Panasonic WVCP304 - Manuals

Panasonic WVCP304 – Manual in PDF format online.

Manuals:

Manual

Manual Panasonic WVCP304

Summary

Page 2 - Preface; About the user manuals; Trademarks and registered trademarks

2 Preface About the user manuals The operating instructions of the camera consist of 2 sets: these operating instructions (PDF) and Installation Guide.This document explains how to configue the settings of the camera.Refer to the installation guide for further information about how to install the ca...

Page 3 - Contents; Screen transition diagram

3 Contents Preface .......................................................................................................................................... 2About the setup menus ................................................................................................................ 4 List...

Page 4 - About the setup menus; List of setup menu

4 About the setup menus Performing each setting item in the setup menu should be completed in advance to use this unit.Perform the settings for each item in accordance with the conditions of the camera shooting area. List of setup menu Setup item Description CAMERA ID This item specifies the camera ...

Page 5 - Basic operation

5 Screenshot 2 The setup mode changes to "ENABLE", and the setup menu becomes ready to be set. Step 3 Move the cursor to the item to be set, and press the [SET] button. Screenshot 1 Hold down the [SET] button for about 2 sec-onds to call up the top screen of the setup menu. Step 1 Press the ...

Page 6 - Screenshot 3; • If the top screen of the setup menu is

6 Screenshot 3 The selected setup screen in the setup menu appears on the screen. Note: • If the top screen of the setup menu is called up with the operation buttons while the camera is operated, the setup mode is always "DISABLE" to prevent operation errors. To perform settings in the setup...

Page 11 - of a lens with fixed iris or manual iris.; Back light compensation function; Follow the procedure below.

11 2 Light quantity control method selection [ALC/ELC] The method of controlling the quantity of light is selected from the following in accordance with the lens to be used. ALC (default): The iris of the lens is automatically adjusted in accordance with the brightness of a subject. Select "ALC&...

Page 13 - Electronic sensitivity enhancement setting [SENS UP]

13 Note: • When "SENS UP" is set to the AUTO mode, “AGC” cannot be set to “OFF”. 5 Electronic sensitivity enhancement setting [SENS UP] Use of the electronic sensitivity enhancement function increases the light sensitivity of the CCD, and accordingly the image becomes brighter. The magnifica...

Page 14 - Manual fine adjustment of white balance; The fine adjustment screen appears.

14 Step 1 Set "WHITE BAL" to "AWC" and press the [LEfT ] button to change to "AWC → PUSH SET". Step 2 Press the [SET ] button and adjust the white balance. "AWC → PUSH SET" is reversely high- lighted during adjustment. When the reversely highlighted display is restore...

Page 15 - Digital noise reduction function setting [DNR]; “CAMERA SETUP” screen

15 Step 4 Move the cursor to "POSITION" and press the [SET ] button. Step 5 Press the [uP], [dOwN], [rIghT ] and [lEfT ] buttons to move to the upper-left part of the area to be set, and press the [SET ] button. Step 6 Press the [uP], [dOwN], [rIghT ] and [lEfT ] buttons to move to the lower...

Page 16 - Step 2; • There may be repeated switching between color and black-an

16 CP310 CP310 CP300 AUTO: Similar to the basic functions of AUTO1, but does not change the IR filter. Switches to black-and-white images when brightness (illuminance) around the camera is lower than approx. 0.1 lx. OFF (default): Displays color images. Note: • CP310 CP310 CP300 When “AUTO1” or “AUT...

Page 17 - Set motion detection

17 Note: • Images may not be displayed appropriately without burst signals when camera images are displayed in the black-and-white mode depending on a monitor or VCR model to be used. In such a case, set the burst signal output to "ON". 9 VMD setting [VMD] The VMD function allows the camera ...

Page 19 - Setting of scene change detection

19 Step 6 Move the cursor to “Level”. Use the [RIGHT ] or [LEFT ] button to adjust the level. Repeat step 5 and 6 to adjust to optimal level. Step 7 Move the cursor to “DWELL TIME ”. Select the dwell time from the following.2 S (default)/5 S /10 S /30 S Alarm signal will be issued once a continuousl...

Page 22 - The zoom setting screen appears.

22 When "ON" is selected, the zoom factor and the panning/tilting settings can be configured. Follow the procedure below. ** EL-ZOOM ** PUSH SET PUSH SET ** EL-ZOOM ** PUSH SET PUSH SET ** EL-ZOOM ** PUSH SET PUSH SET ZOOM PAN/TILT ZOOM PAN/TILT ZOOM PAN/TILT U ZOOM D U ZOOM D L PAN R “SYSTE...

Page 23 - • Moire (interferenc

23 The special menu setup is performed including the setting of the camera image quality and the communication configuration when a decoder is used. The following settings are to be config-ured on the "SPECIAL SETUP" screen displayed from the top screen. Refer to page 5-6 for how to call up ...

Page 26 - Camera language selection [LANGUAGE SETUP]

26 The language selection can be made on the "LANGUAGE SETUP" screen displayed from the top screen. Refer to page 5-6 for how to call up the screen. Move the cursor to “LANGUAGE”, use the [RIGHT] or [LEFT ] button to select the target lan-guage, then move the cursor to “SET”, and press the [...

Page 27 - Electronic zoom ON; Shortcut operation

27 Use of a system controller with the "Camera function" button allows users to perform the shortcut settings with use of the numeric keypad and camera function button. The available shortcut operations with this unit are shown as follows. System controller operation Setting contents [9] + [...

Page 28 - Panasonic Canada Inc.

Panasonic System Communications Company of North America,Unit of Panasonic Corporation of North America www.panasonic.com/business/For customer support, call 1.800.528.6747Three Panasonic Way, Secaucus, New Jersey 07094 U.S.A. Panasonic Canada Inc. 5770 Ambler Drive, Mississauga, Ontario, L4W 2T3 Ca...