Panasonic KX-TEB308 - Manuals

6 Getting Started Precautions for Users in the United Kingdom FOR YOUR SAFETY, PLEASE READ THE FOLLOWING TEXT CAREFULLY. This appliance is supplied with a moulded three-pin mains plug for your safety and convenience. A 5 amp fuse is fitted in this plug. Should the fuse need to be replaced, please en...

8 Getting Started Table of Contents 1 Before Installation .................................................................................. 9 1.1 Unpacking .......................................................................................................................... 9 1.2 System Connect...

Getting Started 9 1 Before Installation 1.1 Unpacking Check the package contents. Main Unit × 1 CD-ROM (including manuals, etc.) × 1 Necessary tools (not supplied): Telephone cable for extension connection: The maximum length of the cable may vary depending on the type of the cables. 2-conductor con...

10 Getting Started 1.2 System Connection Diagram • Connect a display-equipped proprietary telephone (PT) to extension jack 01, as this extension is automatically designated as the manager extension. • For supported extension types, refer to "2.3 Connecting Extensions". Batteries Voice Proces...

Getting Started 11 2 Installation 2.1 Opening Covers 1. Pull the slide button to the right and, holding it, slide the cable cover upwards. Then turn the cable cover slightly to remove it. 2.2 Connecting Outside (CO) Lines 1. Inser t the modular plugs of the telephone line cords (2-conductor wiring) ...

12 Getting Started 2.3 Connecting Extensions Extension jacks can be used for proprietary telephones (PTs), Direct Station Selection (DSS) Consoles, single line telephones (SLTs), and Voice Processing Systems. Notes • Connect a display-equipped proprietary telephone (PT) to extension jack 01, as this...

Getting Started 13 2.4 Securing the Cables 1. Attach the included strap to either of the 2 rails depending on your preference. 2. Bind the cables as shown. Rail Rail

14 Getting Started 2.5 Closing Covers 1. Attach the rear hooks on the cable cover to the main unit, then swing the cable cover closed so that the front hooks fit in place. 2. Slide the cable cover down until it locks. Note For safety reasons, keep the front cover closed while the PBX is in operation...

Getting Started 15 2.6 Wall Mounting The PBX is designed for wall mounting only. The wall where the PBX is to be mounted must be able to support the weight of the PBX. When wall mounting the main unit, use either the included screws, or screws of the same size. 2.6.1 Mounting on a Wooden Wall The in...

16 Getting Started Notes • Do not block the openings of the cabinet. Leave at least 20 cm of space above and 10 cm to the sides of the PBX for ventilation. • Make sure that the wall behind the cabinet is flat and free of obstacles, so that the openings on the back of the cabinet will not be blocked....

Getting Started 17 4. Affix the PBX to the screw heads. Notes • Do not block the openings of the cabinet. Leave at least 20 cm of space above and 10 cm to the sides of the PBX for ventilation. • Make sure that the wall behind the cabinet is flat and free of obstacles, so that the openings on the bac...

Getting Started 19 3 Starting the Advanced Hybrid System 3.1 Starting the Advanced Hybrid System This section explains the procedure for starting the PBX for the first time, with default values, or when you wish to re-initialise the PBX. 1. Make sure that all outside (CO) lines you use are connected...

20 Getting Started CAUTION • The PBX is powered as long as the AC cord is plugged into an AC outlet, even if the Power Switch is set to the "OFF" position. • The power supply cord is used as the main disconnect device. Ensure that the AC outlet is located/installed near the equipment and is ...

Getting Started 21 4 PC Programming 4.1 PC Programming PBX features and settings can be customised using a PC and the KX-TE308 Maintenance Console software. Customisation and maintenance can be done easily and efficiently using Windows-based PC programming software, with graphical icons to guide you...

22 Getting Started 5 PT Programming 5.1 Programming Instructions The PBX can be programmed by entering 3-digit programming numbers with a PT. In this manual, how to programme some features through PT is explained. Required Telephone PBX settings can be customised through system programming by using ...

Getting Started 23 Entering System Programming Mode To enter system programming mode, the system password is required. Note means default value throughout these programming instructions. 5.2 Programming Procedures Notes • means default value throughout these programming instructions. • means to sele...

26 Getting Started 5.2.1 Basic Features Date & Time [000] Notes • The clock starts immediately after the STORE button is pressed. • The PBX supports years from 2004 to 2099. System Speed Dialling Number [001] Note An Outside (CO) Line Access number (9/0 [for New Zealand: 1 or 9], 81 through 83) ...

TEMPLATE FOR WALL MOUNTING Copy or print this template and place it on the wall. Install the screws as marked.If you mount the main unit on a concrete or mortar wall, fit anchor plugs (not included) into the wall beforehand. Hook the unit onto the screw heads. 1. 2. 3. Make sure to set the print siz...