ParaBody 883 - Manuals - manualsarea.com

Page 2 - IMPORTANT SAFETY INFORMATION; TABLE OF CONTENTS

THERE IS A RISK ASSUMED BY INDIVIDUALS WHO USE THIS TYPE OF EQUIPMENT. TO MINIMIZE RISK FOLLOW THESE RULES ! 1. Before using, read all the warnings and instructionson the use of this machine. Use only for intendedexercise. DO NOT modify the machine. 2. Obtain a medical exam before beginning anyexerc...

Page 3 - BOLT LENGTH RULER:; Bolt Length Ruler; BOLT LENGTH

IMPORTANT NOTES Please note: Tools Required for Assembly * Thank you for purchasing the ParaBody 880 Second Stack Option. Please read these instructions thoroughly and keep them for future reference. 3 NOTE: BOLT LENGTH IS MEASURED FROM THE UNDERSIDE OF THE HEAD OF THE BOLT. BOLT LENGTH RULER: * Thi...

Page 4 - PARTS LIST; GYM SYSTEM without LEG PRESS OPTION, please refer to PAGE 5.

PART # 7 1 6 0 2 0 8 7 1 6 7 9 0 8 6 5 2 3 4 0 1 7 0 9 5 7 0 1 7 0 1 2 1 0 2 6 9 5 7 3 0 2 7 1 6 5 7 0 1 7 1 5 6 1 0 1 311 6 2 0 1 6 9 7 2 2 0 1 3 1 0 8 0 0 2 6 9 7 8 1 0 1 KEY 1 2 3 4 5 6 7 8 9 1 0 11 1 2 QTY 1 1 2 1 2 1 1 1 2 1 2 1 PART # 3 1 0 2 9 2 4 3 1 0 2 8 0 7 3 1 0 2 9 0 6 3 1 0 2 9 5 5 3 1...

Page 5 - FIGURE 1

STEP 1: 5 0 1 2 3 4 5 6 1/2 1/2 1/2 1/2 1/2 1/2 • REMOVE the PRESS/LEG CABLE from the 880 GYM SYSTEM . Discard the PRESS/LEG CABLE . See FIGURE 1. (NOTE: Remove pulleys for ease of removal.) • NOTE: Follow these steps if assembling the SECOND STACK OPTION to a completely assembled (including cables)...

Page 8 - FIGURE 6

FIGURE 6 STEP 6: 8 • Insert two GUIDE RODS (3) into the STACK BASE (1) as shown on FIGURE 6. (NOTE: If the 880 SHROUD OPTION was purchased, place the GUIDE RODS (3) through the BOTTOM SHROUD BRACKET (found in SHROUD OPTION box)and into the STACK BASE (1) as shown in FIGURE 6. • Slide two WEIGHT STAC...

Page 9 - FIGURE 7; FIGURE 8

FIGURE 7 STEP 7: 0 1 2 3 4 5 6 1/2 1/2 1/2 1/2 1/2 1/2 • CAREFULLY remove the BOOM PLATE from the the REAR UPRIGHT and the FRAME as shown in FIGURE 7. Discard the BOOM PLATE. FIGURE 8 STEP 8: • Swing the GUIDE RODS (3) into the guide rod bushings in the LEFT BOOM BRACKET (2) as shown in FIGURE 8. • ...

Page 10 - FIGURE 9

1 0 0 1 2 3 4 5 6 1/2 1/2 1/2 1/2 1/2 1/2 STEP 9: FIGURE 9 • Unscrew the threaded ends of the WEIGHT STACK CABLE from the WEIGHT STACK SHAFT and remove the two PULLEYS from the BOOM BRACKET. See FIGURE 9. WEIGHT STACK CABLE PULLEY BOOM BRACKET

Page 18 - FIGURE 4; FIGURE 5

1 8 STEP 4: FIGURE 4 • SECURELY assemble the STACK BASE (1) to the BASE FRAME using two 3/8 X 4” BOLTS (15), two previously removed 3/8 X 4-1/4” BOLTS, eight previously removed 3/8” WASHERS and four previously removed 3/8” LOCK NUTS as shown in FIGURE 4. 3/8 X 4” 15 3/8 X 4-1/4” BOLTS BASE FRAME 1 S...

Page 30 - CABLE ROUTING DIAGRAM

3 0 CABLE ROUTING DIAGRAM FIGURE 22 STEP 22: • Carefully route the LONG LEG PRESS CABLE thru the LEG PRESS as shown in FIGURE 22 and assemble the LONG LEG PRESS CABLE to the existing THREADED HOUSING. LONG LEG PRESS CABLE THREADED HOUSING