Panasonic FV-05-11VKSL1 - Manuals

Page 2 - For Your Safety; Explanation of symbol word panels; CAUTION; Denotes a hazard that could result in minor injury.; WARNING; GENERAL SAFETY INFORMATION; Do not disassemble the unit for reconstruction.

2 Use this unit only in the manner intended by the manufacturer. If you have any questions, contact the manufacturer. Before servicing or cleaning unit, switch power off at service panel and lock the service disconnecting means to prevent power from being switched on accidentally. When the service d...

Page 3 - This product must be properly grounded.; Spot and Continuous Ventilation:; PLEASE READ PRIOR TO INSTALLING THIS FAN

3 Do not install this ventilating fan where interior room temperature may exceed 104°F(40°C). Make sure that the electric service supply voltage is AC 120V, 60Hz. Follow all local electrical and safety codes, as well as the National Electrical Code (NEC) and the Occupation Safety and Health Act (OSH...

Page 4 - PLEASE READ PRIOR TO INSTALLING THIS FAN CONTINUED; Two Bedrooms Three Bedrooms Four Bedrooms; DESCRIPTION

4 PLEASE READ PRIOR TO INSTALLING THIS FAN CONTINUED These fans are also built to take care of the homeowner’s spot ventilation needs when the room is occupied. The basic fan models allow a choice of three speeds. When fans are equipped with the optional Multi-Speed module, these models kick up to a...

Page 5 - SUPPLIED ACCESSORIES

5 5 Unit: inches (mm) Part name BladeGrilleLens Junction boxAdaptor Part name No. No. DIMENSIONS WIRING DIAGRAM FV-05-11VKL1FV-11-15VKL1 4 5/8 (116) 10 1/4 (260) 3 7/8 (100) 3 7/8 (100) 13 (330) 10 1/4 (260) 5 7/8 (148) 5 7/8 (148) 13 (330) 3 1 /4 ( 8 1 ) 3 1/2 (88) 3 7/8 (98) 12 1/8 (307) 7 3/8 (19...

Page 6 - FEATURE; switch; Factory setting; allows the fan to run continuously; PLUG ‘N PLAY Modular Component Accessories; INDICATION (PLUG ‘N PLAY FUNCTION DEVICES); Note that there is ONLY ONE; Optimum Ventilation Performance:

6 MODEL MODEL 05-11 11-15 110 150 130 50 110 80 AIR VOLUME CFM ( ) All the WhisperGreen Select base models of fans come with Pick-A-Flow speed options. The Pick-A-Flow switch on the face of all WhisperGreen Select fans allows the option to choose 50 – 80 – 110 CFM for the FV-05-11VKL1, FV-05-11VKSL1...

Page 7 - FV-NLVK1 Nite-Glo LED Night Light module; INDICATION (PLUG ‘N PLAY FUNCTION DEVICES) CONTINUED

7 FV-CSVK1 Condensation Sensor module turns the base fan on or boosts to higher speed when humidity is detected when used in combination with the FV-VS15VK1. The Condensation Sensor works based on calculations from the Psychrometric Chart, or combination of Relative Humidity (RH) and Temperature. Th...

Page 8 - INSTALLATION (PLUG ‘N PLAY FUNCTION DEVICES); Remove the connector cover; Bend down 4 tabs for positioning, install the; Adjust the length of Flex-Z Fast bracket as the; Clasp

Base PCB box Slot 8 INSTALLATION (PLUG ‘N PLAY FUNCTION DEVICES) Joist 2 Tapping screws(ST4.2X20) INSTALLATION (NEW CONSTRUCTION) Mastic or approved foil tape 2 Self-drilling screws Knock-out hole Junction boxcover Conduit Circular duct 1. Remove the connector cover 2. Plug in the specified devices ...

Page 9 - Insert fan body and slide into adaptor assy with some; strength, untill the flange overlaps the Flex-Z Fast; the suitable; INSTALLATION (NEW CONSTRUCTION) CONTINUED

9 8. Insert fan body and slide into adaptor assy with some TM strength, untill the flange overlaps the Flex-Z Fast TM bracket. Secure the fan body to Flex-Z Fast bracket by using 2 self-drilling screws, plug connector to receptacle and secure the fan body to adaptor by using machine screw (M4X6). (F...

Page 10 - Remove the existing fan and cut ceiling openning.; screws and put on Flex-Z Fast bracket before; Secure machine screw (M4X6) to the suitable

Fig.12 10 CAUTION CAUTION WARNING Fig.13 INSTALLATION (NEW CONSTRUCTION) CONTINUED INSTALLATION (RETROFIT) 1. Remove the existing fan and cut ceiling openning. 2. Follow the step 1, 4, 5 on page 8 and step 7 on page 9. (Before connect the circular duct to the adaptor, should pull down the circular d...

Page 11 - Disconnect power source before working on unit.

2. Remove the screw as shown in step of Fig.21. Remove the light cover as shown in step of Fig.21. MAINTENANCE (REPLACEMENT OF LAMP) 1. Clean grille. (Don’t put into hot water. Use non-abrasive kitchen detergent, wipe dry with clean cloth) (Fig.17) 2. The grille should be dry after cleaning.3. Remov...

Page 12 - PRACTICAL GUIDE TO INSTALLATION; Specifications for Base Model fans

Panasonic Corporation of North America Panasonic Canada lnc. www.panasonic.com 5770 Ambler Drive, Mississauga, Ontario L4W 2T3www.panasonic.ca Printed in China Properly insulate the area around the fan tominimize building heat loss and gain. (Fig.23)Loose fill or batt insulation can be placeddirectl...