ParaBody 435104 - Manuals - manualsarea.com

Page 2 - BOLT LENGTH RULER:; Bolt Length Ruler; BOLT LENGTH; WELCOME TO THE WORLD OF

IMPORTANT NOTES Please note: Tools Required for Assembly * Thank you for purchasing the 435104 Leg Press Adapter Kit. Please read these instructions thoroughly and keep them for future reference. This product must be assembled on a flat, level surface to assure its proper function. * Rubber mallet o...

Page 3 - FIGURE 1; PARTS LIST

STEP 1 FIGURE 1 PART # 6747603 3116202 3108102 6427101 3118701 3201501 6271801 6747901 KEY 1 2 3 4 5 6 7 8 QTY 1 2 1 1 1 1 1 1 PART # 3102701 3102501 3102802 3102502 3102801 3102902 3102910 3102909 DESCRIPTION 3/8” HEX NUT 3/8” WASHER 3/8” LOCKNUT 1/2” WASHER 1/2” LOCKNUT 3/8 X 2-1/4” BOLT 1/2 X 3” ...

Page 4 - FIGURE 2

STEP 2 FIGURE 2 4 REAR SHROUD • If the 445104 SECOND STACK OPTION is not installed, the rear SHROUD opening must be removed. Apply pressure to the bottom of the SHROUD where the “V” groove is and carefuly remove the weight stack opening on the SHROUD as shown in FIGURE 2. 0 1 2 3 4 5 6 1/2 1/2 1/2 1...

Page 5 - FIGURE 3

FIGURE 3 STEP 3 • Remove two 3/8” LOCK NUTS, two 3/8” HEX NUTS, two SWIVEL SNAP (68) (keep elastic cords attached), two 3/8 X 1/2” SPACERS, and one 3/8” THREADED SHAFT from the bracket on the BASE as shown in FIGURE 3. BASE 5 HEX NUT • Discard the two 3/8 X 1/2” SPACERS. HEX NUT 3/8 X 1/2” SPACERS (...

Page 6 - FIGURE 4; FIGURE 5

6 FIGURE 4 BASE HEX NUT 3/8” LOCK NUT 2 STEP 4 • Assemble the two previously removed 3/8” HEX NUTS, two previously removed SWIVEL SNAPS, one 3-1/2” PULLEY (2), and two previously removed 3/8” LOCK NUTS to the previously removed 3/8” THREADED SHAFT as shown in FIGURE 4. HEX NUT 3/8” LOCK NUT 0 1 2 3 ...

Page 7 - FIGURE 7A; FIGURE 6

FIGURE 7A (WITHOUT 445104 SECOND STACK OPTION) STEP 7A 3/8” LOCK NUT TOP BOOM 9 3/8” HEX NUT • SECURELY assemble one 2” PULLEY (5) to the 3/8” THREADED SHAFT on the TOP BOOM using one previously installed 3/8” WASHER, one 3/8” HEX NUT (9) and one previously installed 3/8” LOCK NUT as shown in FIGURE...

Page 8 - FIGURE 8

FIGURE 7B (WITH 445104 SECOND STACK OPTION) STEP 7B • If the 445104 SECOND STACK OPTION is NOT installed proceed to STEP 8 . TOP BOOM 3/8” X 1” 16 10 5 11 3/8” LOCK NUT • SECURELY assemble one 3/8 X 1” BOLT (16), one 3/8” WASHER (10), one 2” PULLEY (5) and one 3/8” LOCK NUT (11) to the bracket on th...

Page 9 - FIGURE 9

9 STEP 9 FIGURE 9 • Route LEG PRESS CABLE (8) around the 3-1/2” PULLEY on the LEG PRESS and UNDER the 3-1/2” PULLEY on the FRONT LEG (1) as shown in FIGURE 9. • SECURELY attach the LEG PRESS to the FRONT LEG (1) using two 1/2” X 3” BOLTS (15), two 1/2” WASHERS (12), and two 1/2” LOCK NUTS (13). See ...

Page 11 - DETAIL 11

11 STEP 11 DETAIL 11 FIGURE 11 SEE DETAIL 11 LEG CABLE LAT CABLE PRESS CABLE D-RING • Run the LEG PRESS CABLE through the correct hole on the d-ring and attach one KEYHOLE CLEVIS to the end of the LEG PRESS CABLE. See FIGURE 11 & DETAIL 11. (NOTE: If the 445101 SECOND STACK kit is installed, eve...