ParaBody 889 - Manuals - manualsarea.com

Page 2 - IMPORTANT SAFETY INFORMATION; TABLE OF CONTENTS

THERE IS A RISK ASSUMED BY INDIVIDUALS WHO USE THIS TYPE OF EQUIPMENT. TO MINIMIZE RISK FOLLOW THESE RULES ! 1. Before using, read all the warnings and instructionson the use of this machine. Use only for intendedexercise. DO NOT modify the machine. 2. Obtain a medical exam before beginning anyexerc...

Page 3 - BOLT LENGTH RULER:; Bolt Length Ruler; BOLT LENGTH

IMPORTANT NOTES Please note: Tools Required for Assembly * Thank you for purchasing the ParaBody 889 Weight Stack Option. Please read these instructions thoroughly and keep them for future reference. This product must be assembled on a flat, level surface to assure its proper function. * 3/4” wrench...

Page 4 - PARTS LIST; FIGURE 1

4 PARTS LIST PART # LEA6814309 LEA6800610 LEA6814009 LEA6813709 LEA6801110 LEA6816501 LEA6274410 LEA6725310 LEA3116201 LEA3116101 LEA6832801 LEA6671002 LEA6692601 LEA3103102 LEA3103302 LEA6405201 LEA6972201 LEA6177001 LEA3119301 LEA6236701 LEA6412001 KEY 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 ...

Page 5 - FIGURE 2; FIGURE 3

STEP 2: FIGURE 2 • Insert two 2” END CAP (16) into the ends of the STACK BASE (3) as shown in FIGURE 2. • Attach four 3/4 X 1-1/2” GLIDES (24) to the inside of the tube on the STACK BASE (3) as shown in FIGURE 2 using the following steps: • Thoroughly clean all surfaces where the 3/4 X 1-1/2” GLIDES...

Page 6 - FIGURE 4

6 FIGURE 4 STEP 4: • SECURELY assemble the STACK BASE (3) and the UPRIGHT (1) to the LOWER CROSS SUPPORT using two 3/8 X 4” BOLTS (38), four 3/8” WASHERS (30), and two 3/8” LOW HEIGHT LOCK NUTS (29). See FIGURE 4. 3/8 X 4” 38 29 1 LOWER CROSS SUPPORT 3 UPRIGHT FRAME 30 30 • NOTE: It may be necessary...

Page 7 - FIGURE 5

7 0 1 2 3 4 5 6 1/2 1/2 1/2 1/2 1/2 1/2 FIGURE 5 STEP 5: • Insert two GUIDE RODS (6) into the STACK BASE (3) as shown in FIGURE 5. Lubricatethe GUIDE RODS (6) with a silicon or teflonspray that is available at most hardware stores. • Slide two WEIGHT STACK CUSHIONS (26) down over the GUIDE RODS (6)....

Page 8 - FIGURE 6

8 STEP 6: FIGURE 6 • LOOSELY assemble the TOP BOOM (4) to the UPPER CROSS SUPPORT using two 3/8 X 4” BOLTS (38), four 3/8” WASHERS (30) and two 3/8” LOCK NUTS (31). See FIGURE 6. • Insert two 3 X 2” END CAPS (13) into the ends of the TOP BOOM (4). See FIGURE 6. • SECURELY tighten all connections mad...

Page 9 - FIGURE 8; FIGURE 7

9 0 1 2 3 4 5 6 1/2 1/2 1/2 1/2 1/2 1/2 STEP 8: FIGURE 8 • Route the 115-3/4” CABLE (12) through the TOP BOOM (4) as shown in FIGURE 8. (NOTE: It may be necessary to remove the 3/8 X 2-3/4” BOLT to ensure CABLE is routed over the TOP of the BOLT.) • SECURELY assemble three 3-1/2” PULLEYS (9) into th...

Page 10 - FIGURE 9

STEP 9: FIGURE 9 1 0 31 • Place one 3-1/2” PULLEY (9) into the loop of the CABLE (12) below the second and third PULLEY of the TOP BOOM (4) as shown in FIGURE 9. • LOOSELY assemble two 3/16 X 1-3/4 X 5-1/4” PLATES (23) to each side of the 3-1/2” PULLEY (9) using one 3/8 X 2” BOLT (35), two 3/8” WASH...

Page 14 - SERIAL NUMBER LOCATION

MAINTENANCE MODEL #________________________ SERIAL #_________________________ DATE OF PURCHASE: _____________ DEALERS NAME: _________________ DEALERS PHONE #_______________ 1 4 * We recommend cleaning your product (pads and frame) on a regular basis, using warm soapy water. Touch-up paint can be pur...

Page 15 - LIMITED WARRANTY

1 5 NOTES: LIMITED WARRANTY ParaBody extends the following LIMITED WARRANTY to the original owner of the ParaBody products. The Warranty terms apply to IN HOME USE ONLY. 1. LIMITED WARRANTY ON FRAME AND WELDS. If the frame of the ParaBody product or a weld should crack or break, it will be repaired ...