ParaBody 220 - Manuals - manualsarea.com

Page 2 - IMPORTANT SAFETY INFORMATION; TABLE OF CONTENTS

THERE IS A RISK ASSUMED BY INDIVIDUALS WHO USE THIS TYPE OF EQUIPMENT. TO MINIMIZE RISK FOLLOW THESE RULES ! 1. Before using, read all the warnings and instructionson the use of this machine. Use only for intendedexercise. DO NOT modify the machine. 2. Obtain a medical exam before beginning anyexerc...

Page 3 - BOLT LENGTH RULER:; Bolt Length Ruler; BOLT LENGTH

IMPORTANT NOTES Please note: Tools Required for Assembly * Thank you for purchasing the ParaBody 220 Gym System. Please read these instructions thoroughly and keep them for future reference. * Rubber mallet or hammer* 3/4” wrench* 9/16” wrench* Ratchet with 3/4” and 9/16” sockets* 5/32” Allen wrench...

Page 5 - PARTS LIST

5 PARTS LIST 0 1 2 3 4 5 6 1/2 1/2 1/2 1/2 1/2 1/2 PART # 7 0 0 5 0 0 8 7 0 0 5 7 0 8 6 9 9 4 6 0 8 7 0 0 5 3 0 8 7 0 0 5 2 0 8 7 0 0 5 4 0 8 7 0 0 5 5 0 8 6 9 9 9 7 0 8 7 0 0 5 1 0 8 7 0 0 5 8 0 8 7 0 0 5 6 0 8 6 9 4 0 8 0 8 6 9 9 4 7 2 1 6 5 4 9 3 0 1 6 1 9 4 6 0 1 6 5 2 3 4 0 1 7 0 0 6 2 0 2 7 0 ...

Page 6 - FIGURE 1

FIGURE 1 6 STEP 1: • LOOSELY assemble the FOOTPLATE (62) to the lower holes in the FRAME (1) using one 3/8 x 3” BOLT (29) and one 3/8 LOCKNUT (34) 1 3 4 3 0 2 62 3/8 X 3-3/4 2 9 4 1 34 3 • LOOSELY assemble two BASE PLATES (3) to the FRAME (1) and BASE (2) using four 3/8 X 3-3/4” BOLTS (30) and four ...

Page 8 - FIGURE 4; FIGURE 5

• Insert two GUIDE RODS (16) into the BASE (2) as shown on FIGURE 4. (NOTE: If the 220 SHROUD OPTION was purchased, place the GUIDE RODS(16) through the BOTTOM SHROUD BRACKET (FOUND IN THE SHROUD KIT BOX ) into the BASE (2), as shown in FIGURE 4. • Using EXTREME CARE slide all fifteen WEIGHT PLATES ...

Page 10 - FIGURE 8

FIGURE 8 8 4 9 2 9 3 6 9 3 4 STEP 8: • Place PRESS ARM (8) into PRIMARY PIVOT (9) and securely tighten using two 3/8 X 3” BOLTS (29), four 3/8” FLAT WASHERS (36) two 3/8” LOCK NUTS (34) • Insert and tighten two 3/8” LOCKING SPRING PINS (49) into PRESS HANDLES (6), (7). 3/8 X 3” 1 0 • Lock PRESS ARMS...

Page 11 - FIGURE 9

FIGURE 9 11 0 1 2 3 4 5 6 1/2 1/2 1/2 1/2 1/2 1/2 STEP 9 • Assemble the PRIMARY PIVOT (9) of the PRESS ARM ASSEMBLY to the top of the FRAME (1) using 1/2 X 8” BOLT (33), two 1/2” FLAT WASHERS (37) and 1/2” LOW HT LOCK NUT (35). IMPORTANT! DO NOT TIGHTEN YET • SECURELY TIGHTEN ALL FRAME CONNECTION BE...

Page 14 - ILLUSTRATION A

ILLUSTRATION A NOTE: IF YOU PURCHASED A LEG PRESS, PLEASE REFER TO THE CABLE ROUTING INSTRUCTIONS INCLUDED WITH THE LEGPRESS KIT 1 4 • ILLUSTRATION “A” used as cable routing reference for steps 13-16

Page 23 - LIMITED WARRANTY

2 3 NOTES: LIMITED WARRANTY ParaBody extends the following LIMITED WARRANTY to the original owner of the ParaBody products. The Warranty terms apply to IN HOME USE ONLY. 1. LIMITED WARRANTY ON FRAME AND WELDS. If the frame of the ParaBody product or a weld should crack or break, it will be repaired ...