Panasonic FV 0811RFL1 - Manuals

Page 2 - Denotes a hazard that could result in minor injury.; Ducted fans must always be vented to the outdoors.; WARNING; G E N E R A L S A F E T Y I N F O R M A T I O N

2 For Your Safety To reduce the risk of injury, loss of life, electric shock, fire, malfunction, and damage to equipment or property, always observe the following safety precautions. Explanation of symbol word panels The following symbol word panels are used to classify and describe the level of haz...

Page 3 - This product must be properly grounded.; CAUTION; This model is UL listed for tub and shower enclosures.; G E N E R A L S A F E T Y I N F O R M A T I O N C O N T I N U E D

3 Do not install this ventilating fan where interior room temperature may exceed 104°F(40°C). Make sure that the electric service supply voltage is AC 120V, 60Hz. Follow all local electrical and safety codes, as well as the National Electrical Code (NEC) and the Occupation Safety and Health Act (OSH...

Page 4 - D E S C R I P T I O N; DoC Responsible Party: Panasonic Corporation of North America

4 1 1 Part name Part name Appearance Appearance Quantity Quantity Installationinstructions Warranty sheet Grille 1 Self-drilling screw 4 1 TM Flex-Z Fast bracket (with 4 tapping screw- ST4.2X20) 3 inch adaptor connector (optional part) T h e P a n a s o n i c v e n t i l a t i n g f a n m o d e l s ...

Page 5 - D I M E N S I O N S

Unit: inches (mm) 8 0 110 C F M 8 0 110 C F M P i c k - A - F l o w F e a t u r e T h i s p r o d u c t c o m e s w i t h P i c k - A - F l o w s p e e d o p t i o n . T h e P i c k - A - F l o w s w i t c h o n t h e s u r f a c e o f t h e p r o d u c t a l l o w s t h e o p t i o n t o c h o o s ...

Page 6 - Bend down 4 tabs for positioning install the; Connection method for; I N S T A L L A T I O N ( N E W C O N S T R U C T I O N )

2 Self-drilling screws Knock-out hole Junction boxcover Fig.4 Conduit Circular exhaust duct Mastic or approved foil tape 6 TM 3. Adjust the length of Flex-Z Fast bracket to fit the spacing between joists; fix the TM Flex-Z Fast bracket with the other two pre-installed tapping screws. (Fig.3) 4. Remo...

Page 7 - Insert fan body and slide into adaptor assembly; until the flange overlaps the Flex-Z Fast bracket.; I N S T A L L A T I O N ( N E W C O N S T R U C T I O N ) C O N T I N U E D

10 1/2 (270) 10 1/2 (270) 7 10. Take out the mounting springs from clips. (Fig.8) 9. Finish ceiling work. Ceiling hole should be aligned with the inside edge of the flange. (Fig.7) Fig.7 Unit: inches (mm) After finishing the ceiling job, fill gap between flangeand ceillng with caulk or other sealant...

Page 8 - Remove the existing fan and cut ceiling opening.; I N S T A L L A T I O N ( R E T R O F I T )

1. Remove the existing fan and cut ceiling opening. TM Install the Flex-Z Fast bracket to joists by using the 4 pre-installed tapping screws (ST4.2x20). Leave existing ductwork and wiring in place. (Fig.11) 2. Follow the step 1, 4, 5, 7 on page 6. (Before connect the circular exhaust duct to the ada...

Page 9 - M A I N T E N A N C E ( C L E A N I N G )

9 Fig.14 1. Clean grille. (Don’t put into hot water. Use non-abrasive kitchen detergent, wipe dry with clean cloth.) (Fig.14) Routine maintenance must be done every year. Please wear gloves during the cleaning work. M A I N T E N A N C E ( C L E A N I N G ) Disconnect power source before working on ...

Page 10 - P R A C T I C A L G U I D E T O I N S T A L L A T I O N; HVI Certified performance based on HVI Procedures 915, 916, and 920.; S P E C I F I C A T I O N S

10 Properly insulate the area around the fan to minimize building heat loss and gain. (Fig.18)Loose fill or batt insulation can be placeddirectly over the fan housing in the attic.Our fans and fan/light combination units do not create excessive heat that is a common problem with recessed light fixtu...

Page 11 - Panasonic Corporation of North America; P R O D U C T S E R V I C E

Panasonic Corporation of North America www.panasonic.com Printed in China Panasonic Corporation 2018 P 0 3 1 8 - 0 0 8 R F L 1 4 2 0 Warning Concerning Removal of Covers. The unit should be serviced by qualified technicians only. Your product is designed and manufactured to ensure a minimum of maint...