200-A2-GB20-00 Example Repor t IP por t facility parameters for ETH-1. REPT-OPSTAT-IPPORT:TAMPA:ETH-1 TAMPA 01-11-24 12:30:43M 42 COMPLD /* REPT-OPSTAT-IPPORT:TAMPA:ETH-1:42 */ "ETH-1:CURRATE,100000000" "ETH-1:CURDX,4DX" ; Related Commands None

Page 179 - Retrieve the configuration data associated with the ATM-1 port.

8. IP Access Commands 4200-A2-GB20-00 August 2002 8-21 Example Retrieve the configuration data associated with the ATM-1 port. RTRV-IPPORT:TAMPA:ATM-1:42; TAMPA 01-11-24 12:30:43M 42 COMPLD /* ; Related Commands DLT-ATMARPENT on page 8-2 ENT-IPPORT on page 8-11 ipport_nblk (continued) GATEWAY: IP ad...

Page 181 - This chapter contains the following Performance commands:

4200-A2-GB20-00 August 2002 9-1 9 Performance Commands Overview This chapter contains the following Performance commands: REPT-OPSTAT-ADSLCOM on page 9-2 REPT-OPSTAT-ADSLDN on page 9-5 REPT-OPSTAT-ADSLUP on page 9-7 REPT-OPSTAT-VCL on page 9-10

Page 184 - Examples

9. Performance Commands 9-4 August 2002 4200-A2-GB20-00 Examples Repor t ADSL DMT carrier operations parameters for ADSL-1-1-1-3. REPT-OPSTAT-ADSLCOM:TAMPA:ADSL-1-1-1-3:42; TAMPA 01-10-24 12:30:43M 42 COMPLD /* REPT-OPSTAT-ADSLCOM:TAMPA:ADSL-1-1-1-3:42 */ "ADSL-1-1-1-3:STATUSNE,NORMAL" "...

Page 193 - Fault Commands; This chapter contains the following Fault commands:

4200-A2-GB20-00 August 2002 10-1 10 Fault Commands Overview This chapter contains the following Fault commands: RTRV-ALM-ADSL on page 10-2 RTRV-ALM-ALL on page 10-5 RTRV-ALM-EQPT on page 10-9 RTRV-ALM-T1 on page 10-12 RTRV-ATTR-ADSL on page 10-15 RTRV-ATTR-ALL on page 10-18 RTRV-ATTR-E...

Page 197 - The RTRV-ALM-ALL command retrieves current alarms in the NE.

10. Fault Commands 4200-A2-GB20-00 August 2002 10-5 RTRV-ALM-ALL The RTRV-ALM-ALL command retrieves current alarms in the NE. Table 10-3. RTRV-ALM-ALL Command Parameters RTRV-ALM-ALL:[tid]:aid_all:[ctag]::[ntfcde],,[srveff],[locn],[dirn]; RESTRICTIONS: All parameters in this command are position-def...

Page 209 - Retrieve major attributes for all ADSL facilities.

10. Fault Commands 4200-A2-GB20-00 August 2002 10-17 Example Retrieve major attributes for all ADSL facilities. RTRV-ATTR-ADSL:TAMPA:ADSL:42::MJ; TAMPA 02-04-20 10:30:23M 42 COMPLD /* RTRV-ATTR-ADSL:TAMPA:ADSL:42::MJ */ "ADSL,ADSL:MJ,LOS,NEND,RCV"; Related Commands None Table 10-10. RTRV-ATT...

Page 216 - Retrieve service-affecting critical alarms for equipment.

10. Fault Commands 10-24 August 2002 4200-A2-GB20-00 Example Retrieve service-affecting critical alarms for equipment. RTRV-ATTR-EQPT:TAMPA:EQPT:42::MJ; TAMPA 02-04-20 10:30:23M 42 COMPLD /* RTRV-ATTR-EQPT:TAMPA:EQPT:42::MJ, */ "EQPT,EQPT:MJ,HITEMP,NEND,RCV"; Related Commands None

Page 219 - Retrieve critical attributes for T1 conditions.

10. Fault Commands 4200-A2-GB20-00 August 2002 10-27 Example Retrieve critical attributes for T1 conditions. RTRV-ATTR-T1:TAMPA:T1:42::CR; TAMPA 02-04-20 10:30:23M 42 COMPLD /* RTRV-ATTR-T1:TAMPA:T1:42::CR */ "T1,T1:CR,LOF,NEND,RCV"; Related Commands None [locn] Location of the condition. Va...

Page 229 - Retrieve current condition of LT alarm indicators.

10. Fault Commands 4200-A2-GB20-00 August 2002 10-37 Example Retrieve current condition of LT alarm indicators. RTRV-COND-EQPT:TAMPA:LT:42::; TAMPA 02-04-20 10:30:23M 42 COMPLD /* RTRV-COND-EQPT:TAMPA:LT:42:: */ "LT:MJ,HITEMP,SA,,,,,,Module temperature exceeded limit"; Related Commands None ...

Page 232 - Retrieve current conditions for NTT1 facility.

10. Fault Commands 10-40 August 2002 4200-A2-GB20-00 Example Retrieve current conditions for NTT1 facility. RTRV-COND-T1:TAMPA:NTT1:42::,; TAMPA 02-04-20 10:30:23M 42 COMPLD /* RTRV-COND-T1:TAMPA:NTT1:42::, */ "NTT1-1,T1:CR,LOS,SA,,,NEND,,,Loss of Signal/Clock"; Related Commands None ntfncde...

Page 233 - Log Commands; This chapter contains the following Log commands:

4200-A2-GB20-00 August 2002 11-1 11 Log Commands Overview This chapter contains the following Log commands: INIT-LOG on page 11-2 RTRV-LOG on page 11-4

Page 234 - The INIT-LOG command initializes selected logs.; INIT-LOG Command Parameters

11. Log Commands 11-2 August 2002 4200-A2-GB20-00 INIT-LOG The INIT-LOG command initializes selected logs. Response Format If, in less than 2 seconds, a normal or error response cannot be sent, the following acknowledgment response will be sent: IP c After the above response, a new command input may...

Page 235 - Initialize the SYSTEM log.; Related Command; INIT-LOG Response Parameters

11. Log Commands 4200-A2-GB20-00 August 2002 11-3 Example Initialize the SYSTEM log. INIT-LOG:TAMPA::40::SYSTEM; TAMPA 02-07-24 10:30:43M 40 COMPLD /* INIT-LOG:TAMPA::40::SYSTEM */; Related Command RTRV-LOG on page 11-4 Table 11-2. INIT-LOG Response Parameters Parameter Explanation sid Source NE ide...

Page 236 - The RTRV-LOG command retrieves selected logs.; RTRV-LOG Command Parameters

11. Log Commands 11-4 August 2002 4200-A2-GB20-00 RTRV-LOG The RTRV-LOG command retrieves selected logs. Response Format If, in less than 2 seconds, a normal or error response cannot be sent, the following acknowledgment response will be sent: IP c After the above response, a new command input may b...

Page 237 - Retrieve the SECURITY log.; RTRV-LOG Response Parameters

11. Log Commands 4200-A2-GB20-00 August 2002 11-5 Example Retrieve the SECURITY log. RTRV-LOG:TAMPA::40::SECURITY; TAMPA 02-07-24 10:30:43M 40 COMPLD /* RTRV-LOG:TAMPA::40::SECURITY */ (dump of log buffer) ; Related Command INIT-LOG on page 11-2 Table 11-4. RTRV-LOG Response Parameters Parameter Exp...

Page 239 - Security Commands; This chapter contains the following Security commands:

4200-A2-GB20-00 August 2002 12-1 12 Security Commands Overview This chapter contains the following Security commands: DLT-USER-SECU on page 12-2 ED-CID-SECU on page 12-4 ED-PID on page 12-6 ED-USER-SECU on page 12-8 ENT-USER-SECU on page 12-10 RTRV-CID-SECU on page 12-12 RTRV-USER-SECU...

Page 241 - Delete user RICHARD.

12. Security Commands 4200-A2-GB20-00 August 2002 12-3 Example Delete user RICHARD. DLT-USER-SECU:TAMPA:RICHARD:42; TAMPA 01-11-24 12:30:43M 42 COMPLD /* DLT-USER-SECU:TAMPA:RICHARD:42 */; Related Commands ED-USER-SECU on page 12-8 ENT-USER-SECU on page 12-10 RTRV-USER-SECU on page 12-14 Table 12-2....

Page 244 - ED-PID Command Parameters

12. Security Commands 12-6 August 2002 4200-A2-GB20-00 ED-PID The ED-PID command edits a user’s own Private Identifier (password). Response Format If, in less than 2 seconds, a normal or error response cannot be sent, the following acknowledgment response is sent: IP c After the above response, a ne...

Page 245 - ED-PID Response Parameters

12. Security Commands 4200-A2-GB20-00 August 2002 12-7 Example Change Richard’s password from RCC-1210D to NR-12345. ED-PID:TAMPA:RICHARD:42::RCC-1210D,NR-12345; TAMPA 01-11-24 12:30:43M 42 COMPLD /* ED-PID:TAMPA:RICHARD:42::RCC-1210D,NR-12345 */; Related Command None Table 12-6. ED-PID Response Par...

Page 251 - Retrieve the configuration data for the local console interface.

12. Security Commands 4200-A2-GB20-00 August 2002 12-13 Example Retrieve the configuration data for the local console interface. RTRV-CID-SECU:TAMPA:CRAFT:42; TAMPA 01-11-24 12:30:43M 42 COMPLD /* RTRV-CID-SECU:TAMPA:CRAFT:42 */; "CRAFT:SUPER,MXINV=3, TMOUT=10" Related Command ED-CID-SECU on...

Page 253 - Retrieve the security levels for user RICHARD.

12. Security Commands 4200-A2-GB20-00 August 2002 12-15 Example Retrieve the security levels for user RICHARD. RTRV-USER-SECU:TAMPA:RICHARD:42; TAMPA 01-11-24 12:30:43M 42 COMPLD /* RTRV-USER-SECU:TAMPA:RICHARD:42 */ "RICHARD:RTRV:PAGE=0,UAGE=0"; Related Commands DLT-USER-SECU on page 12-2 E...

Page 255 - Synchronization Commands; This chapter contains the following Synchronization commands:

4200-A2-GB20-00 August 2002 13-1 13 Synchronization Commands Overview This chapter contains the following Synchronization commands: ED-SYNCN on page 13-2 RD-SYNCN on page 13-4 RTRV-SYNCN on page 13-6

Page 256 - ED-SYNCN Command Parameters

13. Synchronization Commands 13-2 August 2002 4200-A2-GB20-00 ED-SYNCN The ED-SYNCN Command configures the reference source for synchronization of the NE clock. Response Format If, in less than 2 seconds, a normal or error response cannot be sent, the following acknowledgment response is sent: IP c ...

Page 257 - ED-SYNCN Response Parameters

13. Synchronization Commands 4200-A2-GB20-00 August 2002 13-3 Example Configure the NE clock to use the local oscillator as its primar y reference source. ED-SYNCN:TAMPA:CLKSRCNT:42:::PRICREF=LOCAL; TAMPA 01-12-20 11:20:34M 42 COMPLD /* ED-SYNCN:TAMPA:CLKSRCNT:42:::PRICREF=LOCAL*/; Related Commands ...

Page 258 - RD-SYNCN Command Parameters

13. Synchronization Commands 13-4 August 2002 4200-A2-GB20-00 RD-SYNCN The RD-SYNCN Command retrieves the current reference source for synchronization of the NE clock. Response Format If, in less than 2 seconds, a normal or error response cannot be sent, the following acknowledgment response is sent...

Page 259 - Retrieve the NE clock source.; RD-SYNCN Response Parameters

13. Synchronization Commands 4200-A2-GB20-00 August 2002 13-5 Example Retrieve the NE clock source. RD-SYNCN:TAMPA:CLKSRCNT:42; TAMPA 01-12-20 11:20:34M 42 COMPLD /* RD-SYNCN:TAMPA:CLKSRCNT:42*/; Related Commands None Table 13-4. RD-SYNCN Response Parameters Parameter Explanation tid Target NE ident...

Page 260 - RTRV-SYNCN Command Parameters

13. Synchronization Commands 13-6 August 2002 4200-A2-GB20-00 RTRV-SYNCN The RTRV-SYNCN Command retrieves the configuration of the reference source for synchronization of the NE clock. Response Format If, in less than 2 seconds, a normal or error response cannot be sent, the following acknowledgment...

Page 261 - RTRV-SYNCN Response Parameters

13. Synchronization Commands 4200-A2-GB20-00 August 2002 13-7 Example Retrieve the configuration of the reference source for synchronization of the NE clock. RTRV-SYNCN:TAMPA:CLKSRCNT:42; TAMPA 01-12-20 11:20:34M 42 COMPLD /* RTRV-SYNCN:TAMPA:CLKSRCNT:42 */ CLKSRCNT::PRICREF=LOCAL; Related Commands ...

Page 263 - This chapter contains the following System commands:; LOGOFF

4200-A2-GB20-00 August 2002 14-1 14 System Commands Overview This chapter contains the following System commands: ACT-USER on page 14-2 ALW-MSG-ALL on page 14-4 CANC-USER on page 14-6 CPY-FILE on page 14-8 INH-MSG-ALL on page 14-9 INIT-SYS on page 14-11 LOGOFF on page 14-13 RTRV-HDR ...

Page 264 - The ACT-USER command logs a user on and begins a user session.; ACT-USER Command Parameters

14. System Commands 14-2 August 2002 4200-A2-GB20-00 ACT-USER The ACT-USER command logs a user on and begins a user session. Response Format If, in less than 2 seconds, a normal or error response cannot be sent, the following acknowledgment response will be sent: IP c After the above response, a new...

Page 265 - ACT-USER Response Parameters

14. System Commands 4200-A2-GB20-00 August 2002 14-3 Example Activate JANET, whose password is ABC-1234. ACT-USER:TAMPA:JANET:1::ABC-1234; TAMPA 01-10-25 10:35:34M 40 COMPLD /* ACT-USER:JANET:1::40 ****** */; Related Command CANC-USER on page 14-6 Table 14-2. ACT-USER Response Parameters Parameter E...

Page 267 - Enable the autonomous messages to be repor ted in the OS.

14. System Commands 4200-A2-GB20-00 August 2002 14-5 Example Enable the autonomous messages to be repor ted in the OS. ALW-MSG-ALL:TAMPA:ALL:40::MN; TAMPA 01-10-24 12:30:43M 40 COMPLD /* ALW-MSG-ALL:TAMPA:ALL:40::MN */; Related Command INH-MSG-ALL on page 14-9 Table 14-4. ALW-MSG-ALL Response Parame...

Page 268 - The CANC-USER command logs off a user’s own session.; CANC-USER Command Parameters

14. System Commands 14-6 August 2002 4200-A2-GB20-00 CANC-USER The CANC-USER command logs off a user’s own session. Response Format If, in less than 2 seconds, a normal or error response cannot be sent, the following acknowledgment response will be sent: IP c After the above response, a new command ...

Page 269 - Cancel the user ID JANET.; CANC-USER Response Parameters

14. System Commands 4200-A2-GB20-00 August 2002 14-7 Example Cancel the user ID JANET. CANC-USER:TAMPA:JANET:40; TAMPA 01-10-25 10:35:34M 40 COMPLD /* CANC-USER:TAMPA:JANET:40 */; Related Command ACT-USER on page 14-2 DLT-USER-SECU on page 12-2 ED-USER-SECU on page 12-8 ENT-USER-SECU on page 12-10 R...

Page 270 - CPY-FILE Command Parameters

14. System Commands 14-8 August 2002 4200-A2-GB20-00 CPY-FILE The CPY-FILE command copies the contents of a configuration or software file on a selected equipment module to or from an external file server. Table 14-7. CPY-FILE Command Parameters CPY-FILE:[tid]:aid_eqpt:[ctag]::svripaddr[,srcfile] [,...

Page 274 - Perform a complete reset of the NTA unit.

14. System Commands 14-12 August 2002 4200-A2-GB20-00 Example Perform a complete reset of the NTA unit. INIT-SYS:TAMPA:NTA:40::3; TAMPA 02-03-22 10:30:23M 40 COMPLD /* INIT-SYS:TAMPA:NTA:40::3 */; Related Commands None Table 14-11. INIT-SYS Response Parameters Parameter Explanation sid Source NE ide...

Page 275 - The LOGOFF command logs the invoking terminal session.

14. System Commands 4200-A2-GB20-00 August 2002 14-13 LOGOFF The LOGOFF command logs the invoking terminal session. Response Format If, in less than 2 seconds, a normal or error response cannot be sent, the following acknowledgment response will be sent: IP c After the above response, a new command ...

Page 276 - Log off the TAMPA NE.

14. System Commands 14-14 August 2002 4200-A2-GB20-00 Example Log off the TAMPA NE. LOGOFF:TAMPA::40; TAMPA 01-10-25 10:35:34M 40 COMPLD /* LOGOFF:TAMPA::40 */; Related Command ACT-USER on page 14-2 Table 14-13. LOGOFF Response Parameters Parameter Explanation sid Source NE identification yy-mm-dd Y...

Page 277 - The RTRV-HDR command retrieves the NE header information.

14. System Commands 4200-A2-GB20-00 August 2002 14-15 RTRV-HDR The RTRV-HDR command retrieves the NE header information. Response Format If, in less than 2 seconds, a normal or error response cannot be sent, the following acknowledgment response will be sent: IP c After the above response, a new com...

Page 278 - Retrieve header information for the TAMPA NE.

14. System Commands 14-16 August 2002 4200-A2-GB20-00 Example Retrieve header information for the TAMPA NE. RTRV-HDR:TAMPA::42; TAMPA 01-10-24 11:30:13M 42 COMPLD /* RTRV-HDR:TAMPA::42 */; Related Commands None Table 14-15. RTRV-HDR Response Parameters Parameter Explanation tid Target NE identificat...

Page 280 - Retrieve the list of software image files for the TAMPA NE.

14. System Commands 14-18 August 2002 4200-A2-GB20-00 Example Retrieve the list of software image files for the TAMPA NE. RTRV-MEM:TAMPA:COM:40; TAMPA 02-07-24 12:30:43M 40 COMPLD /* RTRV-MEM:TAMPA:COM:40 */ (filename) ; Related Commands None Table 14-17. RTRV-MEM Response Parameters Parameter Expla...

Page 282 - Retrieve the AID for the RTRV-IPPORT command.

14. System Commands 14-20 August 2002 4200-A2-GB20-00 Example Retrieve the AID for the RTRV-IPPORT command. RTRV-META-AID:TAMPA:IPPORT:40; TAMPA 02-07-24 12:30:43M 40 COMPLD IPPORT:ATM-{1,2} IPPORT:ETH-{1}, ; Related Commands None

Page 286 - Retrieve the syntax for the RTRV-IPPORT command.

14. System Commands 14-24 August 2002 4200-A2-GB20-00 Example Retrieve the syntax for the RTRV-IPPORT command. RTRV-META-SYN:TAMPA:RTRV-IPPORT:40; TAMPA 02-07-24 12:30:43M 40 COMPLD "RTRV-IPPORT:RTRV-IPPORT:[tid]:aid_ipport;[ctag}::[skipped]: [skipped]:[pstf]"; Related Commands None

Page 291 - The SET-DAT command sets the date and time in an NE.

14. System Commands 4200-A2-GB20-00 August 2002 14-29 SET-DAT The SET-DAT command sets the date and time in an NE. Response Format If, in less than 2 seconds, a normal or error response cannot be sent, the following acknowledgment response will be sent: IP c After the above response, a new command i...

Page 299 - Test Commands; This chapter contains the following Test commands:

4200-A2-GB20-00 August 2002 15-1 15 Test Commands Overview This chapter contains the following Test commands: OPR-LPBK-T1 on page 15-2 OPR-LPBK-VCL on page 15-4 RLS-LPBK-T1 on page 15-7 RLS-LPBK-VCL on page 15-9 STA-LAMPTST on page 15-11 STP-LAMPTST on page 15-13

Page 301 - Place NTT1 circuit 1 in payload loopback mode.

15. Test Commands 4200-A2-GB20-00 August 2002 15-3 Error Response: sid yy-mm-dd hh:mm:ssM c DENY /* OPR-LPBK-T1:[tid]:aid_ds1:[ctag]::,,,[lpbktype] */ aid:ERRCDE=errcde /* error description */; Example Place NTT1 circuit 1 in payload loopback mode. OPR-LPBK-T1:TAMPA:NTT1-1:40::,,,PAYLOAD; TAMPA 01-1...

Page 306 - Release the NTT1 circuit 1 from payload loopback mode.

15. Test Commands 15-8 August 2002 4200-A2-GB20-00 Example Release the NTT1 circuit 1 from payload loopback mode. RLS-LPBK-T1:TAMPA:NTT1-1:40; TAMPA 01-11-24 12:30:43M 40 COMPLD /* RLS-LPBK-T1:TAMPA:NTT1-1:40 */; Related Command OPR-LPBK-T1 on page 15-2 Table 15-6. RLS-LPBK-T1 Response Parameters Pa...

Page 309 - STA-LAMPTST Command Parameters

15. Test Commands 4200-A2-GB20-00 August 2002 15-11 STA-LAMPTST The STA-LAMPTST command starts a lamp (LED) test on the NE. Response Format If, in less than 2 seconds, a normal or error response cannot be sent, the following acknowledgment response is sent: IP c After the above response, a new comma...

Page 310 - Star t a lamp test on the TAMPA device.

15. Test Commands 15-12 August 2002 4200-A2-GB20-00 Example Star t a lamp test on the TAMPA device. STA-LAMPTST:TAMPA:COM; TAMPA 01-11-24 12:30:43M 40 COMPLD /* STA-LAMPTST:TAMPA:COM */; Related Command STP-LAMPTST on page 15-13 Table 15-10. STA-LAMPTST Response Parameters Parameter Explanation sid ...

Page 312 - Stop a lamp test on the TAMPA device.

15. Test Commands 15-14 August 2002 4200-A2-GB20-00 Example Stop a lamp test on the TAMPA device. STP-LAMPTST:TAMPA:COM; TAMPA 01-11-24 12:30:43M 40 COMPLD /* STP-LAMPTST:TAMPA:COM */; Related Command STA-LAMPTST on page 15-11 Table 15-12. STP-LAMPTST Response Parameters Parameter Explanation sid So...

Page 313 - Error Code

4200-A2-GB20-00 August 2002 A-1 A Error Codes Overview An error code is 4-character code that can appear in the response of an input command describing why the command cannot be executed. Error codes are grouped into the following types: Equipment (E) Input (I) Multiple errors (M) Privilege ...

Page 315 - Command Cross Reference

4200-A2-GB20-00 August 2002 B-1 B Command Cross Reference Overview This appendix lists all commands in alphabetical order for easy reference. ACT Commands on page B-2 ALW Commands on page B-2 CANC Commands on page B-2 CPY Commands on page B-2 DLT Commands on page B-3 ED Commands on page ...

Page 316 - ACT Commands; Activate (ACT) commands activate a network element or a user.; ALW Commands

B. Command Cross Reference B-2 August 2002 4200-A2-GB20-00 ACT Commands Activate (ACT) commands activate a network element or a user. ALW Commands Allow (ALW) commands enable automatic operation. CANC Commands Cancel (CANC) commands cancel/terminate. CPY Commands Copy (CPY) commands copy. Table B-1....

Page 317 - DLT Commands

B. Command Cross Reference 4200-A2-GB20-00 August 2002 B-3 DLT Commands Delete (DLT) commands remove or unassign. ED Commands Edit (ED) commands change configuration data. Table B-5. DLT Commands Command See . . . DLT-ATMARPENT DLT-ATMARPENT on page 8-2 in Chapter 8, IP Access Commands DLT-CRS-VC DL...

Page 318 - ENT Commands; Command

B. Command Cross Reference B-4 August 2002 4200-A2-GB20-00 ENT Commands Enter (ENT) commands add new data records. ED-PROFILE-ADSLDNALM ED-PROFILE-ADSLDNALM on page 3-16 in Chapter 3, ADSL Facility Commands ED-PROFILE-ADSLUP ED-PROFILE-ADSLUP on page 3-19 in Chapter 3, ADSL Facility Commands ED-PROF...

Page 319 - INH Commands; The logoff command logs off the invoking terminal session.; OPR Commands

B. Command Cross Reference 4200-A2-GB20-00 August 2002 B-5 INH Commands Inhibit (INH) commands disable an automatic operation. INIT Commands Initialize (INIT) commands initialize an entry or system. LOGOFF Commands The logoff command logs off the invoking terminal session. OPR Commands Operate (OPR)...

Page 320 - RD Commands; Repor t (REPT) commands report current operational parameters.

B. Command Cross Reference B-6 August 2002 4200-A2-GB20-00 RD Commands Read (RD) commands retrieve data from the NE. REPT Commands Repor t (REPT) commands report current operational parameters. Table B-12. RD Commands Command See . . . RD-SYNCN RD-SYNCN on page 13-4 in Chapter 13, Synchronization Co...

Page 321 - RTRV Commands

B. Command Cross Reference 4200-A2-GB20-00 August 2002 B-7 RTRV Commands Retrieve (RTRV) commands retrieve data from the NE. Table B-14. RTRV Commands (1 of 3) Command See . . . RTRV-ADSL RTRV-ADSL on page 3-32 in Chapter 3, ADSL Facility Commands RTRV-ALM-ALL RTRV-ALM-ALL on page 10-5 in Chapter 10...

Page 323 - SET Commands

B. Command Cross Reference 4200-A2-GB20-00 August 2002 B-9 SET Commands Set (SET) commands modify data related to the system. STA Commands Star t (STA) commands star t a test. STP Commands Stop (STP) commands stop a test. RTRV-USER-SECU RTRV-USER-SECU on page 12-14 in Chapter 12, Security Commands R...

Page 325 - Traps and MIBs; SNMP Overview; Technical Suppor t

4200-A2-GB20-00 August 2002 C-1 C Traps and MIBs SNMP Overview The Simple Network Management Protocol (SNMP) is an application-level protocol used in network management to gather information from network devices. Each GranDSLAM 4200 runs an SNMP agent that collects data. The network management stati...

Page 326 - SNMP Traps; , lists the traps supported by the GranDSLAM 4200.; Description

C. Traps and MIBs C-2 August 2002 4200-A2-GB20-00 SNMP Traps Table C-1, SNMP Traps , lists the traps supported by the GranDSLAM 4200. Table C-1. SNMP Traps (1 of 3) Trap Event (Trap #) Description Variable Binding Standard Traps authenticationFailure (5) The authenticationFailure trap signifies that...

Page 329 - MIBs Overview; Technical Support; Standard MIBs

C. Traps and MIBs 4200-A2-GB20-00 August 2002 C-5 MIBs Overview The GranDSLAM 4200 DSL system suppor ts standard as well as Paradyne Enter prise MIBs. Various configuration, status, and statistical data within the SNMP agent is accessible from the NMS. The content of an SNMP agent’s MIBs is defined ...

Page 330 - ATM Forum MIB; — Physical Group

C. Traps and MIBs C-6 August 2002 4200-A2-GB20-00 ATM Forum MIB — SNMP M4 Network Element View MIB (atmfM4.mib) and atmfM4Ext.mib Entity MIB (version 2) (RFC 2737) — Physical Group — Mapping Group — General Group — Notifications Group DMT Line Code Specific MIB (RFC 2662) — Includes ADSL suppl...

Page 332 - Interfaces Group (see; Evolution of the Interfaces Group of MIB II (RFC 2863); Object

C. Traps and MIBs C-8 August 2002 4200-A2-GB20-00 MIB II (RFC 2863) The objects defined by MIB II (RFC 2863) are organized into the following groups: Interfaces Group (see Evolution of the Interfaces Group of MIB II (RFC 2863) ) MIB II (RFC 2863) Extension to the Interface Table MIB II (RFC 28...

Page 336 - MIB II (RFC 2863) Extension to the Interface Table; Read/Write. SNMP traps must be enabled on; ifIndex Assignments; GranDSLAM 4200 IfStackTable Entries

C. Traps and MIBs C-12 August 2002 4200-A2-GB20-00 MIB II (RFC 2863) Extension to the Interface Table This extension contains additional objects for the Interface table. Only the following objects are suppor ted: ifLinkUpDownTrapEnable(14) − Read/Write. SNMP traps must be enabled on the unit for c...

Page 338 - ATM Interface Configuration Parameter Group (RFC 2515); Table C-6, ATM Interface Configuration MIB Group Objects; ATM Interface Configuration MIB Group Objects (1 of 2)

C. Traps and MIBs C-14 August 2002 4200-A2-GB20-00 ATM Interface Configuration Parameter Group (RFC 2515) This group contains information on ATM cell layer configuration of local ATM interfaces (Backplane and Management Processor) on an ATM device (see Table C-6, ATM Interface Configuration MIB Grou...

Page 339 - ATM Interface Traffic Descriptor Group (RFC 2515); ATM Interface Configuration MIB Group Objects (2 of 2)

C. Traps and MIBs 4200-A2-GB20-00 August 2002 C-15 ATM Interface Traffic Descriptor Group (RFC 2515) The ATM virtual link tables use this ATM Traffic Descriptor table to assign traffic parameters and service category to the receive and trnsmit directions of the ATM virtual links (VPLs and VCLs). The...

Page 340 - MIB Group Objects; VCL Configuration MIB Group Objects

C. Traps and MIBs C-16 August 2002 4200-A2-GB20-00 ATM VCL Configuration Group (RFC 2515) Contains configuration and state information of a bidirectional VCL at an ATM interface. The atmVclEntry is supported as shown in Table C-7, VCL Configuration MIB Group Objects . Table C-7. VCL Configuration MI...

Page 341 - Virtual Channel Cross Connect Group (RFC 2515); Channel Cross Connect Group Objects; Virtual Channel Cross Connect Group Objects

C. Traps and MIBs 4200-A2-GB20-00 August 2002 C-17 Virtual Channel Cross Connect Group (RFC 2515) This table contains configuration and state information of point-to-point, point-to-multipoint, and multipoint-to-multipoint VC cross-connections for PVCs. This table has read access and is used to cros...

Page 342 - Table C-9, ATM Forum SNMP M4 Network Element View MIB Group Objects; ATM Forum SNMP M4 Network Element View MIB Group Objects

C. Traps and MIBs C-18 August 2002 4200-A2-GB20-00 ATM Forum MIB The ATM Forum MIB (atmfM4.MIB) is defined in the ATM Forum SNMP M4 Network Element View MIB document. The suppor ted objects are listed in Table C-9, ATM Forum SNMP M4 Network Element View MIB Group Objects . Table C-9. ATM Forum SNMP ...

Page 343 - Table

C. Traps and MIBs 4200-A2-GB20-00 August 2002 C-19 Paradyne Extensions to the ATM Interface Configuration Table, ATM Forum M4 The following MIBs listed in Table C-10, Paradyne Extensions to ATM Interface Configuration Table , are intended to augment the ATM Interface Configuration Table, ATM Forum M...

Page 344 - Table C-11, Entity Physical Group Objects

C. Traps and MIBs C-20 August 2002 4200-A2-GB20-00 Entity MIB (version 2) (RFC 2737) The Entity MIB contains the following five groups of MIB objects: entityPhysical Group − Describes the physical entities managed by a single agent. Supported. See Entity Physical Group (RFC 2737) . entityLogical...

Page 351 - Table C-12, DMT Line Code Specific MIB Objects

C. Traps and MIBs 4200-A2-GB20-00 August 2002 C-27 DMT Line Code Specific MIB (RFC 2662) The objects suppor ted for the DMT Line Code Specific MIB are listed in Table C-12, DMT Line Code Specific MIB Objects . Table C-12. DMT Line Code Specific MIB Objects (1 of 5) Table Objects Contents adslLineEnt...

Page 356 - ADSL Supplement to the ADSL Line MIB; Table C-13, ADSL Supplement to the ADSL Line MIB Objects; Table C-13. ADSL Supplement to the ADSL Line MIB Objects

C. Traps and MIBs C-32 August 2002 4200-A2-GB20-00 ADSL Supplement to the ADSL Line MIB The objects suppor ted for the supplement to the ADSL Line MIB are listed in Table C-13, ADSL Supplement to the ADSL Line MIB Objects . Table C-13. ADSL Supplement to the ADSL Line MIB Objects Table Objects Conte...

Page 357 - The objects supported for the DS1 MIB are listed in

C. Traps and MIBs 4200-A2-GB20-00 August 2002 C-33 DS1 MIB (RFC 2495) The objects supported for the DS1 MIB are listed in Table C-14, DS1 MIB Objects . Table C-14. DS1 MIB Objects (1 of 3) Table Objects Contents dsx1ConfigEntry dsx1LineIndex dsx1IfIndex dsx1TimeElapsed dsx1ValidIntervals d...

Page 360 - Paradyne Enterprise MIBs; The following Paradyne Enterprise MIB Objects are suppor ted:; Paradyne DS1 Extension MIB; System MIB Objects

C. Traps and MIBs C-36 August 2002 4200-A2-GB20-00 Paradyne Enterprise MIBs The following Paradyne Enterprise MIB Objects are suppor ted: Paradyne DSLAM System MIB (pdn_dslam.mib) Paradyne Security MIB (pdn_Security.mib) Paradyne Syslog MIB (pdn_syslog.mib) Paradyne Health and Status MIB (mp...

Page 362 - Security MIB Objects

C. Traps and MIBs C-38 August 2002 4200-A2-GB20-00 Paradyne Security MIB (pdn_Security.mib) The Paradyne Security MIB (pdn_Security.mib) enables an SNMP manager to control the security aspects of the unit. The objects listed in Table C-16, Paradyne Security MIB Objects , are supported. sysDevConfigU...

Page 365 - and Status MIB Objects

C. Traps and MIBs 4200-A2-GB20-00 August 2002 C-41 Paradyne Health and Status MIB (mpe_HealthAndStatus.mib) The Paradyne Health and Status MIB (mpe_HealthAndStatus.mib) stores the results of the Power-On Self Test. This MIB begins with mpe, indicating that it is indexed on the entPhysicalIndex and d...

Page 366 - Control MIB Objects

C. Traps and MIBs C-42 August 2002 4200-A2-GB20-00 Paradyne Control MIB (pdn_Control.mib) The Paradyne Control MIB (pdn_Control.mib) stores the results of the Power-On Self Test. This MIB begins with pdn, indicating that it can be used if the Entity MIB is not implemented. The objects supported are ...

Page 370 - Table C-27, Paradyne Extension to DS1 Config MIB Objects

C. Traps and MIBs C-46 August 2002 4200-A2-GB20-00 Paradyne DS1 Config MIB (RFC 2495) The objects suppor ted for the DS1 MIB are listed in Table C-26, DS1 Config MIB Objects . Paradyne DS1 Extension MIB The objects suppor ted for the Paradyne extension to the DS1 MIB are listed in Table C-27, Parady...

Page 371 - Hotwire 6390 ReachDSL Modem Overview; The ReachDSL technology:; Hotwire ReachDSL Modem, Model 6390 with Inline Phone Filter,; , for instructions on how to install the Hotwire 6390

4200-A2-GB20-00 August 2002 D-1 D Hotwire 6390 ReachDSL Modem Download Hotwire 6390 ReachDSL Modem Overview The Hotwire 6390 ReachDSL Modem is a component in the ReachDSL System and interoperates with the GranDSLAM 4200 ATM Stackable DSLAM. This system provides high-speed Internet or cor porate LAN ...

Page 372 - Downloading Hotwire 6390 ReachDSL Modem Software; 390 ReachDSL Modem Software Download; Network View of Hotwire 6390 ReachDSL Modem Software Download

D. Hotwire 6390 ReachDSL Modem Download D-2 August 2002 4200-A2-GB20-00 Downloading Hotwire 6390 ReachDSL Modem Software The Hotwire 6390 ReachDSL Modem is capable of receiving a download of its software while continuing to pass data. Before attempting to download, you must first build a management ...

Page 373 - Log into the GranDSLAM 4200 unit using the

D. Hotwire 6390 ReachDSL Modem Download 4200-A2-GB20-00 August 2002 D-3 Procedure To create a PVC from the GrandDSLAM 4200 port to the Hotwire 6390 ReachDSL modem: 1. Log into the GranDSLAM 4200 unit using the ACT-USER command. For example, type: ACT-USER:TAMPA:SUPERUSER:100::******** 2. Create a VC...

Page 374 - password

D. Hotwire 6390 ReachDSL Modem Download D-4 August 2002 4200-A2-GB20-00 Procedure To download new software to the Hotwire 6390 ReachDSL Modem flash memory: 1. Create the following files on a PC using Notepad or a text editor program and place them in the same folder as the batch file you will create...

Page 375 - Index

4200-A2-GB20-00 August 2002 IN-1 Index A ACT PROFILE-ADSL, 3-2PROFILE-ADSLALM, 3-4USER, 14-2 ACT commands, B-2activate ADSL alarm profile, 3-4ADSL profile, 3-2user, 14-2 ACT-PROFILE ADSL, 3-2ADSLALM, 3-4 ADSL activate alarm profile, 3-4activate profile, 3-2delete alarm profile, 3-8delete profile, 3-...