Panasonic PT-DS8500U - Manuals
Panasonic PT-DS8500U – Manual in PDF format online.
Manuals:
Manual Panasonic PT-DS8500U
Summary
Important Safety Notice 2 - ENGLISH Important Information Important Safety Notice Dear Panasonic Customer: The following information should be read and understood as it provides details, which will enable you to operate the projector in a manner which is both safe to you and your environment, and co...
Important Safety Notice ENGLISH - 3 Important Information WARNING: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a resid...
4 - ENGLISH Important Information Preparation Getting Started Basic Operation Settings Maintenance Appendix The size is almost the same as the former model but the luminance is about 1.5 times higher. 7 000 lm : PT-D7700U (two lamps LAMP POWER : [HIGH]) 10 600 lm : PT-DZ8700U (two lamps LAMP POWER :...
ENGLISH - 5 Important Information Preparation Getting Started Basic Operation Settings Maintenance Appendix Contents Be sure to read “Precautions with regard to safety”. ( pages 8 to 16) Important Information Important Safety Notice ............................ 2Precautions with regard to safety ......
8 - ENGLISH Important Information Precautions with regard to safety WARNING POWER The wall outlet or the circuit breaker shall be installed near the equipment and shall be easily accessible when problems occur. If the following problems occur, cut off the power supply immediately. Continued use of...
Precautions with regard to safety ENGLISH - 9 Important Information Do not place another projector or other heavy objects on top of the projector. Failure to observe this will cause the projector to become unbalanced and fall, which could result in damage or injury. The projector will be damaged or ...
Precautions with regard to safety 10 - ENGLISH Important Information Do not allow children to reach the AA/R6 batteries. The battery can cause personal injury if swallowed. z If swallowed, seek medical advice immediately. z If the battery fluid leaks, do not touch it with bare hands, and take the fo...
Precautions with regard to safety ENGLISH - 11 Important Information CAUTION POWER When disconnecting the power cord, be sure to hold the power plug and power connector. If the power cord itself is pulled, the lead will become damaged, and fire, short-circuits or serious electric shocks will resul...
Precautions with regard to safety 12 - ENGLISH Important Information Cautions when installing After removing the projection lens, install the dust sponge attached to the projector. If the dust sponge is not installed, dust will be accumulated inside and can cause a trouble. Do not use under the fo...
Precautions with regard to safety ENGLISH - 13 Important Information Cautions when setting the projectors 1 When installing and using the projector with a method other than floor standing installing using adjustable z feet, fix it with the 5 ceiling mounting screws (shown in the figure). (Screw di...
Precautions with regard to safety 14 - ENGLISH Important Information Cautions when setting the projectors 2 When placing the projector in confined space, a ventilation or air conditioning system must be equipped, and z keep enough ventilation space on the rear and both sides of the projector. Make...
Precautions with regard to safety ENGLISH - 15 Important Information Do not touch the surface of the projector lens with your bare hand. If the surface of the lens becomes dirty from fingerprints or anything else, this will be magnified and projected onto the screen. Please put the lens cover on t...
Precautions with regard to safety 16 - ENGLISH Important Information Accessories Make sure the following accessories are provided with your projector. Remote control (x1) (N2QAYB000550) Power cord (x1) (TXFSX01RGQZ) Drop-prevention bracket (x2) (TTRA0238) Safety cables (x2) Washers (x4) Wire rope fi...
ENGLISH - 17 Preparation About Your Projector Attention Do not drop the remote control. z Avoid contact with liquids or moisture. z Do not attempt to modify or disassemble the remote control. z Do not let strong light shine onto the signal receptor. The remote control may malfunction under strong li...
About Your Projector 18 - ENGLISH Preparation Projector body J Front view Side views J Û : Attach a commercial burglar prevention cable. Burglar hook port Û Auto Cleaning Filter (ACF) compartment ( Æ page 109) Remote control signal receptor Air exhaust port Air intake port Air intake port Air intake...
About Your Projector ENGLISH - 19 Preparation J CONTROL PANEL J Terminals on side Attention Do not touch the LAN terminal with your bare hands or body, as body parts may have charged static electricity. Failure to z do so may cause malfunctions. Do not touch the metallic parts of LAN terminal and ca...
About Your Projector 20 - ENGLISH Preparation Setting projector ID number to remote control Each projector can be assigned a unique ID number, and the handheld remote’ s number must be set to match the intended projector. The ID number of the projector is set to “ALL” on shipping, and use the ID ALL...
ENGLISH - 21 Getting Started Setting up Projection method You can use the projector with any of the following 4 projection methods. To set the desired method in the projector. J Mounting on the ceiling and projecting from front J Setting on a desk/floor and projecting from rear (Using translucent sc...
Setting up 22 - ENGLISH Getting Started Screen size and throw distance When planning the projector and screen geometry, refer to the figures below and the information on the following pages for reference. After the projector is roughly positioned, picture size and vertical picture positioning can be...
Setting up ENGLISH - 23 Getting Started J Projected range using geometric adjustment (PT-DZ8700U/PT-DS8500U only) VERTICAL KEYSTONE (Side View) HORIZONTAL KEYSTONE (Top View) VERTICAL ARC (Side View) HORIZONTAL ARC (Top View) Lens Keystone correction only When using arc and keystone correction toget...
Setting up ENGLISH - 31 Getting Started If the projector is used with a screen size not listed in this manual, check the diagonal dimension (inch) of your screen and calculate the projection distance using the following formulas. J Calculation formulas for projection distance by lens types (for PT-D...
Setting up ENGLISH - 33 Getting Started J Calculation formulas for projection distance by lens types (for PT-DW8300U) Model number of projection lens Throw ratio Aspect ratio Projection distance (L) formula Unit : m Zoom lens ET-D75LE1 1.5–2.0 : 1 16 : 9 Min. : L = 0.0343 × SD (") - 0.0760 Max. ...
34 - ENGLISH Getting Started Connections Before connection to the projector Read carefully the instruction manual for the device to be connected. z Turning off the power switch of the devices before connecting cables. z If any connection cable is not supplied with the device, or if no optional cable...
Connections ENGLISH - 35 Getting Started J Pin assignments and signal names of <DVI-D IN> terminal Outside view Pin No. Signal names Pin No. Signal names T.M.D.S data 2- — T.M.D.S data 2+ +5V T.M.D.S data 2/4 shield GND — Hot plug detection — T.M.D.S data 0- DDC clock T.M.D.S data 0+ DDC data ...
Connections 36 - ENGLISH Getting Started Connecting example : Computers Note The DVI-D signal input terminal supports only a single link. z For the specifications of the RGB signals that can be applied from the PC, refer to “List of compatible signals”. z ( Æ page 122) If your computer has the resum...
ENGLISH - 37 Getting Started Removing/attaching the projection lens (optional) Move the lens to the home position before replacing or removing the projection lens. ( Æ page 43) How to install the projection lens Align the mark (orange) on the 1 ) projection lens with the mark on the projector ( on t...
38 - ENGLISH Basic Operation Powering ON/OFF Connecting the power cord Be sure to Insert the attached power cord securely to its base to prevent it from coming off. Before connecting the power cord, confirm that the MAIN POWER switch is in the “ ” (OFF) position. J Installation Insert the plug secur...
Powering ON/OFF ENGLISH - 39 Basic Operation Powering up the projector When using an optional lens, install a projection lens before switch on the projector. ( Æ page 37) Remove the projection lens cover from the lens. Connect the supplied power cable. 1 ) (AC120 V 60 Hz) Press the [ | ] marked side...
Powering ON/OFF 40 - ENGLISH Basic Operation Powering off the projector Press POWER STANDBY ( 1 ) ). Press ◄► to select [OK] and press 2 ) (ENTER). (or press POWER STANDBY ( ) again.) The projection of the image stops, and [Power indicator] lamp of the main unit lights up orange. (The cooling fan ke...
ENGLISH - 41 Basic Operation Projecting Check the connections of the peripheral devices, installation of the projection lens ( Æ page 37), and connection of the power cord ( Æ page 38) and switch on the power ( Æ page 39) to start the projector. Select the input signal and adjust the image. Selectin...
Projecting 42 - ENGLISH Basic Operation Adjustment range after lens position (optical shift) Do not move the lens beyond the bounds of the shift range as this may cause a change in the focus. This limitation is to protect the parts of the projector. Using the standard projection position as the refe...
Projecting ENGLISH - 43 Basic Operation Moving the projection lens position to the home position Press and hold <LENS> button on the projector’s controls or <SHIFT> button on the 1 ) remote control for 3 seconds or more. Press <ENTER> button while the menu shown above is being disp...
Projecting 44 - ENGLISH Basic Operation J Procedure for adjusting the focus balance (tilt compensation in the lens mount) Three focus adjustment screws on the lens mount may be used to compensate for uneven screen focus. Structure of lens mount Q The three adjustment screws allow the lens to be tilt...
Projecting ENGLISH - 45 Basic Operation If the lens is heavy or the projector is installed so that it is tilted, the lens may be tilted, resulting in the focus becoming unbalanced. In such a case, refer to the figure 3 and table below, and follow the procedure below to perform adjustment. Adjustment...
46 - ENGLISH Basic Operation Basic operations using the remote control Using the SHUTTER function If the projector is not used for a certain period of time during the meeting intermission, for example, a shutter mode is available that allows the user to hide images temporarily. button Press <SHUT...
Basic operations using the remote control ENGLISH - 47 Basic Operation Automatic adjustment The automatic setup function can be used to automatically adjust the resolution, clock phase and picture position when analog RGB signals consisting of bitmap images such as computer signals are being input, ...
Basic operations using the remote control 48 - ENGLISH Basic Operation Changing the picture aspect ratio You can toggle through an appropriate set of aspect ratios for a given input signal. button Press <ASPECT> button on the remote control. The setting will change as follows each time z <A...
ENGLISH - 49 Settings Menu Navigation Menus are extensively used for configuring, adjusting or reconfiguring the projector. Navigating through the menu J Operating procedure Press <MENU> button. 1 ) [MAIN MENU] appears on the screen. Press ▲▼ to select the desired item. 2 ) The selected item i...
52 - ENGLISH Settings PICTURE menu See “Navigating through the menu” z ( Æ page 49). See “MAIN MENU” and “SUB MENU” z ( Æ page 50). PICTURE MODE The user can switch to the desired picture mode suitable for the image source and the environment in which this projector is used. Press ▲▼ to select [PICT...
PICTURE menu ENGLISH - 53 Settings CONTRAST You can adjust the contrast of the projected image. Press ▲▼ to select [CONTRAST]. 1 ) Press ◄► or <ENTER> button. 2 ) The [CONTRAST] individual adjustment screen z will be displayed. Press ◄► to adjust the level. 3 ) Operation Adjustment Adjustment ...
PICTURE menu 54 - ENGLISH Settings COLOR TEMPERATURE You can adjust the white balance of the projected image. Press ▲▼ to select [COLOR 1 ) TEMPERATURE].Press ◄► or <ENTER> button. 2 ) The [COLOR TEMPERATURE] individual z adjustment screen will be displayed. Press ◄► to switch [COLOR 3 ) TEMPE...
PICTURE menu ENGLISH - 55 Settings Press ▲▼◄► to select characters 5 ) and press <ENTER> button to input them.Press ▲▼◄► to select [OK], and 6. press <ENTER> button. The color temperature setting name is changed. z GAMMA This switches the gamma mode. Press ▲▼ to select [GAMMA]. 1 ) Press...
PICTURE menu 56 - ENGLISH Settings SHARPNESS This adjusts the sharpness of the pictures. Press ▲▼ to select [SHARPNESS]. 1 ) Press ◄► or <ENTER> button. 2 ) The [SHARPNESS] individual adjustment z screen will be displayed. Press ◄► to adjust the level. 3 ) Operation Adjustment Adjustment range...
PICTURE menu ENGLISH - 57 Settings SYSTEM SELECTOR This enables the projector to automatically recognize input signals. Furthermore, if unstable signals are input, the system format can be selected manually. Press ▲▼ to select [SYSTEM 1 ) SELECTOR].Press <ENTER> button. 2 ) Press ▲▼ to switch ...
58 - ENGLISH Settings POSITION menu See “Navigating through the menu” z ( Æ page 49). See “MAIN MENU” and “SUB MENU” z ( Æ page 50). SHIFT This function allows the user to adjust the raster position vertically or horizontally if the position of the image projected on the screen is displaced even whe...
POSITION menu ENGLISH - 59 Settings VID AUTO (PRI.) J The projector identifies the abovementioned VID or S1 signals and displays the picture by automatically choosing the screen sizes of 4 : 3 or 16 : 9 according to the VID if it is detected or S1 signals if a VID is not detected. This function is e...
POSITION menu 60 - ENGLISH Settings Press ▲▼ to select [INTERLOCKED]. 3 ) Press ◄► to switch [INTERLOCKED]. 4 ) OFF The [VERTICAL] and [HORIZONTAL] settings are used as the vertical and horizontal zoom ratios respectively. ON The zoom ratio is set to the [BOTH] setting. This allows the pictures to b...
POSITION menu ENGLISH - 61 Settings KEYSTONE menu J VERTICAL KEYSTONE z VERTICAL SUB KEYSTONE z HORIZONTAL KEYSTONE z HORIZONTAL SUB KEYSTONE z LINEARITY z J CURVED menu LENS THROW RATIO z Set to the throw ratio being used (the projection distance divided by the screen width).VERTICAL KEYSTONE z HOR...
POSITION menu 62 - ENGLISH Settings KEYSTONE (PT-DW8300 only) If the projector is aligned non-perpendicularly to the screen, or if the projection screen has an angled surface, you can correct keystone. Press ▲▼ to select [KEYSTONE]. 1 ) Press <ENTER> button. 2 ) Select the desired adjustment i...
ENGLISH - 63 Settings ADVANCED MENU See “Navigating through the menu” z ( Æ page 49). See “MAIN MENU” and “SUB MENU” z ( Æ page 50). DIGITAL CINEMA REALITY Increase the vertical resolution when the PAL (or SECAM) 576i signal input or the NTSC 480i, 1 080/50i and 1 080/60i signal input is applied. Pr...
ADVANCED MENU 64 - ENGLISH Settings INPUT RESOLUTION Input resolution adjustment achieves the best image when the screen flickers or halo is observed around the contour. Set the values appropriately for the signal resolution that is being used. Press ▲▼ to select [INPUT 1 ) RESOLUTION].Press <ENT...
ADVANCED MENU ENGLISH - 65 Settings J To display the adjustment marker Press ▲▼ to select [MARKER]. 7 ) Press ◄► to select [ON]. 8 ) A marker for adjusting the overlap position z appears. The optimal point is the position where the red line of one frame overlaps the green line of the other frame. Th...
ADVANCED MENU 66 - ENGLISH Settings FRAME DELAY When 1 080/60i, 1 080/50i and 1 080/24sF signals are being input, this simplifies image processing so that the video frame delay is shortened. Press ▲▼ to select [FRAME DELAY]. 1 ) Press ◄► to switch [FRAME DELAY]. 2 ) The setting will change as follow...
ENGLISH - 67 Settings DISPLAY LANGUAGE menu See “Navigating through the menu” z ( Æ page 49). See “MAIN MENU” and “SUB MENU” z ( Æ page 50). Changing the display language This lets you switch the on-screen display language. Menus, setting items, adjustment screens, and z control button names will be...
68 - ENGLISH Settings See “Navigating through the menu” z ( Æ page 49). See “MAIN MENU” and “SUB MENU” z ( Æ page 50). COLOR MATCHING When multiple sets are used simultaneously, this projector allows the user to correct the difference of colors among the sets. Press ▲▼ to select [COLOR 1 ) MATCHING]...
DISPLAY OPTION menu ENGLISH - 69 Settings Press <ENTER> button. 3 ) The [ z 709MODE ] or [ MEASURED MODE ] screen will be displayed. Press ▲▼ to select [MEASURED 4 ) DATA].Press <ENTER> button. 5 ) The [MEASURED DATA] screen will be z displayed. Use the colorimeter to measure 6 ) the lum...
DISPLAY OPTION menu 70 - ENGLISH Settings Press ◄► to adjust [SCREEN 4 ) POSITION]. In the case of the PT-DZ8700U : z When [SCREEN FORMAT] is [16 : 9] Adjustment range: -60 to +60 When [SCREEN FORMAT] is [4 : 3] Adjustment range: -160 to +160 In the case of the PT-DS8500U, you can adjust z the setti...
DISPLAY OPTION menu ENGLISH - 71 Settings Adjust the light portion of RED. 4 ) In [RED] of [WHITE BALANCE HIGH], adjust z the 100 % of the white level of the image signal to the position corresponding to 100 % on the waveform monitor. ( Æ page 54) Adjust [GREEN] and [BLUE] in a 5 ) similar manner. N...
DISPLAY OPTION menu 72 - ENGLISH Settings J Adjusting the position automatically Select [POSITION ADJUST] in step 3). 1. Press ◄► to switch [POSITION 2. ADJUST]. The setting will change as follows each time z ◄► is pressed. OFF ON OFF Automatic adjustment is off. ON Screen position and size are adju...
DISPLAY OPTION menu ENGLISH - 73 Settings Press ◄► to switch [DVI SIGNAL 6 ) LEVEL]. The setting will change as follows each time z ◄► is pressed. 0-255 : PC 16-235 0-255 : PC Select this when, for example, an external device (PC, etc.) is connected via the DVI terminal output. 16-235 Select this wh...
DISPLAY OPTION menu 74 - ENGLISH Settings J OSD DESIGN This sets the color of the on-screen display (OSD). 1 : Yellow 2 : Blue 6 : Brown 3 : White 5 : Pink 4 : Green J OSD MEMORY The current menu cursor position will be retained temporarily unless the projector switched off. ON OFF J INPUT GUIDE Thi...
ENGLISH - 75 Settings PROJECTOR SETUP menu See “Navigating through the menu” z ( Æ page 49). See “MAIN MENU” and “SUB MENU” z ( Æ page 50). PROJECTOR ID The projector has an ID number setting function that helps the user to control two or more projectors either simultaneously or separately with a si...
PROJECTOR SETUP menu 76 - ENGLISH Settings COOLING CONDITION You can control the fan speed for projecting angle. When the projector is angled, [COOLING CONDITION] setting must be set correctly. Failure to observe this may result in malfunctions, or the life of the lamp or the other components may be...
PROJECTOR SETUP menu ENGLISH - 77 Settings Note Only when [DUAL] or [SINGLE] is selected in [LAMP z SELECT], [LAMP RELAY] is available If [DUAL] is selected in [LAMP SELECT], only one lamp z is turned on for four hours after the set time. The setting time will be the local time. z ( Æ page 84) The t...
PROJECTOR SETUP menu 78 - ENGLISH Settings When [MODE] is set to [AUTO] Q Press ▲▼ to select [LINK]. 5 ) Press ◄► to switch [LINK]. 6 ) The setting will change as follows each time z ◄► is pressed. OFF GROUP A GROUP D GROUP C GROUP B OFF Brightness is corrected using the brightness sensor of one of ...
PROJECTOR SETUP menu 80 - ENGLISH Settings Details of error z Error message Remedial measure [Exceed maximum number of projectors.] Limit number of • projectors in same group to 8. When linking 9 or • more projectors, use a computer and the [Multi Projector Monitoring & Control Software]. [Pleas...
PROJECTOR SETUP menu ENGLISH - 81 Settings Display the internal test pattern [ALL 9 ) WHITE] on all projectors.Set [BRIGHTNESS CONTROL GAIN] 10) of all projectors to 100 %.Set [BRIGHTNESS CONTROL GAIN] 11) of the darkest projector to 90 %.Adjust [BRIGHTNESS CONTROL 12) GAIN] of the other projectors ...
PROJECTOR SETUP menu 84 - ENGLISH Settings NO SIGNAL SHUT-OFF You can set the timer to switch off the power of the projector after a certain period of time automatically when no signal is detected. Press ▲▼ to select [NO SIGNAL 1 ) SHUT-OFF].Press ◄► to switch [NO SIGNAL 2 ) SHUT-OFF]. DISABLE Deact...
PROJECTOR SETUP menu ENGLISH - 85 Settings Press <ENTER> button. 4 ) The [ADJUST CLOCK] screen will be displayed. z Press ▲▼ to select the item to be set, 5 ) and press ◄► to set the local time.Press ▲▼ to select [APPLY], and 6 ) press <ENTER> button. This completes setting of the time. ...
PROJECTOR SETUP menu 86 - ENGLISH Settings SAVE ALL USER DATA This saves various setting values as a backup to the internal memory of the projector. Press ▲▼ to select [SAVE ALL USER 1 ) DATA].Press <ENTER> button. 2 ) The [SECURITY PASSWORD] screen will be z displayed. Enter the password set ...
ENGLISH - 87 Settings P IN P menu See “Navigating through the menu” z ( Æ page 49). See “MAIN MENU” and “SUB MENU” z ( Æ page 50). Using the P IN P function Two videos can be projected simultaneously by placing a separate small sub screen within the main screen. Press ▲▼ to select [P IN P]. 1 ) Pres...
88 - ENGLISH Settings TEST PATTERN menu See “Navigating through the menu” z ( Æ page 49). See “MAIN MENU” and “SUB MENU” z ( Æ page 50). TEST PATTERN Results of adjustment of the position, size and other factors are not reflected in test patterns. Ensure the input signal is displayed before performi...
ENGLISH - 89 Settings See “Navigating through the menu” z ( Æ page 49). See “MAIN MENU” and “SUB MENU” z ( Æ page 50). J REGISTERED SIGNAL STATUS The name can be set for each sub memory. z MEMORY NO. : A1 (1-2) z Registering a signal to the list When a new format input signal is applied to the proje...
TEST PATTERN menu 90 - ENGLISH Settings Managing the sub memory list You can restore the sub memory data when using signals from the same input source. Sub memory data contains the setting information of screen and image adjustments, such as BRIGHTNESS, CONTRAST or ASPECT. J Registering the current ...
ENGLISH - 91 Settings SECURITY menu See “Navigating through the menu” z ( Æ page 49). See “MAIN MENU” and “SUB MENU” z ( Æ page 50). When you apply to the [SECURITY] menu z before you change the password to your original, perform to input the following factory default password operation. Press ▲►▼◄▲...
SECURITY menu 92 - ENGLISH Settings DISPLAY SETTING You can set your original text, such as company name or URL information, to display regularly on the projected image while projecting. Press ▲▼ to select [DISPLAY 1 ) SETTING].Press ◄► to switch [DISPLAY 2 ) SETTING]. The setting will change as fol...
SECURITY menu ENGLISH - 93 Settings CONTROL DEVICE SETUP Control from the remote control and main unit controls can be restricted. Press ▲▼ to select [CONTROL 1 ) DEVICE SETUP].Press <ENTER> button. 2 ) The [CONTROL DEVICE SETUP] screen will z be displayed. Press ▲▼ to select [CONTROL 3 ) PANE...
94 - ENGLISH Settings NETWORK menu See “Navigating through the menu” z ( Æ page 49). See “MAIN MENU” and “SUB MENU” z ( Æ page 50). NETWORK SETUP Make the initial network settings before using the network connection. Press ▲▼ to select [NETWORK 1 ) SETUP].Press <ENTER> button. 2 ) The [NETWORK...
NETWORK menu ENGLISH - 95 Settings Network connections The projector is equipped with network functions, and web browser controls can be used to carry out the following operations from a computer. Projector settings and adjustments z Projector status display z Transmission of E-mail messages if ther...
NETWORK menu 96 - ENGLISH Settings Accessing from the Web browser Activate the Web browser in the personal computer. 1 ) Enter the IP address set by the projector into the URL input field of the Web browser. 2 ) Enter your “User name” and “Password”. 3 ) The factory default settings are user1 (user ...
NETWORK menu ENGLISH - 97 Settings Change Password page J Click [Change password]. Administrator User Administrator mode Q Administrator account z Account Current user name input field Current password input field New user name input field New password input field New password input field (re-enter ...
NETWORK menu 98 - ENGLISH Settings Basic control page J To move from another page, click [Projector control], then [Basic control]. Page selection tabs Click these to switch pages. This displays the on-screen status. It is displayed even if the on-screen display of the projector is set to off. Monit...
NETWORK menu ENGLISH - 99 Settings Detail control page J Click [Projector control], then [Detail control] to display the Detail control page. Pressing these buttons controls the projector and updates the on-screen description on the right of the control page when control is finished. Lens adjustment...
NETWORK menu 100 - ENGLISH Settings Error information page J When “Error (Detail)” is displayed on the status information screen, click it to display the error details. Depending on the nature of the error, the projector may be placed in the standby mode for its own z protection. When [FAILED] has a...
NETWORK menu 104 - ENGLISH Settings Authentication set up page J The POP/SMTP server is set on this page when POP/SMTP authentication is required for mail transmissions. Click [Detailed set up], then [Authentication set up] to display the Authentication server setup page. Select the authentication m...
NETWORK menu ENGLISH - 105 Settings Contents of mail sent J Mail with the contents shown below is sent when the E-mail settings have been Q established. ࣹࣹࣹࣜऌझपझयफपथटࣜबमफदडटरफमࣜमडबफमरࣤࣿऋऊंअःऑऎँࣹࣹࣹࣥࣜऌमफदडटरफमࣜऐवबडࣶࣜࣜࣜࣜࣜࣜࣜࣜࣜࣜࣜऀखࣦࣦࣦࣦएडमथझनࣜऊफࣶࣜࣜࣜࣜࣜࣜࣜࣜࣜࣜࣜࣜࣜࣜࣜࣜएओࣰࣱࣲ࣭࣮࣯ࣳ ࣩࣩࣩࣩࣩࣜࣜँࣩऩझथनࣜयडरऱबࣜठझरझࣩࣩࣩࣩࣩࣜऐँउऌ...
NETWORK menu 106 - ENGLISH Settings J Adjust clock page Click [Detailed set up], then [Adjust clock] to display the Adjust clock page. Time zone selection Button to update time zone setting Turn this [ON] to set the date and time automatically. When setting the date and time automatically, input the...
ENGLISH - 107 Maintenance Monitor Lamp indicators Managing the indicated problems If a problem should occur with the projector, the indicators will inform you. Manage the indicated problems as follow. Attention J LAMP1/LAMP2 indicator Lamp indication Information Check point Remedial measure Lighting...
Monitor Lamp indicators 108 - ENGLISH Maintenance J TEMP indicator Lamp indication Information Check point Remedial measure Lighting in red Warm-up status Did you turn on the power when z the ambient temperature was lower than approx. 0 °C (32 °F)? Wait about 5 minutes in the current z status. Insta...
ENGLISH - 109 Maintenance Replacement Before replacing the unit Turn off the POWER switch of the projector in proper way and disconnect the power plug from the wall outlet. z ( Æ pages 38, 40) Be sure to observe the procedure “Powering off the projector” z ( Æ page 40) when performing power supply o...
Replacement 110 - ENGLISH Maintenance J Lamp unit The LAMP unit is consumable product. You can check the duration of usage time using [LAMP1/LAMP2] of [STATUS] ( Æ page 83) in the [PROJECTOR SETUP] menu. Replacement of the lamp unit should be carried out by a qualified technician. Contact the dealer...
Replacement ENGLISH - 111 Maintenance J Procedure of lamp unit replacement Attention When the projector is mounted in the ceiling, do not work directly under the projector or put your face close to the projector. z The lamp unit and the lamp unit cover must be attached correctly and securely. Failur...
112 - ENGLISH Maintenance Troubleshooting Should any problem persist, contact your dealer. Problem Cause Reference page Power does not turn on. The power cord may not be connected. z — The <MAIN POWER> switch is turned off. z 40 No electric supply is at the wall outlet. z — The circuit breaker...
114 - ENGLISH Appendix Technical Information PJLink protocol The network function of the projector supports PJLink class 1, and the PJLink protocol can be used to perform projector setting and projector status query operations from a computer. J Control commands The following table lists the PJLink ...
Technical Information ENGLISH - 115 Appendix Control commands via LAN J When WEB Control administrator rights password is set (Protect mode) <Connection method> Obtain the IP address and port number (Initial set value = 1024) of the projector and 1 ) make a request for connection to the projec...
Technical Information 116 - ENGLISH Appendix J When WEB Control administrator rights password is not set (Non-protect mode) <Connection method> Obtain the IP address and port number (Initial set value = 1024) of the projector and 1 ) make a request for connection to the projector. You can obta...
Technical Information ENGLISH - 117 Appendix Serial terminal The serial connector which is on the connector panel of the projector conforms to the RS-232C interface specification, so that the projector can be controlled by a personal computer which is connected to this connector. J Connection J Pin ...
Technical Information 118 - ENGLISH Appendix J Basic format Transmission from the computer begins with STX, then the ID, command, parameter, and ETX are sent in this order. Add parameters according to the details of control. STX A D I 1 I 2 ; C1 C2 C3 : P1 P2 Pn ETX When sending commands without par...
Technical Information ENGLISH - 119 Appendix J Cable specifications <When connected to a computer> Projector 1 NC NC 1 Computer (DTE specifications) 2 2 3 3 4 NC NC 4 5 5 6 NC NC 6 7 7 8 8 9 NC NC 9 J Control commands When controlling the projector from a computer, the following commands are a...
Technical Information 120 - ENGLISH Appendix REMOTE 2 IN terminal Using the [REMOTE 2 IN] terminal provided on the connection terminals of the main unit, it is possible to operate the projector from a control panel etc. furnished in a distant location where infrared remote control signal cannot be r...
Technical Information ENGLISH - 121 Appendix Two window display combination list Subwindow Main window RGB1 RGB2 VIDEO input S- VIDEO input DVI HDMI *3 SDI RGB input YP B P R input RGB input YP B P R input *1 Moving image system *2 RGB system *1 Moving image system *2 RGB system RGB1 RGB input YP B ...
Technical Information 122 - ENGLISH Appendix List of compatible signals The following table specifies the types of signals compatible with the projector. Format : V = VIDEO, S = S-VIDEO, D = DVI, H : HDMI, R : RGB, Y : YP B P R , SDI Û Mode Display resolution (dots) Scanning frequency Dot clock freq...
124 - ENGLISH Appendix Specifications Model No. PT-DZ8700U PT-DS8500U PT-DW8300U Power supply AC120 V 60 Hz Power consumption 970 W 950 W When [STANDBY MODE] is [ECO] : Approx. 0.2 W When [STANDBY MODE] is [NORMAL] : Approx. 6 W Amps 9.5 A 9.0 A DLP chip Panel size 0.96 inch (aspect ratio 16 : 10) 0...
Ceiling mount bracket safeguards ENGLISH - 127 Appendix Ceiling mount bracket safeguards When installing the ceiling mount bracket to the projector, install the accessory Drop-prevention bracket (Safety cables) to the projector. (The projector will still be safe if they are not used, however they wi...
Index 128 - ENGLISH Appendix Index A About brand ..................................126 Accessories ....................................16 ADVANCED MENU ........................63 ASPECT .........................................58 AUTO SETUP .................................71 AUTO SETUP function ......
F0710-10710 TQBJ0341 Panasonic Solutions Company 3 Panasonic Way, Secaucus, NJ 07094 TEL: (877) 803 - 8492 Panasonic Canada Inc. 5770 Ambler Drive, Mississauga, Ontario L4W 2T3 TEL: (905) 624 - 5010 ヱㄏㄔㄐㄏㄊチヤㄐㄓㄑㄐㄓㄕㄊㄐㄏ Web Site : http://panasonic.net/avc/projector/ © Panasonic Corporation 2010 NOT...
Panasonic Manuals
-
Panasonic RB F10
User Manual
-
Panasonic SC HTB200
User Manual
-
Panasonic CS Z25UFRAW CU Z25UBRA
Manual
-
Panasonic CS Z25UFRAW CU Z25UBRA
Installation Manual
-
Panasonic CS Z50UFRAW CU Z50UBRA
User Manual
-
Panasonic DMW BLK22
User Manual
-
Panasonic DMW BLK22
Manual
-
Panasonic NI WL55
Manual
-
Panasonic DMP BD903
Manual
-
Panasonic DMP BD903
User Manual
-
Panasonic DMP BD903
Installation Manual
-
Panasonic NN ST23QM
Manual
-
Panasonic FV-1115VK3
User Manual
-
Panasonic EH NA0J
Manual
-
Panasonic FV 30BG3
Manual
-
Panasonic RE7 59
User Manual
-
Panasonic NE C1275
Manual
-
Panasonic RG T810LHA
User Manual
-
Panasonic CF SR
User Manual
-
Panasonic RZ B110W
User Manual