Panasonic kx-tgp500 - Manuals

In cases when buttons/soft key icons are shown in symbols/pictures1. Base unit: (middle soft key) ® [#][5][0][0] Handset: (center of joystick) ® [#][5][0][0] 2. [ ]/[ ]: Select " On " for DHCP ® 3. [ ]/[ ]: Select " Automatic " for DNS ® • Select " Manual " to enter the addre...

For details about the settings that can be configured with the configuration files and how to specify the settings,see Section 4 Configuration File Programming . Preset Factory defaults Factory Factory defaults Pre-provisioning Phone system dealer Pre-provisioning data Pre-provisioning can aid the i...

1.1.5.3 Server for Pre-provisioning The DHCP server and TFTP server play important roles in performing pre-provisioning. This section explainstheir purposes, uses, and brief descriptions. Server Purpose Description DHCP server Used to provide the addressof a TFTP server, set in option66 of the DHCP ...

Prior Settings Item Description/Setting DHCP server option 66 192.168.0.130 IP address range assigned by DHCP server 192.168.0.16 to 192.168.0.63 File name of the configuration file used forpre-provisioning KX-TGP500B01.cfg URL of the configuration file used forprovisioning that is entered in the co...

1.1.6 Provisioning 1.1.6.1 What is Provisioning? After pre-provisioning has been performed ( ® see 1.1.5 Pre-provisioning ), you can set up the unit automatically by downloading the configuration file stored on the provisioning server into the unit. This iscalled "provisioning". Pre-provisio...

Type Usage Master configuration file Configure settings that are common to all units, such as the SIPserver address, and the IP addresses of the DNS and NTP (NetworkTime Protocol) servers managed by your phone system dealer. Thisconfiguration file is used by all the units. Example of the configurati...

Download Timing Explanation None (prohibited) If you want to prohibit units from changing their settings by downloadingconfiguration files, you can enable this function from the Web user interface.The following operations will be prohibited: – Pre-provisioning – Provisioning at startup – Provisionin...

http://prov.example.com/Panasonic/Config0080F0111111.cfg b. The unit with the MAC address 0080F0222222 accesses the following URLs:http://prov.example.com/Panasonic/ConfigCommon.cfghttp://prov.example.com/Panasonic/Config0080F0222222.cfg Example Provisioning Direction from the Server The following f...

To decrypt configuration files, the unit uses the encryption key registered to it beforehand. The unit determinesthe encryption status by checking the extension of the downloaded configuration file.For details about encrypting configuration files, contact the appropriate person in your organization....

1.1.7 Web User Interface Programming After connecting the unit to your network, you can configure the unit’s settings by accessing the Web userinterface from a PC connected to the same network. For details, see Section 3 Web User Interface Programming . Router Switching Hub KX-TGP500 KX-TGP550 PC 1....

1.1.8 Phone User Interface Programming You can change the settings directly from the unit.For details about the operations, refer to the User Guide on the Panasonic Web site ( ® see Introduction ). For details about additional features available with direct commands, see Section 2 Phone User Interfa...

1.1.10.2 NAT (Network Address Translation) Setup This section provides information about configuring a router that uses NAT. Router PC Private IP address: 192.168.228.11 SIP Cordless Phone Private IP address: 192.168.228.12 Switching Hub Global IP address:xxx.yyy.zzz.127 Internet If the unit is conn...

To set the router’s external (global) IP address and reception port number in the unit1. In the Web user interface, click the [Network] tab, click [Static NAPT Settings] , and then enter the router’s global IP address in [Global IP Address] . 2. Select [Yes] for [Enable Global IP Address Usage per L...

NATs) or SIP messages, to perform this feature. For details about specifying this setting through the Web userinterface, see 3.4.4 Global Address Detection . To set Global Address Detection1. In the Web user interface, click the [Network] tab, click [Global Address Detection] , and then select [STUN...

2.1 Phone User Interface Programming This section provides information about the features that can be configured directly from the base unit orhandsets, but that are not mentioned in the User Guide.To enter direct commands, use the keys and soft keys on the base unit (KX-TGP550 only) or handset.For ...

To set the link speed and duplex mode In cases when buttons/soft key icons are shown in English alphabet1. Base unit: [MENU] (middle soft key) ® [#][5][3][0] Handset: [MENU] (center of joystick) ® [#][5][3][0] • For KX-TGP500 users: go to step 4 . 2. [ ]/[ ]: Select " Speed/Duplex " ® [SELEC...

3. [ ]/[ ]: Select " Enable VLAN " ® 4. [ ]/[ ]: Select " Yes " ® • Select " No " to disable VLAN settings. 5. Base unit: [ ] Handset: [ ] To set VLAN for IP Phone/PC In cases when buttons/soft key icons are shown in English alphabet1. Base unit: [MENU] (middle soft key) ® [#...

• PHY settings (speed and duplex mode of the either LAN or PC port are restored to "automatic") • VLAN settings (disabled) • Terminal number settings (restored to "automatic") To perform IP Reset In cases when buttons/soft key icons are shown in English alphabet1. Base unit: [MENU] (...

2. [ ]/[ ]: Select the desired terminal number (" Auto ", " Terminal 1 "–" Terminal 9 ") ® 3. Base unit: [ ] Handset: [ ] 2.1.6 Reset Web ID/Password Reset Web ID/Password resets all the IDs and passwords required for users and administrators to access theWeb user interface (...

3.1 Web User Interface Setting List The following tables show all the settings that you can configure from the Web user interface and the accesslevels. For details about each setting, see the reference pages listed. Status Menu Item Section Title Setting Access Level *1 Ref. U A VersionInformation V...

Network Menu Item Section Title Setting Access Level *1 Ref. U A Basic NetworkSettings Connection Mode Connection Mode *2 ü *3 ü Page 62 DHCP Settings Host Name *4 ü Page 62 Domain Name Server *2 ü *3 ü Page 63 Static Settings Static IP Address *2 ü *3 ü Page 63 Subnet Mask *2 ü *3 ü Page 64 Default...

Menu Item Section Title Setting Access Level *1 Ref. U A Static NAPTSettings Global IP Address Global IP Address ü Page 72 Enable Global IPAddress Usage per Line Line 1–Line 8 ü Page 72 External RTP Port Channel 1–3 ü Page 72 *1 The access levels are abbreviated as follows:U: User; A: AdministratorA...

Menu Item Section Title Setting Access Level *1 Ref. U A Time AdjustSettings Synchronization Enable Synchronization byNTP ü *3 ü Page 77 Synchronization Interval *2 ü *3 ü Page 77 Time Server NTP Server Address *2 ü *3 ü Page 78 Time Zone Time Zone *2 ü *3 ü Page 78 Daylight Saving Time(Summer Time)...

Menu Item Section Title Setting Access Level *1 Ref. U A VoIP Settings[Line 1]–[Line 8] Quality of Service (QoS) RTP Packet QoS (DSCP) *2 ü Page 93 Statistical Information RTCP Interval *2 ü Page 93 Jitter Buffer Maximum Delay *2 ü Page 93 Minimum Delay *2 ü Page 94 Initial Delay *2 ü Page 94 DTMF D...

Menu Item Section Title Setting Access Level *1 Ref. U A Tone Settings Dial Tone Tone Frequencies *2 ü Page 112 Tone Timings *2 ü Page 112 Busy Tone Tone Frequencies *2 ü Page 113 Tone Timings *2 ü Page 113 Ringing Tone Tone Frequencies *2 ü Page 113 Tone Timings *2 ü Page 114 Stutter Tone Tone Freq...

Menu Item Section Title Setting Access Level *1 Ref. U A ProvisioningMaintenance ProvisioningMaintenance Enable Provisioning *2 ü Page 120 Standard File URL *2 ü Page 121 Product File URL *2 ü Page 121 Master File URL *2 ü Page 121 Cyclic Auto Resync *2 ü Page 122 Resync Interval *2 ü Page 122 Heade...

Configuring Settings from the Base Unit (KX-TGP550 only)/Handset To open the unit’s Web port In cases when buttons/soft key icons are shown in English alphabet1. Base unit: [MENU] (middle soft key) ® [#][5][3][4] Handset: [MENU] (center of joystick) ® [#][5][3][4] 2. [ ]/[ ]: Select " On " f...

Controls on the Window The Web user interface window contains various controls for navigating and configuring settings. The followingfigure shows the controls that are displayed on the [Basic Network Settings] screen as an example: A C D B Note • The screen shots shown are taken from the Web user in...

Button Function Refresh Updates the status information displayed on the screen. This button isdisplayed in the upper-right area of the [Network Status] and [VoIP Status] screens. Entering Characters In the Web user interface, when specifying a name, message, password, or other text item, you can ent...

3.3.1 Version Information This screen allows you to view the current version information such as the model number and the firmwareversion of the unit. 3.3.1.1 Version Information Model Description Indicates the model number of the unit (reference only). Value Range Model number Default Value Current...

Default Value Current firmware version 3.3.2 Network Status This screen allows you to view the current network information of the unit, such as the MAC address, IPaddress, Ethernet port status, etc.Clicking [Refresh] updates the information displayed on the screen. 3.3.2.1 Network Status MAC Address...

DNS2 Description Indicates the specified IP address of the secondary DNS server(reference only). Note • If the secondary DNS server address is not specified, this fieldwill be left blank. Value Range IP address of the secondary DNS server Default Value Not applicable. 3.3.3 VoIP Status This screen a...

Default Value Not applicable. VoIP Status Description Indicates the current VoIP status of each line (reference only). Value Range • Registered: The unit has been registered to the SIP server, and theline can be used. • Registering: The unit is being registered to the SIP server, and theline cannot ...

for " Embedded web " on the base unit (KX-TGP550 only) or handset ( ® see Opening/Closing the Web Port in 3.2.1 Before Accessing the Web User Interface ). 3.4.1.1 Connection Mode Connection Mode Description Selects whether to assign the IP address automatically (DHCP) ormanually (static). Va...

DNS2 Description Specifies the IP address of the secondary DNS server. Note • This setting is available only when [Connection Mode] is set to [Static] . Value Range Max. 15 characters ("n.n.n.n" [n=0–255], except "0.0.0.0","255.255.255.255", "127.0.0.1", etc.) Default...

3.4.3 HTTP Client Settings This screen allows you to change the HTTP client settings for the unit in order to access the HTTP server ofyour phone system and download configuration files. 3.4.3.1 HTTP Client Settings HTTP Version Description Selects which version of the HTTP protocol to use for HTTPc...

Value Range Max. 127 characters Default Value Not stored. Configuration File Reference STUN_SERV_ADDR (Page 159) STUN Server Port Description Specifies the port number of the STUN server. Value Range 1–65535 Default Value 3478 Configuration File Reference STUN_SERV_PORT (Page 159) 3.4.5 Static NAPT ...

3.4.5.1 Global IP Address Global IP Address Description Specifies the global IP address of your network. Note • You must enter a value in this field if at least 1 of [Line 1] – [Line 8] is set to [Yes] , or when port numbers are specified in [Channel 1–3] . • The global IP address will reflect SIP m...

3.5 System This section provides detailed descriptions about all the settings classified under the [System] tab. 3.5.1 Web Language This screen allows you to select the language used for the Web user interface. The language setting is onlyapplicable when you log in to the Web user interface as User....

3.5.2 Administrator Password This screen allows you to change the password used to authenticate the Administrator account when loggingin to the Web user interface. Note • For security reasons, the characters entered for the password are masked by special characters, whichdiffer depending on the Web ...

Default Value Not stored. Configuration File Reference USER_PASS (Page 135) 3.5.4 Web Server Settings This screen allows you to change the Web server settings. 3.5.4.1 Web Server Settings Web Server Port Description Specifies the port number used by the Web server. Value Range 80, 1024–49151 Note • ...

3.5.5 Time Adjust Settings This screen allows you to enable automatic clock adjustment using an NTP server and configure the settingsfor DST (Daylight Saving Time), also known as Summer Time. 3.5.5.1 Synchronization Enable Synchronization by NTP Description Selects whether to enable the unit to auto...

Value Range • Sunday • Monday • Tuesday • Wednesday • Thursday • Friday • Saturday Default Value Sunday Configuration File Reference DST_STOP_DAY_OF_WEEK (Page 139) Time Description Specifies the end time of DST (Summer Time) in minutes after 12:00AM. Value Range 0–1439 Default Value 120 Configurati...

3.6.1.1 SIP Setting SIP User Agent Description Specifies the text string to send as the user agent in the headers of SIPmessages. Value Range Max. 40 characters Note • You cannot leave this field empty. • If "{mac}" is included in this field, it will be replaced with theunit’s MAC address in...

3.6.2 SIP Settings [Line 1]–[Line 8] This screen allows you to change the SIP settings that are specific to each line. 3.6.2.1 Phone Number Phone Number Description Specifies the phone number to use as the user ID required forregistration to the SIP registrar server. Value Range Max. 24 characters (...

Value Range Max. 127 characters Default Value Not stored. Configuration File Reference SIP_RGSTR_ADDR_[1–8] (Page 180) Registrar Server Port Description Specifies the port number to use for communication with the SIPregistrar server. Value Range 1–65535 Default Value 5060 Configuration File Referenc...

Value Range 1–65535 Default Value 5060 Configuration File Reference SIP_PRSNC_PORT_[1–8] (Page 189) 3.6.2.3 Outbound Proxy Server Outbound Proxy Server Address Description Specifies the IP address or FQDN of the SIP outbound proxy server. Value Range Max. 127 characters Default Value Not stored. Con...

Value Range 1024–49151 Note • You cannot specify here the same port number as any of theport numbers in [Channel 1–3] in 3.4.5.3 External RTP Port (if they are configured). In addition, you cannot specify a portnumber that is 1 greater than a port number specified in [Channel 1–3] . • The SIP port n...

Supports Session Timer (RFC 4028) Description Specifies the length of time, in seconds, that the unit waits beforeterminating SIP sessions when no reply to repeated requests isreceived. For details, refer to RFC 4028. Value Range 0, 60–65535 (0: Disable) Default Value 0 Configuration File Reference ...

Configuration File Reference RTP_PORT_MIN (Page 173) Maximum RTP Port Number Description Specifies the highest port number that the unit will use for RTP packets. Note • If port numbers are specified in [Channel 1–3] in 3.4.5.3 External RTP Port , this setting is ignored and the corresponding extern...

3.6.4.1 Quality of Service (QoS) RTP Packet QoS (DSCP) Description Selects the DSCP level of DiffServ applied to RTP packets. Value Range • Best Effort (default) (000 000) • AF11 (Class1/Level Low) (001 010) • AF12 (Class1/Level Medium) (001 100) • AF13 (Class1/Level High) (001 110) • AF21 (Class2/L...

Value Range • G722 • PCMA (G.711 A-law) • G726-32 (G.726 [32k]) • G729A • PCMU (G.711 µ-law) Note • You can select each codec on once within [CODEC Settings] . • A maximum of 5 priorities can be assigned. If only 4 codecs arespecified in a configuration file, you will be able to select fromonly 4 co...

Value Range • G722 • PCMA (G.711 A-law) • G726-32 (G.726 [32k]) • G729A • PCMU (G.711 µ-law) Note • You can select each codec on once within [CODEC Settings] . • A maximum of 5 priorities can be assigned. If only 4 codecs arespecified in a configuration file, you will be able to select fromonly 4 co...

Value Range Selected, Not selected Note • If you clear all the check boxes for the base unit and thehandsets, calls cannot be made from either the base unit or thehandsets. Default Value Selected (all) Default Description Selects which line to seize automatically when going off-hook to makea call fo...

3.7.2.1 Call Control Send SUBSCRIBE to Voice Mail Server Description Selects whether to send the SUBSCRIBE request to a voice mailserver. Note • Your phone system must support voice mail. Value Range • Yes • No Default Value No Configuration File Reference VM_SUBSCRIBE_ENABLE (Page 162) Conference S...

3.7.3 Call Control [Line 1]–[Line 8] This screen allows you to configure various call features that are specific to each line. 3.7.3.1 Call Control Display Name Description Specifies the name to display as the caller on the other party’s phonewhen you make a call. Value Range Max. 16 characters or 3...

Do Not Disturb Description Selects whether to enable the Do Not Disturb feature for incoming calls. Note • If Do Not Disturb has been enabled on the server, the serverrejects incoming calls and the unit does not receive any calls,even if you have selected [No] for this setting. • If you change this ...

Note • If the existing phonebook data has an entry with the same name and phone number as an importedentry, the imported entry is not added as a new entry. The import is still successful, and themessage "Complete" will be displayed. • When you begin transferring the phonebook data, the "...

File Name Description Specifies the path of the firmware file to be imported. Value Range No limitation Note • There are no limitations for the field entry. However, it isrecommended that paths of less than 256 characters be used:longer paths may cause longer data transfer times and result inan inte...

Configuration File Reference CFG_MASTER_FILE_PATH (Page 146) Cyclic Auto Resync Description Selects whether the unit periodically checks for updates of configurationfiles. Value Range • Yes • No Default Value No Configuration File Reference CFG_CYCLIC (Page 148) Resync Interval Description Specifies...

Notice • After resetting the settings, the base unit will restart even if it is being accessed through the phone userinterface, or on calls. Note • If you have changed the default password for the Administrator account and successfully reset thesettings (the message "Complete" is displayed),...

4.1 Configuration File Parameter List The following tables show all the parameters that can be programmed using configuration file programming.For details about each parameter, see the reference pages listed. System Settings Category Parameter Name Ref. Login Account Settings ADMIN_ID Page 134 ADMIN...

Category Parameter Name Ref. Provisioning Settings OPTION66_ENABLE Page 143 PROVISION_ENABLE *1 Page 144 CFG_STANDARD_FILE_PATH *1 Page 144 CFG_PRODUCT_FILE_PATH *1 Page 145 CFG_MASTER_FILE_PATH *1 Page 146 CFG_FILE_KEY1 Page 147 CFG_FILE_KEY2 Page 148 CFG_FILE_KEY3 Page 148 CFG_FILE_KEY_LENGTH Page...

Category Parameter Name Ref. Ethernet Port Settings VLAN_ENABLE *1 Page 155 VLAN_ID_IP_PHONE *1 Page 155 VLAN_PRI_IP_PHONE *1 Page 155 VLAN_ID_PC *1 Page 156 VLAN_PRI_PC *1 Page 156 HTTP Settings HTTP_VER *2 Page 156 HTTP_USER_AGENT *2 Page 157 HTTP_SSL_VERIFY Page 157 CFG_ROOT_CERTIFICATE_PATH Page...

Category Parameter Name Ref. Tone Settings DIAL_TONE_FRQ *1 Page 162 DIAL_TONE_TIMING *1 Page 163 BUSY_TONE_FRQ *1 Page 163 BUSY_TONE_TIMING *1 Page 163 RINGING_TONE_FRQ *1 Page 164 RINGING_TONE_TIMING *1 Page 164 STT_TONE_FRQ *1 Page 164 STT_TONE_TIMING *1 Page 164 REORDER_TONE_FRQ *1 Page 165 REOR...

Category Parameter Name Ref. RTP Settings TOS_RTP_[1–8] *1 Page 170 RTCP_INTVL_[1–8] *1 Page 171 MAX_DELAY_[1–8] *1 Page 171 MIN_DELAY_[1–8] *1 Page 172 NOM_DELAY_[1–8] *1 Page 172 RTP_PORT_MIN *1 Page 173 RTP_PORT_MAX *1 Page 173 RTP_PTIME *1 Page 173 Miscellaneous VoIP Settings OUTBANDDTMF_[1–8] *...

Category Parameter Name Ref. SIP_OUTPROXY_ADDR_[1–8] *1 Page 193 SIP_OUTPROXY_PORT_[1–8] *1 Page 193 SIP_TRANSPORT_[1–8] *1 Page 193 SIP_ANM_DISPNAME_[1–8] Page 194 SIP_ANM_USERNAME_[1–8] Page 194 SIP_ANM_HOSTNAME_[1–8] Page 194 SIP_DETECT_SSAF_[1–8] *1 Page 195 PHONE_NUMBER_[1–8] *1 Page 195 DISPLA...

No space characters are allowed. Description Describes the details of the parameter. Value Range Indicates the permitted value range of the parameter. Default Value Indicates the factory default value of the parameter.Actual default values may vary depending on your phone system dealer. Phone User I...

Value Range 00:00–23:59 Note • If the value for this setting is any valid value other than an emptystring, the unit downloads the configuration files at the fixedtime, and the settings specified in " CFG_CYCLIC ", " CFG_CYCLIC_INTVL ", and " CFG_RTRY_INTVL " are disabled. • I...

Value Range 0–3 – 0: Enable "Basic Network Settings" and "Time Adjust Settings" – 1: Disable "Basic Network Settings" – 2: Disable "Time Adjust Settings" – 3: Disable "Basic Network Settings" and "Time Adjust Settings" Default Value 0 4.5 Telephone Set...

5.1 Line Settings for Base Unit and Handset 5.1.1 Multi Number Settings A unit can be used with a single base unit and 6 handsets.You can assign a maximum of 8 different phone numbers for the base unit (KX-TGP550 only) and handsets.Each available phone number (line) can be assigned to the base unit ...

Programming Example 2 The following programming example shows a configuration where handsets 1–3 dial with lines 1–3,respectively. Each handset uses the line set in [Default] by default. You can program this table using Web user interface programming ( ® see 3.7.1.2 Handset and Line No. selection fo...

You can export the phonebook data to the PC, edit the exported file using appropriate software, and then importit into the unit. Microsoft Excel Phonebook data B A C D Importing Address Book Data from a PC You can import address book data stored in programs, such as Microsoft Outlook ® messaging and...

You can also import phonebook data created on a PC to other base units, handsets, or another unit. B A Microsoft Excel Phonebook data Import/Export File Format The file format used for importing and exporting the phonebook data is "TSV". When importing or exportingusing Microsoft Excel, "...

Phonebook Data in Binary Format A D B C A BOM B Space between the first name and last name C Tab D Line feed 5.2.1 Import/Export Operation The following procedures explain how to import phonebook data to units, and how to export phonebook datafrom units to a PC through the Web user interface.For det...

For details about available characters for the dial format, see Available Values for the Dial Plan Field in this section. 3. Select [Yes] or [No] for [Call Even If Dial Plan Does Not Match] . • If you select [Yes] , the call will be made even if the user dials a phone number that does not match the ...

Element Available Value Description Alternation | Example: "1xxxx|2xxx" If the dialed phone number is "1" followed by 4 digits, or "2"followed by 3 digits, the call is made immediately.You can use this element to specify multiple numbers. Note • You can enter up to 500 charac...

6.1 Firmware Server Setup No special server is necessary for the firmware update. You can use an HTTP, HTTPS, FTP, or TFTP serveras the firmware server by simply setting its URL. 6.2 Firmware Update Settings Firmware updates are provided by the manufacturer when necessary.The firmware update will be...

6.3 Executing Firmware Update After configuring the firmware update settings in the configuration file, the firmware will be updated when theconfiguration file is downloaded.The firmware update will be performed only when a newer version of the firmware file (i.e., one that has a largerversion numbe...

7.1 Troubleshooting If you still have difficulties after following the instructions in this section, disconnect the base unit’s AC adaptor,then reconnect the base unit’s AC adaptor. Remove the batteries from the handset, and then insert the batteriesinto the handset again. General Use Problem Cause/...

Problem Cause/Solution I cannot make a call. • Check if the STATUS indicator or indicator is lit in green. If it is not lit in green, refer to the User Guide on thePanasonic Web site ( ® see Introduction ). • You cannot make a call while the base unit is downloadingthe firmware update. Wait until th...

Time Problem Cause/Solution The time is not correct. • Adjust the date and time of the unit. For details about theoperations, refer to the User Guide on the Panasonic Website ( ® see Introduction ). • In the Web user interface, you can set NTPsynchronization and DST (Summer Time) control to adjustth...

8.1 Simplified Example of the Configuration File The following listing shows an example of a simple configuration file.For the programming instructions and allowable characters, see 4.2 General Information on the Configuration Files . Simplified Example # PCC Standard Format File # DO NOT CHANGE THI...

OUTBANDDTMF_1="Y" ############################################################# Call Control Settings ############################################################# # Enables subscription to the Voice Mail serverVM_SUBSCRIBE_ENABLE="Y" # Shared Call SettingsSHARED_CALL_ENABLE_1="Y...

SIP_OUTPROXY_PORT_2="5060"SIP_TRANSPORT_2="0"SIP_ANM_DISPNAME_2="1"SIP_ANM_USERNAME_2="0"SIP_ANM_HOSTNAME_2="N"SIP_DETECT_SSAF_2="N"PHONE_NUMBER_2="1234567891"DISPLAY_NAME_2="1234567891" #------------------------------------------------...

8.3 Example with Incorrect Descriptions The following listing shows an example of a configuration file that contains incorrect formatting: An improper description is entered in the first line. A configuration file must start with the designatedcharacter sequence " # PCC Standard Format File # &#...

Index Document Version 2010.03.15 Administrator Guide 243

Numerics 1–30 1031–5 103 A Access Level 40, 50Access Levels (IDs and Passwords) 27, 50Accessing the Web User Interface 50ADD_USER_PHONE_[1–8] 192ADMIN_ID 134ADMIN_PASS 135Administrator Password 74Audience 2Authentication ID 86Authentication Password 86Available Values for the Dial Plan Field 207 B B...