Page 2 - Introduction; Table of Contents; Box should contain the following, including the Quick Start Guide:; Before You Begin Inspect Upon Receipt.; Four silicone rubber feet for shelf mounting.
Thank you for purchasing a Panamax M4315-PRO Power Management with control system interactive functionality, and congratulations on your choice. The M4315-PRO features Panamax’s revolutionary AVM (Automatic Voltage Monitoring) circuit, and our exclusive Linear Filtering Technology (LiFT). To-gether,...
Page 3 - Features Descriptions
Features Descriptions 1 BlueBOLT ™: Remote Power Management technology provides secure, hosted IP (Internet Protocol) system control. With BlueBOLT™, custom electronics installers, integrators and end-users can remotely monitor and control power to home theater equipment by accessing power managemen...
Page 4 - Important Safety Instructions
2 PLEASE NOTE: The lights’ status is obvious, when the outlet is just plain “ ON ” or just plain “ OFF ”. However, there are transition states that cause the lights to blink. The lights will blink when performing a triggered cycle, but when a server initiated cycle command occurs, it just goes “ OFF...
Page 5 - Preset Profile Information
Preset Profile Information 3 DEFAULT OUTLET SEQUENCING (preset profile P1, by outlet #s): Start up: 1→(1 sec)→2→(1 sec)→3→(1 sec)→4→(1 sec)→5→(1 sec)→6→(1 sec)→7→(5 sec)→8Shut down: 8→(5 sec)→7→(5 sec)→6→(1 sec)→5→(1 sec)→4→(1 sec)→3→(1 sec)→2→(1 sec)→1Reboot 1: 1(off)→(30 sec)→1(on)Reboot 2: 2(off)...
Page 6 - The Bubble of Protection; Rear Panel Features Overview; steel retention clip.; TV
The Bubble of Protection GROUND OUTLET 8 OUTLET 7 OUTLET 6 OUTLET 5 OUTLET 4 OUTLET 3 OUTLET 2 OUTLET 1 FILTER BANK 4 FILTER BANK 3 FILTER BANK 2 FILTER BANK 1 CATV / SAT 1 CATV / SAT 2 LAN CAT 5e TELCO DC TRIGGER AC INLET BlueBOLT-CV1 IN O U T GROUND OUTLET 8 OUTLET 7 OUTLET 6 OUTLET 5 OUTLET 4 OUT...
Page 7 - Log into; Troubleshooting; MAC ADDRESS; CHALLENGE KEY; BlueBOLT; Advanced Operation; automation systems within the local network.
5 GETTING SETUP For BlueBOLT ™ BlueBOLT Online Registration Note: Make sure to complete system setup #1 or # 2 before registering. Step 1. Log into http://www.mybluebolt.com for online registration. Your BlueBOLT™ enabled M4315-PRO Power Management Component is completely plug-and-play and does not ...
Page 8 - Identify Connected Equipment; PLEASE NOTE; that the outlets start at No. 8; LAN TEL; FRONT
6 Identify Connected Equipment Use this diagram to write in what pieces of equipment are plugged into each outlet for an easy reference. PLEASE NOTE that the outlets start at No. 8 on the left. The outlet indicator lights on the front panel are numbered 1 through 8 left to right. OUTLET OUTLET OUTLE...
Page 9 - MESSAGE CONSTRUCTS; RS-232 and Telnet Command Set / Protocol Specifications; Command Set/Status Messaging
7 0. OVERVIEW The purpose of this document is to outline the command set used to communicate with and control the M4315-PRO. The data communication feature will most often be used to interface with automation systems. It may also be used to control and configure the unit manually using a standard te...
Page 10 - CONTROLLER COMMANDS
8 RS-232 and Telnet Command Set / Protocol Specifications (Continued) 2.3 Comm. System: Asynchronous, half-duplex 2.4 Baud Rate: 9600bps 2.5 Start Bits: 1 2.6 Data Bits: 8 2.7 Stop Bits: 1 2.8 Parity: None 2.9 Flow Control: None 3. CONTROLLER COMMANDS The following are commands sent by the controlli...
Page 11 - RESET FACTORY SETTINGS
9 RS-232 and Telnet Command Set / Protocol Specifications (Continued) 3.10.2 Action: Sets the linfeed mode to mode. 3.10.3 Response: If mode = ON, $LINEFEED = ON<CR> If mode = OFF, $LINEFEED = OFF<CR> If mode is invalid, $INVALID_PARAMETER<CR> 3.11 RESET FACTORY SETTINGS Resets all...
Page 13 - Responses and Warning Messages
11 RS-232 and Telnet Command Set / Protocol Specifications (Continued) 5. Responses and Warning Messages If unsolicited feedback is enabled, the following warning messages will be transmitted under the conditions outlined in their description. 5.1 OUTLET STATUS CHANGE 5.1.1 Condition: Outlet or trig...
Page 14 - FCC Notice; Reorient or relocate the receiving antenna.; Contacting Customer Service; AC Power; A shielded-type power cord is required in order to meet FCC
FCC Notice This equipment has been tested and found to comply with the limits for a Class B Digital Device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful in-terference in residential installation. This equipment generates, uses, and ...
