Oki 8100e - Manuals - manualsarea.com

Page 2 - PREFACE

Preface 2 PREFACE Every effort has been made to ensure that the information in this document is complete, accurate, and up-to-date. The manufacturer assumes no responsibility for the results of errors beyond its control. The manufacturer also cannot guarantee that changes in software and equipment m...

Page 3 - TABLE OF CONTENTS

Table of Contents 3 TABLE OF CONTENTS Preface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Table of Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 OkiLAN 8100e Configuration . . . . . . . . . . . . ....

Page 5 - Introduction

OkiLAN 8100e Configuration 5 OKILAN 8100E CONFIGURATION Introduction The OkiLAN 8100e is a fast 100BASE-TX/10BASE-T network interfacecard for the OKI C5100, C5300, and B4300 printers. This user’s guideexplains the functionality of the OkiLAN 8100e. Although the 8100e is integral to the C5100, C5300 ...

Page 6 - Specification

OkiLAN 8100e Configuration 6 Specification The C5100 does not support IPX/SPX or EtherTalk functions.Moreover, though IPP and NetBEUI are displayed in Self-Diagnostic Frame types IEEE 802.2 IEEE 802.3 Ethernet-II, SNAP, AUTO Network interface 100BASE-TX 10BASE-T Network protocols TCP/IP Network laye...

Page 7 - From this information:

OkiLAN 8100e Configuration 7 test, AdminManager, WEB and TELNET, use of these protocols is notsupported in the C5100. Self-diagnostic test With the printer power switched on, press the push-button located onthe network interface panel (at the rear of the printer) for more thanthree seconds and relea...

Page 8 - Configuration utility; Available utilities; Utility

OkiLAN 8100e Configuration 8 Configuration utility Available utilities You can configure the OkiLAN 8100e by using one of the followingmethods: Utility Features System requirements Quick Setup Configure the OkiLAN 8100e easily and simply without installing any software packages into your system. You...

Page 9 - Using Quick Setup; You can configure the following:

OkiLAN 8100e Configuration 9 Using Quick Setup Quick Setup utility allows you to configure the OkiLAN 8100e easilyand simply without installing any software packages. You can configure the following: > Enable/disable TCP/IP, NetWare, EtherTalk, NetBEUI protocols. > Set IP address, Subnet Mask ...

Page 10 - Using AdminManager

OkiLAN 8100e Configuration 10 The following explanation uses Windows 98 as an example. 1. Insert the Network Software CD-ROM into the CD-ROM drive. TheSetup Utility starts automatically. If it does not star t, double-click setup.exe in the Windows folder on the CD-ROM. 2. Select [Network Card Setup]...

Page 11 - The following explanation uses Windows 98 as an example.; Installation; Select the appropriate language.

OkiLAN 8100e Configuration 11 To create a NetWare queue, NetWare Client 32 or IntranetWare Clientshould be installed on to your system. The following explanation uses Windows 98 as an example. Installation 1. Insert the Network Software CD-ROM into the CD-ROM drive. TheSetup Utility starts automatic...

Page 12 - Interface; File menu; Item

OkiLAN 8100e Configuration 12 Interface Select [Start]-[Programs]-[OKI Setup Utility]-[Admin Manager]. File menu In the [File] menu, the following item can be selected: Status Menu In the [Status] menu, the following items can be selected: Item Function Search Search printers in your network and lis...

Page 13 - Setup Menu; In this menu, the following items can be selected:

OkiLAN 8100e Configuration 13 Setup Menu In this menu, the following items can be selected: List of Configuration Items Displays current OkiLAN 8100e configuration. Configuration data can be saved as log file. Item Function Oki Device Setup Configure the OkiLAN 7100e, 7100e+, 7200e, 7300e, 8100e. Se...

Page 14 - Oki Device Setup; General Tab

OkiLAN 8100e Configuration 14 Oki Device Setup Oki Device Setup allows you to configure the OkiLAN 8100e. Type theroot password (default value is the last 6 characters of the MACaddress) to configure. Remember that the root password is casesensitive and if the MAC address contains any alpha characte...

Page 15 - This allows you to configure TCP/IP related items.; Location

OkiLAN 8100e Configuration 15 TCP/IP Tab This allows you to configure TCP/IP related items. Location Comments Change root password You can set/change the root password for AdminManager, TELNET and FTP. Location Comments Use TCP/IP Protocol Set TCP/IP protocol as enabled/disabled. Use DHCP/BOOTP Chec...

Page 16 - Netware Tab; This is where you can configure NetWare related items.

OkiLAN 8100e Configuration 16 Netware Tab This is where you can configure NetWare related items. Network PnP Setup ... Configure items related to Network PnP. In this dialogue box, the following items can be configured> Auto IP address Set to get IP address dynamically by Auto IP, enabled or disa...

Page 19 - EtherTalk Tab; This allows you to configure EtherTalk related items; NetBEUI Tab; This allows you to configure NetBEUI related items.

OkiLAN 8100e Configuration 19 EtherTalk Tab This allows you to configure EtherTalk related items NetBEUI Tab This allows you to configure NetBEUI related items. Location Comments Use EtherTalk Protocol Set EtherTalk protocol to enabled/disabled. Printer Name Set EtherTalk Printer object name. Zone N...

Page 20 - SNMP Tab; This allows you to configure SNMP related items.

OkiLAN 8100e Configuration 20 SNMP Tab This allows you to configure SNMP related items. Location Comments Authentic Community This community name is used to check whether incoming SNMP requests have the correct community name or not. The community name is displayed as ****** for security reasons. TR...

Page 24 - POP Tab; This allows you to configure POP related items.

OkiLAN 8100e Configuration 24 POP Tab This allows you to configure POP related items. Some printers support an email reception function (SMTP/POP3)allowing the printer to print PDF and text files attached to emails. Ifthe POP tab is not displayed, your printer does not support thisfunction. Location...

Page 25 - SMTP Tab; In SNMP Tab, you can configure SNMP related items.

OkiLAN 8100e Configuration 25 SMTP Tab In SNMP Tab, you can configure SNMP related items. Location Comments Use SMTP Transmit Protocol Set sending E-Mail via SMTP, enabled or disabled. Use SMTP Receive Protocol Set receiving E-Mail via SMTP, enabled or disabled. SMTP Server Address/Name Set IP addre...

Page 27 - Create a NetWare Queue

OkiLAN 8100e Configuration 27 Create a NetWare Queue By selecting this item, you can create a NetWare queue on theNetWare server from AdminManager. > NetWare Client 32 or IntranetWare Client should be loaded onthe PC on which the AdminManager runs. Also the clientpackage should be configured to a...

Page 29 - Delete NetWare Object; Select an object you want to delete and click [Delete] button.; IP Address Setup

OkiLAN 8100e Configuration 29 Delete NetWare Object By selecting this item, you can delete a NetWare queue/print server/printer from NetWare server by AdminManager. > NetWare Client 32 or IntranetWare Client should be loaded on tothe PC on which the AdminManager runs. Also, the clientpackage shou...

Page 30 - Option Menu

OkiLAN 8100e Configuration 30 > The Ethernet Address (MAC address) is displayed during theself-diagnostic test. 3. AdminManager asks whether you want to initialise the networkinterface card or not. Select [Yes]. Even if you select [No] here,the IP address that you set can be used after turning th...

Page 31 - Help Menu; Using a Web browser

OkiLAN 8100e Configuration 31 Help Menu In the [Help] menu, [About] is available as well as revision informationfor AdminManager. Using a Web browser If the OkiLAN 8100e is connected to the network using TCP/IP, itssettings and the printer menu settings can be configured using a Webbrowser, such as ...

Page 33 - Using TELNET; Set a temporary IP Address on the NIC using the ARP command.

OkiLAN 8100e Configuration 33 Using TELNET The OkiLAN 8100e can be configured using TELNET. TELNET requiresthe OkiLAN 8100e to have a valid IP address configured. If the NICalready has an IP address configured, skip steps one to three below. > Note: Please ensure a valid IP address for you networ...

Page 34 - Login to the network card using TELNET.; root; ‘root’ user needs password to login.

OkiLAN 8100e Configuration 34 4. Login to the network card using TELNET. Example: for IP address 192.168.20.127 $ telnet 192.168.20.127 Trying 192.168.20.127 Connected to 192.168.20.127 Escape character is ‘^]’. EthernetBoard OkiLAN 8100e Ver 01.09 TELNET server. login: root ‘root’ user needs passwo...

Page 35 - Telnet hierarchical structure.

OkiLAN 8100e Configuration 35 Telnet hierarchical structure. Level1 Level2 Level3 1: Setup TCP/IP 1: TCP/IP protocol — 2: IP address — 3: Subnet Mask — 4: Default Gateway — 5: RARP protocol — 6: DHCP/BOOTP protocol — 7: Auto IP Address — 8: DNS server(Pri.) — 9: DNS server(Sec.) — 10: Root password ...

Page 39 - Turn the printer off and on again.

OkiLAN 8100e Configuration 39 5. When configuration is complete, select [Exit Setup] to save yourchange. To exit without saving your modification, select [Quit]. 6. Turn the printer off and on again. The network card continues to use pre-transmission settings until theprinter is turned off and back ...

Page 40 - Using SNMP; Printer trap settings can be made with TELNET and a Web browser.

OkiLAN 8100e Configuration 40 Using SNMP The printer and network card can be managed via a standard SNMPmanagement station. The network card supports SNMPv1, MIB-II andOKI Data Private MIB. In order for the OkiLAN 8100e to be managedcorrectly from an SNMP management station, the OKI Data PrivateMIB ...

Page 41 - Management utility; PrintSuperVision; PrintSuperVision’s main functions are:

OkiLAN 8100e Configuration 41 Management utility PrintSuperVision PrintSuperVision is a web-based application for managing printingdevices connected to a network. It consists of two parts: A web application based on Microsoft web server (InternetInformation Server, IIS or Personal WEB Server, PWS), ...

Page 42 - System requirement; Windows

OkiLAN 8100e Configuration 42 System requirement Windows The main PrintSuperVision application can be installed in any of thefollowing Windows systems. While the PrintSuperVision application may work in Windows 95 withPWS installed, PrintSuperVision may not install or work properly insome versions o...

Page 43 - Supported Browsers; The browsers supported are:

OkiLAN 8100e Configuration 43 Supported Browsers The browsers supported are: Internet Explorer (IE) 4.01 and above. Netscape Navigator 4.0 and above. Opera 5.12 and above. The PrintSuperVision application can be accessed from any Windows,Macintosh, Unix, and Linux desktop that support any of the abo...

Page 44 - Supported Printers; OKIPAGE 8c

OkiLAN 8100e Configuration 44 Supported Printers PrintSuperVision provides general management information for OKI and non-OKI printers connected to the network. For OKI printers,additional details, reports and added features are available. The listbelow indicates the supported printers as of this re...

Page 45 - Supported network interface cards; The list of network interface cards supported is listed below:; Network Interface

OkiLAN 8100e Configuration 45 Supported network interface cards The list of network interface cards supported is listed below: While the network interface card settings are displayed inPrintSuperVision, only a few of the network interface card settings canbe set. For setting any other network interf...

Page 46 - To install the Print SuperVision utility; the server IP address

OkiLAN 8100e Configuration 46 Installation To install the Print SuperVision utility WindowsXP/2000/NT4.0 requires administrator privileges. 1. Insert the Network Software CD-ROM into the CD-ROM drive. TheSetup Utility starts automatically. If it does not star t, double-click setup.exe on the CD-ROM....

Page 47 - Uninstallation

OkiLAN 8100e Configuration 47 Uninstallation To uninstall PrintSuperVision, either select [Start]-[Programs]-[PrintSuperVision]-[Uninstall PrintSuperVision], or from [ControlPanel], select [Add/Remove Programs], select [PrintSuperVision] fromthe index window and click [Add/Remove]. When the uninstal...

Page 48 - Printing utility; OKI LPR; The utility is for those OKI printers which support TCP/IP and; System Requirement

OkiLAN 8100e Configuration 48 Printing utility OKI LPR The OKI LPR Utility is a utility that allows printing data to printersconnected to the network via TCP/IP. This utility is for use withWindows XP, Windows 2000, Windows Me, Windows 98, Windows 95and Window NT4.0. The utility is for those OKI pri...

Page 49 - To install the OKI LPR utility

OkiLAN 8100e Configuration 49 To install the OKI LPR utility The OKI LPR utility requires that the TCP/IP protocol should beinstalled into your Windows system. To install the TCP/IP protocol intoyour Windows system consult your Windows manual. Windows XP/2000/NT4.0 requires administrator privileges....

Page 50 - Stop the OKI LPR Utility.

OkiLAN 8100e Configuration 50 12. Select [Printer] to accept the printer that has been added in the step 1. 13. Enter an IP address at [IP Address] and click [OK]. A printer is added to the main window. Refer to the On-line Help for information on how to use the utility. Uninstallation 1. Stop the O...

Page 51 - MICROSOFT WINDOWS; Overview; NetBEUI

Microsoft Windows 51 MICROSOFT WINDOWS Overview This chapter provides guidelines on how to print over the networkfrom various Microsoft Windows platforms. There are numerous waysof printing from Windows and the exact set-up will vary dependingupon your environment. There are also numerous versions o...

Page 52 - Installation of TCP/IP Protocol; Restart the operating system.; Windows Version

Microsoft Windows 52 Installation of TCP/IP Protocol There are a number of options available when printing using TCP/IPfor Windows. The following table lists the options: 1 These functions are built into Windows and are displayed as options when using the Add Printer Wizard. Although there are some ...

Page 54 - Windows XP

Microsoft Windows 54 Windows 2000 1. Click the [Start] button, select [Settings] and then click on[Network and Dial-up Connections]. 2. Double-click the [Local Area Connection] icon. In the [Local AreaConnection Status] dialogue box, click the [Properties] button. 3. If the TCP/IP protocol is not li...

Page 55 - Network printer IP address configuration; Connect the printer to the network and turn on.

Microsoft Windows 55 6. In the [Select Network Protocol] dialogue box, select [InternetProtocol (TCP/IP)] then click [OK]. 7. The Windows XP installation CD-ROM may be required. Followthe remaining dialogue box prompts. Once the protocol has been installed and configured in Windows, thenext step is ...

Page 56 - When using

Microsoft Windows 56 Do you use the TCP/IP protocol? When using lpr in UNIX and other TCP/IP environments, please select [Yes]. To use in a TCP/IP environment, an IP address should beassigned to the Ethernet board. If [Yes] has been selected and TCP/IP is the only working protocol andthe IP address ...

Page 57 - OkiLPR

Microsoft Windows 57 11. Confirm your configuration. If everything is correct, select [ Exec ute] to ap pl y t he co nfig uratio n. S et-up has now beencompleted. Select [Finish]. Now that both Windows and the printer have been configured to useTCP/IP, the next step is to configure Windows to print ...

Page 58 - To install this port, the following needs to be carried out.

Microsoft Windows 58 Windows NT 4.0 With Windows NT 4.0, you have two options for printing using TCP/IP.They are: > OkiLPR > Microsoft LPR In order to use Microsoft LPR, it must first be installed into youroperating system. NT 4.0 requires administrator privileges. OkiLPR Please follow the pro...

Page 59 - Insert the printer driver for Windows NT4.0.

Microsoft Windows 59 7. In [Name of printer or print queue on that server] type the logicalprinter name "lp" and then click [OK]. 8. Follow the instructions on the screen to finish installing the LPR-compatible printer. If the LPR port is not available, install the Microsoft TCP/IP PrintingS...

Page 60 - OKILPR; To install this port, the following needs to be carried out:

Microsoft Windows 60 OKILPR Please follow the procedure described in the Windows 95/98/Mesection on page 57. Microsoft LPR To install this port, the following needs to be carried out: 1. Select [Start], [Settings], [Control Panel and Printers]. 2. Open the [Printers] folder. 3. Double-click [Add Pri...

Page 61 - IPP; Install printer driver.

Microsoft Windows 61 6. Select [Next]. 7. The [Welcome to the Add Standard TCP/IP Printer Port Wizard]will appear. 8. Select [Next] and provide the following information. Enter[Printer name] or IP address, for example: 192.168.1.31 . If the a b ov e I P addr ess is e n t e r e d , t h e Po r t N a m...

Page 62 - Windows XP requires administrator privileges.

Microsoft Windows 62 Windows XP Windows XP requires administrator privileges. With Windows XP, there are four options for printing using TCP/IP. > OkiLPR > Microsoft LPR > Port 9100 > IPP In order to use Microsoft LPR, it must first be installed on your system. OKILPR Please follow the p...

Page 63 - If the

Microsoft Windows 63 8. Select [Next] and provide the following information. Enter[Printer name or IP address], for example: 192.168.1.31. If the a b ov e I P addr ess is e n t e r e d , t h e Po r t N a m e wi ll d e fa u l t t o IP_192.168.1.31. 9. Select [Next]. [Additional Port Information Requi...

Page 64 - Install printer driver

Microsoft Windows 64 8. Select [Next] and provide the following information. Enter[Printer name or IP address], for example: 192.168.1.31. If the a b ov e I P addr ess is e n t e r e d , t h e Po r t N a m e wi ll d e fa u l t t o IP_192.168.1.31. 9. Select [Next]. [Additional Port Information Requi...

Page 65 - NOVELL NETWARE IPX; NetBEUI Protocol; Network Printer Settings

Novell Netware IPX 65 NOVELL NETWARE IPX IPX is used with Novell NetWare. The OkiLAN 8100e supports Novell 3,4, 5 and 6, and allows print jobs to be directed to the appropriateNovell print queue. Please refer to the relevant section of this manualfor additional information. NetBEUI Protocol NetBEUI ...

Page 68 - file; Printer driver configuration; Set up the printer driver as the default local printer.

Novell Netware IPX 68 6. Select [Have Disk] and insert your Windows XP CD-ROM, openthe Valueadd\msft\net\netbeui folder, click the Netnbf.inf file and then click [Open]. Now the printer has been configured andNetBEUI has been installed, you can configure Windows to printover the network. Printer dri...

Page 71 - NOVELL NETWARE; The OkiLAN 8100e supports the Novell NetWare environment.; Supported Versions and Modes

Novell NetWare 71 NOVELL NETWARE Overview The OkiLAN 8100e supports the Novell NetWare environment. It is necessary to have NetWare Administrator or Supervisor rights tochange the configuration. This guide is for NetWare administrators. Itshould be read in conjunction with the relevant Novell NetWar...

Page 72 - Printing the Network Interface Card Configuration Sheet; Setup Utilities; Use

Novell NetWare 72 Printing the Network Interface Card Configuration Sheet The printer’s configuration page reports information that is requiredfor NetWare configuration. To print a configuration page, while theprinter is switched on, depress the NIC’s push-button for threeseconds and then release. T...

Page 73 - OKI NDPS Gateway

Novell NetWare 73 Configuration Utility section and online help. Below is the NetWareconfiguration page from AdminManager. OKI NDPS Gateway OKI provide a gateway for NDPS. Gateways allow NDPS clients to sendjobs to printers that are not NDPS-aware (that is, printers that are notequipped with embedde...

Page 77 - iPrint; Global access to printers.

Novell NetWare 77 iPrint iPrint is included in NetWare 6 and is Novell’s next generation ofprinting software. It is Novell’s implementation of IPP (InternetPrinting Protocol). iPrint allows users to install, manage and print toprinters through Web browsers regardless of where the printer isphysicall...

Page 79 - UNIX; Configuration; Network Interface card setting; Login as [root] to change the configuration of the OkiLAN 8100e.; arp; command to set a temporary IP address.

UNIX 79 UNIX Overview The OkiLAN 8100e supports many protocols such as LPD, FTP, TELNET,SNMP and IPP, and works within the UNIX environment. To use the network card within the UNIX environment, the followingsteps are required: Configuration Network Interface card setting The first step in installing...

Page 80 - Use the; ping; command to confirm the connection with the

UNIX 80 The Ethernet address (MAC address) 00:80:87:01:00:D2 in the aboveexample can be determined from the network card self-diagnostictest. 3. Use the ping command to confirm the connection with the network interface card. Example: for IP address 192.168.20.127 # ping 192.168.20.127 If there is no...

Page 83 - Operating system configuration; command to confirm connection with the network

UNIX 83 Operating system configuration This section explains how to configure a printer for major UNIXoperating systems. Sun OS 4.x.x (BSD) configuration The following explanation uses Sun OS 4.1.3 and a C5300 printer asexamples. The absolute path of commands and the configurationmethod may differ b...

Page 84 - lpd

UNIX 84 4. Register the printer in the /etc/printcap file. Example: for host name C5300, to create a queue called C5300_lp C5300_lp: \ :lp=:rm=C5300:rp=lp:\ :sd=/usr/spool/C5300_lp:\ :lf=/usr/spool/C5300_lp/C5300_lp_errs: C5300_lp The name of the printer queue lp: The name of the device used to conn...

Page 85 - Sun Solaris 2.x configuration; Admintool

UNIX 85 Sun Solaris 2.x configuration Admintool is normally used to register remote printers on Open Windows. However, it cannot be used here, as the data recipient andqueue have the same name. The procedure below must be used forregistering a remote printer. If Solaris 2.x is connected to the remot...

Page 86 - netstandard; model; lpadmin

UNIX 86 Reset the network interface card settings to default and try to set atemporary IP address. If you still have the problem after resetting thenetwork interface card, consult the network manager. 5. Register the network card as a remote printer server. Example: for host name C5300 a. Stop the p...

Page 88 - rlpdameon –I; inetd

UNIX 88 a. Stop the printer spooler. # /usr/sbin/lpshut b. Add the following line to the /etc/inetd.conf file and register the remote spooler. printer stream tcp nowait root /usr/sbin/ rlpdameon –I c. Restart inetd # /etc/inetd –c 6. Register the remote printer Example: setting up a queue called C53...

Page 89 - command to confirm connection with the network card.

UNIX 89 AIX 4.1.5 configuration The following explanation uses AIX4.1.5 and a C5300 printer as examples.The absolute path of commands and the method of configuring may differwith the OS version. Refer to the workstation’s manual. If an incorrect IPaddress is entered, the network may go down or other...

Page 90 - LPD Printing; lpr; Logical printers

UNIX 90 # smit mkrque b. Select [remote] (the printer connected to the remote host) from [Type of connection]. c. Select [Standard procedure] from Type of remote print. d. Carry out the following settings in [Add a standard remote print queue]. If the configuration differs from below,configure accor...

Page 92 - FTP printing; and; Logical directory

UNIX 92 Verify the printer status using the lpstat command. # lpstat –pC5300_lp > The result of lpstat may not be displayed correctly depending on UNIX operating system specification (e.g. Solaris 2.x). FTP printing FTP (File Transfer Protocol) is used for transferring a file with TCP/IP. Ifthe p...

Page 93 - Server; 31 Password required.; pwd; 57 ”/lp” is current directory; type binary

UNIX 93 220 EthernetBoard OkiLAN 8100e Ver 01.09 FTP Server Name (C5300:<none>) : root 331 Password required. Password: <CR> 230 User Logged in ftp> The network card logical directory structure is hierarchical. Move to thelogical directory; it is not possible to output print data to t...

Page 94 - type; Using binary mode to transfer files.; quote stat; Transfer type: BINARY

UNIX 94 ftp> type Using binary mode to transfer files. ftp> 4. Transfer the print data to the network card using the put command. Two methods of file transfer using the put command are available. Example: transferring print data test.prn ftp> put test.prn Example: transferring print data sp...

Page 95 - Ready

UNIX 95 211-FTP directory status: Ready 211 End of status ftp>

Page 97 - APPLE MACINTOSH; All Macintosh operating systems from OS 8.1 are supported.

Apple Macintosh 97 APPLE MACINTOSH Overview The OkiLAN 8100e supports the Apple Macintosh AppleTalkenvironment. This guide is for administrators and it should be read inconjunction with the relevant Macintosh manual. The latestMacintosh service packs should be installed. Supported Versions All Macin...

Page 98 - There are three items that need to be configured for EtherTalk.; Use EtherTalk Protocol; Please check the Use EtherTalk Protocol checkbox.; Printer Name; Give the Printer Name as you would like it to appear in the Chooser; Zone Nam; AppleTalk Configuration

Apple Macintosh 98 Setup Utilities Use the OKI Network Card Setup Utility (Macintosh) to assign an IPaddress and configure the network interface card. For instructionsplease refer to the Configuration Utility section and on-line help. Configuration There are three items that need to be configured fo...

Page 99 - Macintosh OS X; Run the installer on the driver CD to install the printer’s PPD file.

Apple Macintosh 99 4. Close the AppleTalk configuration page and save changes tocurrent configuration when prompted. 5. Configuration is now complete and you are ready to install yourprinter driver. Please enter your driver CD, run the installer andfollow the on-screen instructions. Macintosh OS X T...

Page 101 - TROUBLESHOOTING; Printer does not print.; PS; or; Automati; Flash ROM Check registers

Troubleshooting 101 TROUBLESHOOTING The network addresses used in this manual are shown for exampleonly. Network addresses used in your installation must be generatedfrom your own network. Self-diagnostic test Printer does not print. Ensure the printer emulation is set to PS or Automati c. NG is pri...

Page 103 - put; NetWare; Printer cannot find the network interface card.; Enable

Troubleshooting 103 If printing with FTP, the User name printed is the User name enteredduring FTP login and the File name printed is the Transmitted filename. If the Print Directory name is indicated in the put command, the File name is not printed. The Printer name printed is the LogicalDirectory ...

Page 104 - Print Server mode; PostScript error; EtherTalk; Not identified by the Chooser and the Setup Utility.

Troubleshooting 104 Print Server mode Check the File Server name set in the NIC and on the File Server are thesame. Check the Printer name set in the File Server and the NetWare Portname set in the NIC are the same. If there are multiple NICs, configurethe NetWare Port names to be different. Check t...

Page 105 - The network interface card is not identified.

Troubleshooting 105 If the network resides in a Zone, check the correct Zone name isselected in the Chooser. Check the Zone name in the utility related to the NIC is the same as theZone name set in NIC. Check AppleTalk, which is displayed at the right bottom of theChooser, is set to Enable . (In som...

Page 106 - Error writing to Prn1.; Glossary

Troubleshooting 106 Error writing to Prn1. Check the printer is online. If there is an error message indicating the paper has run out, addmore paper and cancel the error. Check whether another user is printing. Print after the other user hasfinished. Glossary NIC Network Interface Card NDS Novell Di...