Panasonic WJ-HD220 - Manuals

5 PREFACE The Digital Disk Recorder WJ-HD220 is designed for usewithin a surveillance system and is a combination of a harddisk recorder and an 8-input video multiplexer. It recordsnearly 8 600 hours of picture and audio data selectively ona field basis with fine quality (FQ). Besides recording and ...

6 PRECAUTIONS • Refer all work related to the installation of this product to qualified service personnel or system installers. • Prevent condensation from forming on the surface of the hard disk. Wait until the dew evaporates in any ofthe following cases. The recorder is moved to a place significan...

7 MAJOR OPERATING CONTROLS AND THEIR FUNCTIONS ■ Front View OPERATE ALARM SUSPEND RESET HDD FULL ERROR OSD MULTISCREEN SELECT ZOOM TIMER DST REMOTE LOCK SEQUENCE ALARM SERCH STOP PLAY MODE SELECT SETUP /ESC PLAY TIME&DATE SEARCH REC STOP SPOTMULTI CAMERA SELECT ALARM RECALL REC PUSH— PAUSE SET D...

9 While opening the time and date search window(TIME&DATE SEARCH): Pressing the JogDial moves the cursor to the nextposition in the window.Rotating the JogDial increases or decreases theparameter.After specifying the date and time, press the [PLAY]button to start playback. When operating alarm r...

10 SIGNAL GND POWER DATA 10/100BASE-T MODE RS-232C MULTI SCREEN OUT SPOT OUT 1 1 ALARM/REMOTE OFF ON 2 2 3 3 4 4 5 5 6 6 7 7 8 8 OUT VIDEO OUT AUDIO IN IN #1 #3 #0 #2 #4 #6 #9 $0 #5 #7 #8 $1 $2 $3 $4 ■ Rear View #0 Audio Input Connector (AUDIO IN) An RCA standard jack that accepts an unbalanced –10 ...

11 INSTALLATION ● Warning This installation should be made by qualified service personnel or system installers. ● Notes Places to avoid • Direct exposure to sunlight or near a source of heat such as a radiator.• Very dirty and dusty places. Places subject to strong vibrations.• Near a transformer, d...

12 ■ Mounting in the Rack 1. Remove the four rubber feet by removing the five screws on the bottom of the unit. 2. Place the rack mounting brackets on both sides of the unit and tighten with the six supplied screws (M3 x10). 3. Install the unit with the rack mounting brackets in the rack by using fo...

13 CONNECTIONS & DIP SW SETTING System Composition & Connections Three system compositions are introduced depending on the camera type and other peripherals connected. <Basic System> Ordinary system-cameras are connected in combination with the multiscreen and spot monitors, microphone...

16 ■ Connection with the CameraSite ● System Camera Connection Connect system cameras to VIDEO IN 5-8. ● Data-multiplex Camera Connection Connect combination cameras directly to VIDEO IN 1-4.When connecting to VIDEO IN 5-8, use a Data MultiplexUnit as shown below. ■ Connection with the Monitors Conn...

18 ■ Serial Port Connections ● RS-232C Connection A 9-pin connector is provided with the recorder to communicate with the PC via the RS-232C interface. ● PS • Data Connection Note the following when connecting the recorder with PS • Data devices. 1. Place the recorder in the middle of the chain when...

20 DIP Switch Setting The 6-bit DIP switch is used as follows. #1 through #4: System mode setup#5 and #6: DATA port termination ■ System Mode ■ DATA Port Termination Termination switch positions depend on the system compo-sition. MODE 1 2 3 4 5 6 O N Termination 2 Termination 1 System Mode Setup MOD...

21 SETUP PROCEDURES ■ Prior to Setup ● Turning On the Power 1. Plug the power cord into the AC outlet. 2. Turn on the power switch on the rear panel. The oper- ate LED lights up. An HDD check and a system checkwill be carried out while displaying respective mes-sages.Power-on recording will start if...

22 ● Displaying WJ-HD220 (MAIN MENU) 1. Confirm that the camera and peripherals are connected correctly and securely. 2. Turn on the power switches of all system components. 3. Hold down the [STOP] button for 2 seconds. The WJ- HD220 MAIN MENU appears. ● Buttons and Dials Used for Setup [ D up] butt...

23 ● Menu Tree The figure shows the hierarchy of menu windows. WJ-HD220 MAIN MENU TIME ADJUST SETUP VMD SETUP SERIAL PORT SETUP SEQUENCE SETUP CAMERA VIEW SETUP SYSTEM LOG CAMERA SYSTEM SETUP VMD AREA SETUP MULTI SEQ SETUP SPOT SEQ SETUP SYSTEM SETUP CAMERA TITLE DISPLAY SETUP EXT REC SETUP REC SETU...

24 ■ Initializing You can initialize all disk contents including image dataand/or setup data. ● Initializing All Contents & Setup Data Warning! The following are irrevocable procedures. We strongly recommend that you copy important pic-tures from the hard disk. 1. Press the [REC STOP] button or ...

25 ■ Main Menu (WJ-HD220 MAINMENU) The main menu is located at the top of the menu tree fromwhere every menu window starts. 1. Hold down the [SETUP/ESC] button for 2 seconds. The main menu appears. 2. Select a setup menu you wish to program using the [ D ] or [ C ] button, and press the [SET] (JogDi...

28 3. Select the parameter with the JogDial, and press the JogDial.The default is REC. REC: The channel is recorded in alarm recording, timer recording and manual recording mode. ALM-ONLY: The channel is recorded only when the alarm operates. 4. Repeat steps 2 and 3 until all channels are set. 5. Pr...

32 ● Password Lock Setup (PASSWORDLOCK) A five-digit password is entered to protect all settings,recorded pictures, and operating status against erroneousoperation and tampering. Settings alone can be also pro-tected from unauthorized access. While the LOCK indicatoron the front panel is on, a messa...

41 ● HTTP Port (HTTP PORT) Set an HTTP port number.The default is 80. Available port numbers: From 00000 to 65535, except the "well-known port" numbers assigned by IANA(Internet Assigned Numbers Authority) ● Dynamic Host Configuration Protocol(DHCP) Dynamic Host Configuration Protocol is ena...

45 OPERATING PROCEDURES Controlling Video Inputs &Monitors Operations on the front panel can control video inputs onthe spot monitor or multiscreen monitor. ■ On the Spot Monitor ● Selecting the Spot Monitor 1. Press the [SPOT/MULTI] button to turn the LED in the button on. The spot monitor is r...

46 ■ On the Multiscreen Monitor ● Selecting the Multiscreen Monitor 1. Press the [SPOT/MULTI] button to turn the LED in the button off. The multiscreen monitor is ready to be oper-ated. 2. Follow the descriptions below for each monitoring mode on the multiscreen monitor. ● Viewing a Single Live The ...

47 ● Connected Alarm Sensors A maximum of eight sensors can be connected to the termi-nals on the rear panel. Sensors may be installed in suchplaces as parking lots or reception desks where cars andvisitors come and go. ● Built-in Motion Detector The recorder detects motion for each of the eight vid...

48 ● Monitor Display There are two monitoring modes, alarm associated (SPOT)mode and alarm ignore (OFF) mode, depending on theselection for MONITOR MODE in the ALARM SETUP menu.Typical cases are described below for each setup. Alarm Associated Mode • The image of the alarmed input is displayed on th...

49 ● Auto Reset The activated alarm event is reset when the AUTO RESETtime has elapsed, or the lost video has been recovered. The ALARM indicator changes from blinking to a steadylight. ● External Reset The activated alarm event except video motion detection, isreset when the recorder receives an ex...

50 Recording Notes: • When SIMUL REC&PLAY (simultaneous recording and playback) is set to OFF in the setup, any recording willstop playback and start the recording. Playback isunavailable while recording. • When set to ON, recording is available while playing back. • The recording rate will degr...

51 Orange: The channel image is not displayed. Yellow: The channel image is displayed. The multiscreen monitor displays the recording imageswhile the corresponding input indicators on the frontpanel light in yellow. 2. Hold down the [REC STOP] button for 2 seconds to stop recording. The REC indicato...

52 3. Rotate the JogDial clockwise to move forward in the recorded data or counter-clockwise to move backward. The more turns you rotate the JogDial, the faster theskip speed will be. 4. Press the [STOP] button to stop playback. ■ Step Playback A minute search is made for a desired picture field by ...

53 6. Repeat from step 1 to search for another time and date or press the [TIME&DATE SEARCH] button to cancelthe function. Pressing the [STOP] button will also endthe searching. Note: Searching may take the recorder 18 seconds at worst ■ Multiscreen Playback You can view a multiple playback imag...

54 Lock/Unlock Buttons ■ Password Verification When a locked button is pressed, the key locked warningappears on the monitor for 2 seconds, then it changes tothe password prompt. 1. Enter your five-digit password using the [CAM SELECT] buttons (1-8). The buzzer shortly beeps once, and theentered dig...

56 ■ System Requirements Your personal computer must meet the following minimum requirements. OS: One of the following operating systems: Windows98 Second EditionWindows2000Windows Millennium EditionWindowsXP Professional or Home Edition Browser: One of the following browser software: Microsoft Inte...

57 ■ Connection System connection examples are shown. <Direct Connection with a PC> • Connection with a Client PC via Hub <System Expansion> A maximum of four PCs can access the recorder at a time. WV- CL920 Digital Disk Recorder Camera Personal Computer Ethernet Cross Cable OPERATE ALAR...

58 ■ Main Page and Control Panel Start your PC WWW browser. Type http://192.168.0.10/ (orthe IP Address set for WJ-HD220) / in the URL ( U niform R esource L ocators) space. The browser displays the Main Control Panel of the WJ- HD220 homepage as shown in the figure. Notes: • Specify "http//:192...

59 ■ To Access Setup Menus There are fourteen setup menus to adapt the WJ-HD220 toyour requirements. 1. On the Main Control Panel , click the [SETUP MENU] button. The setup menu opens. 2. Click the buttons to open the respective windows. <Main Setup Menu> TIMER SETUP: Specifies the schedule an...

61 • Even if preset to 30 or 15 FPS, the actual recording rate may drop to 7.5 FPS at worst while busy multi task suchas playback, remote-access playback, remote-accesslive image, FTP access, multi-split display, or videomotion detection are carried out simultaneously.The status display will indicat...

63 TYPE2 12H: Time and date are displayed in two lines in the AM-PM system. OFF: Time & date display is disabled. 8 Time and Date Position (TIME&DATE POSITION) Right-Lower: Displays time & date in the lower right corner. Right-Upper: Displays time & date in the upper right corner. Le...

68 ■ Camera System Setup(CAMERA SYSTEM SETUP)(only for PS • DATA) 8 Camera Number (CAMERA No.) The camera number assigned to the port is used whena system controller accesses the camera. Assignable numbers: From 1 to 128, must be unique in the chain. 8 Compensation level (COMPENSATION) Video signal ...

69 8 Domain Name Service (DOMAIN NAME SERVICE) OFF: Disables DNS, only IP address usable. MANUAL: Enables DNS. AUTO: Enables DNS. Domain Name (DOMAIN NAME) Enter from the keyboard. DNS Server Address (DNS SERVICE ADDRESS) Enter from the keyboard. 8 Dynamic DNS (DYNAMIC DNS) OFF: Does not use DDNS. O...

70 ■ Switcher Setup (SWITCHERSETUP) This window specifies sequence setups only for the WJ-HD220. The browser's sequence is set up in LIVESEQUENCE SETUP on page 77. 8 Common Setup (COMMON SETUP) Multiscreen monitor Start Display (START DISPLAY(MULTI))Spot monitor Start Display (START DISPLAY(SPOT)) T...

72 ■ System Information (SYSTEMINFORMATION) 8 HDD Hour Meter (HDD HOUR METER) Each meter shows how many hours the digital hard diskrecorder has been operated in playback, recording andidle. The built-in HDD needs replacement when thehour meter reads around 30 000 H. 8 HDD Capacity (HDD CAPACITY) The...

74 ■ User Setup (USER SETUP) A maximum of 16 users can be registered. 8 User Authorization (USER AUTHORIZATION) OFF: Allows free access. ON: Verifies the password and access level for a maxi- mum of sixteen users. Click the [SET] button. 8 User Name (USER NAME) Enter from the keyboard. The default i...

76 ■ Mail Setup (MAIL SETUP) 8 Alarm Mail Setup (ALARM MAIL SETUP) Sending Mail (SEND MAIL) OFF: Does not send. ON: Sends an e-mail to a maximum of four recipi- ents when an alarm operates. Attaching Alarm Image (ATTACH ALARM IMAGE) OFF: Does not attach. ON: Attaches the image of the alarmed channel...

77 ■ Network Video Setup(NETWORK VIDEO SETUP) 8 Live & Playback Image Setup (LIVE & PLAYIMAGE SETUP) Video Rate (VIDEO RATE) Applicable rates: FAST, MIDDLE, SLOW, VERY SLOW Click the [SET] button. 8 Live Sequence Setup (LIVE SEQUENCE SETUP) Use Sequence (USE SEQUENCE) OFF: Does not run the s...

78 q Main Control Panel Tab Opens the main control panel. w Alarm List Tab Opens the alarm list. e Network Status Display LIVE, LIVE SEQ, PLAY, REV PLAY, >> (FF), << (REW).PAUSE and AL (playback of alarm record) are dis-played. r Channel Number Display (CH) The channel number of the imag...

80 ■ Main Control Panel 8 Camera Selection Button (Camera Select) Click any of the buttons. The selected camera channel will be displayed in theimage area. 8 Multiscreen Selection Button (Multiscreen Select) Clicking the button displays the respective multiscreen. 8 Live Sequence Button (LIVE SEQUEN...

81 8 Camera Control View Button (CAMERACONTROL VIEW) The camera control buttons appear on the bottom of thescreen when you click the [CAMERA CONTROL VIEW] but-ton. These buttons enable you to adjust images of combi-nation cameras. ZOOM (WIDE/TELE) buttons zoom the image in or out. FOCUS (FAR/NEAR/AU...

82 ■ Alarm List Clicking the alarm list tab on the main control panel opensthe list.Alarm events are listed with event numbers, dates, channelnumbers, and event types. Click a line to play back the recorded image of the event. CH SORT rearranges the listing order to start with the camera channel you...

84 Cannot search alarm image in the list Enter a date that is a little older than theone you wish to search. Old image data are overwritten andcannot be searched. Old records were discarded. Specified date may be later. DISK END MODE is set to CONTINUE. Over 9 999 of alarm events arose. Slow image r...

86 SPECIFICATIONS General Power Source Required: 120 V AC, 60 Hz Power Consumption: 45 W Ambient Operating Temperature: +5 °C - +45 °C (41 °F - 113 °F) Ambient Operating Humidity: Less than 85 % Dimensions: 420 mm (W) x 44 mm (H) x 350 mm (D)16-9/16" (W) x 3-7/16" (H) x 13-3/4" (D) Weigh...

87 STANDARD ACCESSORIES Rack Mounting Bracket ............................................................... 2 pcs.Screw for Rack Mounting Bracket (M3x10) ................................. 6 pcs.Absorber ...................................................................................... 4 pcs.Sl...

88 Item SHIFT SETUP FUNCTION Step playback REW Alarm record playback Setup menu display on/off The top of the oldest record will beaccessed. Jump to oldest UP L R UP DOWN R WV-CU360 APPENDIX ■ Remote Control from System Controller A system controller having PS • Data capability can control the WJ-HD...

90 ■ RS-232C Communication Protocol The following pages detail the elements for communication between the Digital Disk Recorder and the personal computer. Besure to select RS-232C for PROTOCOL in the COMMUNICATION SETUP window. For BAUD RATE, DATA BIT and PARITY set-tings, refer to COMMUNICATION SET...

91 ● Command Table Basic Operation Item Transmission Command (ASCII) Response (ASCII) Parameter (ASCII) Fast Forward to the end OFF OFF Pause OPA OPA Play OPL OPL Recording ORC ORC Rewind to the top ORW ORW Skip&Play Forward OSF:n OSF n=0F Normal speedn=1F x2 speedn=2F x5 speedn=3F x50 speedn=5F...

94 ■ HDD Maintenance ● When to Maintain HDD HDD maintenance is required in the following cases. • When FULL indicator lights up• When ERROR indicator lights up• When an optional hard disk is added• When you wish to format the HDD or to remove link• When HDD reaches its life time (around 30 000 hours...

95 ● When Error Indicator is Lit Refer to your dealer for servicing when this happens. 8 HDD Check The recorder checks the hard disk when the recorder isturned on, or when the HDD CHECK time specified inthe menu setup comes during operation. The recorder warns you of any error detected as fol-lows. ...

96 You can implement any of the following operations as necessary. REMOVE LINK: Logically removes the HDD link. HDD FORMAT: Formats the HDD. RESTART: Closes the menu, and restarts the recorder. The menu can also be displayed manually when you need to format the HDD or remove the logical link. 1. Tur...

97 8 Formatting HDD (HDD FORMAT) This command initializes the HDD format and is applic-able to HDDs of *, ERR, or ADD status. Caution: Formatting is an irreversible procedure. We strongly recommend that, before formatting, youeither save the recorded data into the server via thenetwork, or you save ...

99 ■ Mail Contents The recorder sends e-mails to the specified addresseswhen SEND MAIL is set to ON. An e-mail contains the fol-lowing information. ● Alarm Notice Mail A JPEG image file with an HTML file will be sent when specified to attach. WJ-HD220 (Sender IP Address) STATUS REPORT DATE: Jan31.03...

100 ■ Network Security ● WJ-HD220 Security Function Host/User Authentication Access can be limited by setting the authentication function to ON in the menu setup. Note: Be sure to change the password from the default setting "admin" to your own. Changing the HTTP Port Number Changing the por...

101 Type POP3 server error SMTP server error Connection error Internal error Message Authentication error (POP3) Cannot connect to POP3 server Connection error to DNS server (Cannot resolve server name) Cannot connect to SMTP server MAIL FROM command error RCPT TO command error Undefined error Detai...