ParaBody 848 - Manuals - manualsarea.com

Page 2 - IMPORTANT SAFETY INFORMATION; TABLE OF CONTENTS

THERE IS A RISK ASSUMED BY INDIVIDUALS WHO USE THIS TYPE OF EQUIPMENT. TO MINIMIZE RISK FOLLOW THESE RULES ! 1. Before using, read all the warnings and instructionson the use of this machine. Use only for intendedexercise. DO NOT modify the machine. 2. Obtain a medical exam before beginning anyexerc...

Page 3 - Bolt Length Ruler

IMPORTANT NOTES Please note: Tools Required for Assembly * Thank you for purchasing the ParaBody 848 LAT OPTION. Please read these instructions thoroughly and keep them for future reference. This product must be assembled on a flat, level surface to assure its proper function. * Rubber mallet or ham...

Page 4 - PARTS LIST

4 0 1 2 3 4 5 6 1/2 1/2 1/2 1/2 1/2 1/2 PARTS LIST PART # 6 8 2 6 6 0 8 6 8 2 6 9 0 8 6 8 2 5 4 0 8 6 8 2 7 2 0 8 6 8 2 5 5 0 2 6 2 7 5 3 0 2 6 2 7 4 4 0 2 6 5 4 2 4 0 2 6 8 2 4 8 0 1 3 1 0 3 1 0 2 311 6 2 0 1 6 1 7 7 0 0 1 6 4 0 5 2 0 1 6 4 6 7 0 0 1 6 6 9 2 6 0 1 6 8 2 5 1 0 1 KEY 1 2 3 4 5 6 7 8 ...

Page 5 - FIGURE 1; FIGURE 2

FIGURE 1 STEP 1: • SECURELY assemble the one 3/8 X 2-3/4” BOLT (25), two 3/8” WASHERS (19), and one 3/8” LOCK NUT (20) to the STAND (3) as shown in FIGURE 1. • Assemble two 2” SQ. COVER CAPS (14) onto the ends of the STAND (3) as shown in FIGURE 1. • Insert two 3 X 2” END CAP (15) into the ends of t...

Page 7 - FIGURE 5

7 STEP 5: FIGURE 5 • Slide the CARRIAGE (5) over the UPRIGHT (2) as shown in FIGURE 5. • Assemble the STAND (3) to the UPRIGHT (2) as shown in FIGURE 5. 1 3 5 2 • Assemble the BASE (1) to the UPRIGHT (2) as shown in FIGURE 5.

Page 8 - FIGURE 6

STEP 6: FIGURE 6 • SECURELY assemble the BASE (1) to the UPRIGHT (2) using one 1/2 X 3” BOLT (27), two 1/2” WASHERS (21) (slide front washer INSIDE of tube) , and one 1/2” LOCK NUT (22). See FIGURE 6. • Insert one 3 X 2” END CAP (15) and one 2” SQ. END CAP (13) into the ends of the UPRIGHT (2) as sh...

Page 9 - FIGURE 7

9 STEP 7: FIGURE 7 • Route the CABLE (9) through the UPRIGHT (2) as shown in FIGURE 7. • SECURELY assemble three 3-1/2” PULLEYS (11) into the slots of the UPRIGHT (2) using three 3/8 X 2-3/4” BOLTS (25), six 3/8” FLANGE SPACERS (31), and three 3/8” LOCK NUTS (20) as shown in FIGURE 7. (NOTE: Make su...

Page 10 - FIGURE 8

1 0 STEP 8: FIGURE 8 23 3/8 X 2” 19 19 20 9 8 29 2 5 • Place one 3-1/2” PULLEY (11) into the loop of the CABLE (9) below the second and third PULLEY of the UPRIGHT (2) as shown in FIGURE 8. • LOOSELY assemble two 3/16 X 1-3/4 X 5-1/4” PLATES (8) to each side of the 3-1/2” PULLEY (11) using one 3/8 X...

Page 11 - FIGURE 9

11 STEP 9: FIGURE 9 23 3/8 X 2” 19 19 20 9 11 2 • Route the end of the second CABLE (9) through the slot on the UPRIGHT (2) then SECURELY assemble one 3-1/2” PULLEY (11) to the UPRIGHT (2) using two 3/8 X 2-1/2” BOLTS (24), two 3/8 X 3/8” SPACERS (30), four 3/8” WASHERS (19), and two 3/8” LOCK NUTS(...

Page 17 - LIMITED WARRANTY

1 7 NOTES: LIMITED WARRANTY ParaBody extends the following LIMITED WARRANTY to the original owner of the ParaBody products. The Warranty terms apply to IN HOME USE ONLY. 1. LIMITED WARRANTY ON FRAME AND WELDS. If the frame of the ParaBody product or a weld should crack or break, it will be repaired ...