Panasonic WJ-HD100 - Manuals

5 PRECAUTIONS • Refer all work related to the installation of this product to qualified service personnel or system installers. • Avoid condensation on the surface of the hard disk. Wait until the dew evaporates if any of the followingcase takes place. The recorder is moved to a place significantly ...

6 MAJOR OPERATING CONTROLS AND THEIR FUNCTIONS ■ Front View OPERATE TIMER HDD ALARM SUSPEND DAYLIGHT SAVINGS FULL LOCK MEMORY CARD DISPLAY SELECT STOP PLAY REC PUSH– PAUSE SET ALARM SEARCH STEP REW/FF PLAY MODE SELECT / / / / SETUP/ESC q w e r t y u i o !0 !1 !2 !3 !4 !5 !6 !7 !8 LCD CONTRAST Digita...

7 !7 REW/FF and Up Button [REW/FF 1 / 2 ] [ D ] Press this button to rewind or fast-forward the recordedfield. The LED lights in the REW/FF mode.Press this button to move the cursor upward in a setupmenu on the monitor. !8 JogDial [PUSH – ❚ ❚ PAUSE] [SET] Press the JogDial to pause or restart playba...

9 INSTALLATION ■ Mounting in the Rack 1. Remove the four rubber feet by removing the four screws on the bottom of the unit. 2. Place the rack mounting brackets on both sides of the unit and tighten with the six supplied screws (M3 x10). 3. Install the unit with the rack mounting brackets in the rack...

10 CONNECTION ■ Basic Connection To select the recording mode from an external device connected to the EXT REC mode switch, the JOG/EXT REC parameter inthe REC SETUP menu must be set to EXT REC. SIGNAL GND ALARM SERIES RECORD TIME ADJUST REMOTE MODE DATA RS-232C VIDEO OUT IN OUT IN AUDIO MONITOR OUT...

12 Recommended video multiplexers are Panasonic’s WJ-FS series or similar models having specifications as follows. • Switching recognition signal is located within 8H prior to the end of vertical blanking.• A camera switching rate of 4/60 seconds or more is available. See SERIES RECORDING in APPENDI...

13 8 7 6 5 4 3 2 1 REMOTE/ALARM IN CONTROL INALARM OUTRECOVER OUTRESET IN G G G G G G G G G G G +24V NC NO To Alarm Indicator External device NC: Normally ClosedNO: Normally Open Relay ALARM G RECALL OUT RECOVER OUT RESET IN IN Digital Disk RecorderWJ-HD100 ■ Alarm Terminal Connection A connection e...

ALARM RECOVER OUT 14 MODE ON Termination Unit Address/Initializing Alarm Out Polarity 1 2 3 4 5 6 ■ Mode Switch Setting The 6-bit DIP switch on the rear panel is used as follows. #1 through #4: For setting the unit address or initializ- ing the setup data #5: Termination for communication lines #6: ...

15 SETUP PROCEDURES ■ Prior to Setup ● Turning On the Power ● Turning Off the Power 1. Plug the power cord into the AC outlet. 2. Turn on the power switch on the rear panel. The operate LED lights, and the date, time and operat-ing status are displayed on the LCD. Power-on recording will start if [T...

16 ● Displaying the SETUP MENU 1. Confirm that the camera and peripherals are connected correctly and securely. 2. Turn on the power switches of all system components. 3. Hold down the SETUP/ESC button for 2 seconds or more. The WJ-HD100 SETUP MENU appears on the monitor. ● Buttons and Dials Used fo...

17 ● Setup Menu Sequence The WJ-HD100 provides the following seven setup menus: WJ-HD100 SETUP MENU, SYSTEM SETUP, REC SETUP, ALARMSETUP, INTERNAL TIMER REC, COMMUNICATION SETUP and SYSTEM INFORMATION. Pressing the [ ▲ ] or [ ▼ ] button repeatedly will switch the menu as follows. The item or paramet...

18 ■ Initializing You can either initialize all disk contents including imagedata and setup data, or setup data only. ● Initializing All Contents & Setup Data Warning! The following are irrevocable procedures. We strongly recommend that you copy important picturesfrom the hard disk to CompactFla...

19 ■ WJ-HD100 SETUP MENU ● Clock Setup 001 CLOCK> Set the internal timer to the present time and date.The default value is “JAN 1.00 0:00”. 1. Hold down the [SETUP/ESC] button for 2 seconds to display the setup menu on the monitor. 2. Move the cursor on the monitor to CLOCK with the [ ▲ ] or [ ▼ ...

21 1. Move the cursor to STATUS POSI. with the [ ▲ ] or [ ▼ ] button. 2. Select the desired position with the JogDial. The default is R-LOWER. L-UPPER: Displays the status in the left upper corner. R-UPPER: Displays it in the right upper corner. CENTER: Displays it in the center. L-LOWER: Displays i...

22 ● Password Setup102 PASSWORD LOCK A 5-digit password is entered to protect all settings, record-ed pictures, and operating status, or settings only fromunauthorized access. While the LOCK indicator on the frontpanel is on, the LCD displays the message "Now KeyLocked!" to warn unauthorized...

N/A 24 ■ REC SETUP Picture quality and field rate are selected as a set or indi-vidually. ● Recording Mode 201 REC MODE Select one of the following 5 basic options: super fine (SF,level 10), fine (FQ, level 8), normal (NQ, level 7), long-timerecording (EX, level 5) and optional (SP). If combined wit...

26 1. Move the cursor to DISK END MODE with the up [ ▲ ] or down [ ▼ ] button. 2. Rotate the JogDial to select the desired parameter. The default is STOP. [STOP]: Stops recording until a mode other than [STOP] is selected. [CONTINUE]: Old data is automatically overwritten from the disk start. [ALM C...

27 ■ ALARM SETUP The digital disk recorder accepts an alarm signal suppliedfrom connected device such as a camera or camera siteequipment. The recorder also generates an alarm signalitself when the preset motion detection activates. Any alarm signal starts alarm recording with the presetrecording mo...

29 ■ INTERNAL TIMER REC Reservations for recording are made in the INTERNALTIMER REC window on a weekly or daily basis. The TIMERindicator lights on the front panel after a reservation hasbeen made. OPERATE TIMER HDD ALARM SUSPEND DAYLIGHT SAVINGS FULL LOCK MEMORY CARD DISP LCD DISPLAY SELECT LCD CO...

30 ■ COMMUNICATION SETUP Communication parameters are set to match those of theconnected devices and the system configuration. ● Protocol 501 PROTOCOL 1. Move the cursor to PROTOCOL with the [ ▲ ] or [ ▼ ] but- ton. 2. Select a suitable protocol with the JogDial. The default is PS • DATA. PS • DATA:...

33 Password Verification Pause/Playback Skip Playback Backward Forward . . 32 Stop Recording (Capacity) Recording (Mode) Upward or downward When a button is pressed in KEY LOCK mode. To the right or left The center Alarm Recording Press the respective position on the LCD button to switch throughthe ...

34 DISPLAY SELECT STOP PLAY REC PUSH– PAUSE SET ALARM SEARCH STEP REW/FF PLAY MODE SELECT / / / / SETU/ESC LCD CONTRAST Digital Disk Recorder WJ-HD 2 1 ■ Recording ● Manual Recording Recording is possible at any time except during the setupoperation. The video supplied to the input terminal isrecord...

35 Alarm recording stops depending on the settings made inthe ALARM SETUP menu as follows: • If DURATION is selected, recording stops when the preset time has elapsed. • If MANUAL is selected, recording stops when the alarm input turns off. • If CONTINUE is selected, recording stops when the [ ■ STO...

36 DISPLAY SELECT LCD CONTRAST DISPLAY SELECT LCD CONTRAST NOV 27.00 23:27:00 TO SEARCH PUSH PLAY KEY DISPLAY SELECT STOP PLAY REC PUSH– PAUSE SET ALARM SEARCH STEP REW/FF PLAY MODE SELECT / / / / SETU/ESC LCD CONTRAST Digital Disk Recorder WJ-HD 1, 4 2 3 DISPLAY SELECT STOP PLAY REC PUSH– PAUSE SET...

37 T: Alarm terminal was activated. V: VMD was activated. Asterisk *: Corresponding alarm picture is recorded on the disk. No asterisk: Alarm was logged, but no picture was recorded. 4. Press the [ B PLAY] button to play it back. Note: Make certain to rotate the JogDial one click at a time. ● Alarm ...

38 ■ Alarm Operation ● Suspending Alarm Input Suspending the alarm function may be convenient during setup procedures or when alarm recording is not needed. In ONposition, any alarm input is ignored and the recorder performs as follows: • The alarm event will be logged in the alarm history.• The rec...

39 ● Resetting Alarm The activated alarm is reset by any of the inputs below. • The preset time has elapsed.• The [ ■ STOP] button on the front panel is pressed. • The alarm reset signal is supplied from the connected device. Resetting changes the status of the recorder as follows: • The recorder st...

40 “Finished !” appears on the LCD when copying ends. Replace with a new card when “Data Full” appears onthe LCD, then repeat step 6. 7. Pull the card out from the slot as follows. 7-1 Pull out the lever.7-2 Press the lever. DISPLAY SELECT LCD CONTRAST 5. Press the LCD button to the right or left to...

41 1. Enter your password with the JogDial while listening to the number of beeps because the password is hiddenon the LCD or monitor. The rules are as follows: • Each password has an invisible leading "0".• 2 beeps stand for "2" when turning the JogDial clock- wise. • 2 beeps stand ...

42 The pictures copied to theCompactFlash card are not the onesdisplayed on the monitor. Setup menus supplied from the MatrixSwitcher cannot be recorded. Contact your dealer for replacement of the fan. Connect the video monitor directly with the WJ-HD100. Phenomenon TROUBLESHOOTING The monitor recei...

43 SPECIFICATIONS General Required Power: 120 V AC 60 Hz Power Consumption: 24 W Operating Temperature: +5 °C to +45 °C (41 °F to 113 °F) Dimensions: 420 mm (W) x 44 mm (H) x 350 mm (D), excluding rubber feet16-9/16” x 1-3/4” x 13-13/16” Weight: 5.2 k g (2.4 lbs) Input Video Input: Composite video o...

Item SHIFT SETUP FUNCTION Step Playback REW. To Play/Stop SelectedAlarm Record To Show/Hide SETUPMENU The top of the oldest record will beaccessed. Jump to Oldest. UP L R UP DOWN R WV-CU360 44 APPENDIX ■ Remote Control From System Controller A system controller having PS • Data capability can contro...

45 DAYLIGHT SAVINGS OFF, INT or EXT selectable Operate LCD Button. Item WV-CU360 WJ-HD100 Note DAYLIGHT SAVINGS SHIFT SETUP FUNCTION 3 1 Timer REC ModeSelection SHIFT SETUP FUNCTION Button Lock OFF Operate LCD Button. Operate LCD Button. Button Lock ON SHIFT SETUP FUNCTION 3 1 SHIFT SETUP FUNCTION 3...

46 2. Escape from the prompt mode on the first unit.Press the STOP button on the unit you wish to begin recording. The FULL indicator on the unit will go off, indicating that theunit is operable, and the prompt mode is released. The other FULL indicators will remain on. This indicates that the other...

47 ■ Communication Protocol The following pages detail the elements for communication between the Digital Disk Recorder and the personal computer.Make certain to select VTR for PROTOCOL in the COMMUNICATION SETUP window. For BAUD RATE, DATA BIT and PARITYsettings, see page 30 COMMUNICATION SETUP. Fo...

48 ● Command Table Basic Operation Item Transmission Command (ASCII) Response (ASCII) Parameter (ASCII) Fast Forward to the end OFF OFF Pause OPA OPA Play OPL OPL Recording ORC ORC Rewind to the top ORW ORW Skip&Play Forward OSF:n OSF n = 0 to F 0 = Slowest F=Fastest Stop OSP:n OSP n = P stops P...

50 Inquiry Item Transmission Command (ASCII) Response (ASCII) Parameter (ASCII) Remaining Size QHR QHR:nnn nnn=000-100 Decimal % Inquiry ID Inquiry QID QID:WJ-HD100 Key Lock Status QKM QKM:n n=0 Lock OFF Inquiry n=1 Lock ON Alarm Info Inquiry QLD:n QLD:n (Alarm Information) In Transmission command: ...

● Reservation for Consecutive Days Reservations can be made for a consecutive recordingthrough a run of days. The Recorder continues recording ifan identical time is entered for either the END of the dayand the START of the next day. The reservation exampleshows a 3-day recording that begins at 18:0...

3 ● Réservation pendant des joursconsécutifs Des réservations peuvent être faites pour exécuter unenregistrement consécutif pendant plusieurs jours.L’enregistreur continue d’enregistrer si une durée identiqueest introduite pour les paramètres END et START.L'exemple de réservation indiqué illustre un...

NM0201-0 V8RA1274AN Printed in Japan N 19 Imprimé au Japon Panasonic Canada Inc. 5770 Ambler Drive, Mississauga,Ontario, L4W 2T3 Canada (905)624-5010 Panasonic Sales CompanyDivision of Matsushita Electric of Puerto Rico Inc. Ave. 65 de Infanteria. Km. 9.5San Gabriel Industrial Park, Carolina,Puerto ...

ADDENDUM The following changes and additions have been applied to the WJ-HD100 Operating Instructions. S Y S T E M I N F O R M A T I O N H D D H O U R M E T E R 1 0 0 0 H H D D C A P A C I T Y . G BD E F A U L T → S E T → V E R x . x x ( x . x x x . x x x . x x ) ● Folders & Files on page 40: De...

2 ● Communication Protocol, Operating Status Inquiry on page 50 has been corrected. Item Transmission Command (ASCII) Response (ASCII) Parameter (ASCII) Operating Status QOP xxx (Operating command) xxx=OPL Play Inquiry xxx=OPP Pause or Copy to card(addition)xxx=OPA Pause or Copy to card(deletion)xxx...

3 Additions to page 28 ● VMD description The recorder starts recording when video motion detection (VMD) is activated. The recording continues while VMD is active.The recording mode triggered by VMD continues at least for 30 seconds. Note: VMD recording is independent from the 304 DURATION setup, th...

4 <Thumbnail Mode Display> Click on the desired thumbnail to display it in zoomed sizeoverlaying the window.Selecting numbers in SKIP and ID columns can also dis-play a zoomed picture only if the copied pictures arederived from a Video Multiplexer. SKIP: Enter the total number of cameras conne...

5 3. Specify the start time with the JogDial, LCD button, ↑ and ↓ button. • To increase or decrease the parameter, rotate the JogDial clockwise or counter-clockwise. Pressing the LCD button upward or downward will perform the same operation. • To move the cursor to the right or left, press the LCD b...