Page 2 - WARNING; and other hidden utilities.; TO REDUCE THE RISK OF A RANGE TOP GREASE FIRE:; late on fan or filter.; INTENDED FOR DOMESTIC COOKING ONLY
- 2 - WARNING TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS,OBSERVE THE FOLLOWING: 1. Use this unit only in the manner intended by the manufacturer. If you have questions, contact the manufacturer at the address or telephone number listedin the warranty. 2. Before servicing or cle...
Page 3 - CAUTION; Take care when using cleaning agents or detergents.; explosion will result.
- 3 - ! CAUTION 1 . To reduce risk of fire and to properly exhaust air, be sure to duct air outside. Do not vent exhaust air into spaces within walls or ceilings or into attics, crawlspaces, or garages. 2. Take care when using cleaning agents or detergents. 3. Avoid using food products that produce ...
Page 4 - OPERATION; Controls; HALOGEN BULBS; Loosen the ring nut by turning it counter-
- 4 - OPERATION Controls The hood is operated using the slide con-trols under the bottom of the hood. The light switch turns the lamps on and off. The blower switch turns the blower on tothree speed settings: 0 - OFF1 - LOW SPEED2 - MEDIUM SPEED3 - HIGH SPEED The pilot lamp lights up whenever the bl...
Page 5 - FUSE REPLACEMENT; Raise or remove the lower decorative flue.; MAINTENANCE
- 5 - FUSE REPLACEMENT IF LIGHTS FAIL TO OPERATE, DISCON-NECT POWER AT THE SER VICE EN-TRANCE. CHECK THE FUSE AND RE-PLACE IF NECESSARY. 1. Raise or remove the lower decorative flue. 2. Remove the cover from the fuse box. 3. Unscrew the cap from the fuse holder and remove the fuse. 4. Replace the fu...
Page 6 - CONT’D; Hood Cleaning; Hot water with soap or detergent is all that is usually needed.; DO NOT allow deposits to remain for long periods of time.; adhere to the surface causing rust.
- 6 - MAINTENANCE, CONT’D Hood Cleaning Stainless steel is one of the easiest materials to keep clean. Occasional care willhelp preserve its fine appearance. Cleaning tips: 1. Hot water with soap or detergent is all that is usually needed. 2. Follow all cleaning by rinsing with clear water. Wipe dry...
Page 7 - PREPARE THE HOOD; Unpack hood and check contents.
- 7 - PREPARE THE HOOD Unpack hood and check contents. You should receive: 1 - Hood1 - Decorative Flue Assembly1 - Parts Bag : 1 - Mounting Bracket1 - Discharge Collar1 - Flue Mounting Bracket8 - Mounting Screws (4.8 x 38mm Pan Head)7 - Mounting Screws (3.9 x 9.5mm Pan Head)2 - Bracket Screws (3.9 x...
Page 8 - INSTALL ELECTRICAL; WARNING: Electrical wiring must be; INSTALL THE DUCTWORK; CAUTION: To reduce the risk of fire, use
- 8 - INSTALL ELECTRICAL WARNING: Electrical wiring must be done by a qualified person(s) in accor-dance with all applicable codes and stan-dards. This range hood must be prop-erly grounded. Turn off electrical powerat service entrance before wiring. 1. Plan where the hood will be located above the ...
Page 9 - INSTALL MOUNTING BRACKET; FLUE MOUNTING
- 9 - DRYWALL INSTALL MOUNTING BRACKET (DUCTED AND NON-DUCTED HOODS) 1. Construct wood wall framing that is flush with interior surface of wall studs.Make sure: a) the framing is centered over installa- tion location. b) the height of the framing will allow the mounting bracket to be secured tothe f...
Page 11 - CAUTION: Do not use plastic or rigid metal ducting.; PLUS 12” If ceiling
- 11 - PREPARE THE HOOD (NON-DUCTED HOODS ONLY) Note: The following materials must be purchased separately for non-ducted recircu-lation installations. Non - Ducted Recirculation Kit, Model RRK51.5” diameter expandable / flexible aluminum duct.1/16” diameter twist drill. ! CAUTION: Do not use plasti...
Page 12 - INSTALL THE HOOD
- 12 - PREPARE THE HOOD (CONT’D) (NON-DUCTED HOODS ONLY) 8. Carefully slide the upper decorative flue down inside the lower flue. 9. Carefully place the decorative flues into the recessed area of the range hood top. Note: Air vents must be up. ROOMS WITH 10-FOOT CEILINGSRooms with 10-Foot ceilings r...
Page 13 - INSTALL FILTERS; To remove the GREASE filter, push in on the metal; WARRANTY
- 13 - INSTALL FILTERS (DUCTED AND NON-DUCTED HOODS) 1. To remove the GREASE filter, push in on the metal latch tab. This will disengage the filter from thehood. Tilt the filter downward and remove. 2. To install the GREASE filter, align rear filter tabs with slots in the hood. Push in the metal lat...
Page 14 - SERVICE PARTS
Page 15 - DESCRIPTION
- 15 - SERVICE PARTS MODEL RM53000 KEY NO. PART NO. DESCRIPTION 9 B08087294 Grease Filter 1 4 B02300233 Motor Capacitor 1 6 BE3346354 Electrical Box Support 1 9 B03295005 Terminal Box 2 6 B02300891 Halogen Lamp Bulb 3 7 B02300787 Heat Sentry 4 5 BW0000019 Blower 4 8 B02310203 Motor 4 9 B03295076 Blo...
Page 16 - AVERTISSEMENT; non-apparents lors de la découpe ou du perçage du mur ou du plafond.; POUR USAGE DOMESTIQUE SEULEMENT
- 16 - AVERTISSEMENT AFIN DE RÉDUIRE LES RISQUES D'INCENDIE, DE CHOC ÉLECTRIQUE OU DEBLESSURES CORPORELLES, VEUILLEZ OBSERVEZ LES DIRECTIVESSUIVANTES : 1. N'utilisez cet appareil que de la manière prévue par le fabricant. Si vous avez des questions, communiquez avec le fabricant à l'adresse ou au nu...
Page 17 - ATTENTION; et du poids de cette hotte.; NE SOULEVEZ JAMAIS UNE CASSEROLE EN FLAMMES - vous pourriez
- 17 - ! ATTENTION 1 . Pour réduire les risques d'incendie et évacuer l'air correctement, assurez- vous qu'il est canalisé à l'extérieur. N’évacuez pas l'air dans des espacesenfermés par des murs ou un plafond ou dans un grenier, un vide sanitaire ouun garage. 2. Faites attention lorsque vous utilis...
Page 18 - UTILISATION; Commandes; AVERTISSEMENT : Le thermostat HEAT SENTRY peut faire démarrer le; AMPOULES HALOGÈNES; AVERTISSEMENT : Coupez toujours
- 18 - UTILISATION Commandes La hotte fonctionne à l'aide de la commandepar curseur située sous le dessous de lahotte. L'interrupteur d'éclairage allume et éteintles lampes. L'interrupteur de ventilateur fait démarrerle ventilateur à trois régimes différents : 0 - ARRÊT1 - RÉGIME LENT2 - RÉGIME MOYE...
Page 19 - ENTRETIEN
- 19 - REMPLACEMENT DUFUSIBLE SI LES LUMIÈRES NE S'ALLUMENT PAS,COUPEZ LE COURANT AU PANNEAUD ' A L I M E N TAT I O N É L E C T R I Q U E .VÉRIFIEZ LE FUSIBLE ET REMPLACEZ-LE, LE CAS ÉCHÉANT. 1. Soulevez ou enlevez le conduit décoratif inférieur. 2. Enlevez le couvercle de la boîte à fusibles.3. Dév...
Page 20 - SUITE; Nettoyage de la hotte; Conseils de nettoyage :
- 20 - ENTRETIEN, SUITE Nettoyage de la hotte L'acier inoxydable est l'un des matériaux les plus faciles à nettoyer. Quelques soinscontribueront à préserver sa belle apparence. Conseils de nettoyage : 1. Il suffit habituellement d'utiliser de l'eau chaude savonneuse ou additionnée de détergent. 2. A...
Page 21 - PRÉPARATION DE LA HOTTE; Déballez la hotte et vérifiez le contenu de la boîte.
- 21 - PRÉPARATION DE LA HOTTE Déballez la hotte et vérifiez le contenu de la boîte. Celle-ci doit contenir les éléments suivants : 1 - Hotte1 - Conduit décoratif de cheminée1 - Sac de pièces : 1 - Bride de montage1 - Collier de sortie1 - Bride de montage du conduit décoratif8 - Vis de montage (4,8 ...
Page 22 - CÂBLAGE; AV E R T I S S E M E N T : L e s t r a v a u x; POSE DU CONDUIT; ATTENTION : Pour réduire les risques
- 22 - CÂBLAGE AV E R T I S S E M E N T : L e s t r a v a u x d'électricité doivent être effectués pardes personnes qualifiées en respectantles codes et les normes en vigueur.C e t t e h o t t e d e c u i s i n e d o i t ê t r ec o r r e c t e m e n t m i s e à l a t e r r e . A v a n td’effecteur l...
Page 23 - INSTALLATION DE LA BRIDE DE MONTAGE; BRIDE DE
- 23 - CLOISONSÈCHE INSTALLATION DE LA BRIDE DE MONTAGE (HOTTES AVEC OU SANS CONDUIT) 1. Construisez une charpente de bois qui affleure la surface intérieure des montantsdu mur.Prenez soin : a) d e c e n t r e r c e t t e c h a r p e n t e a v e c l'emplacement d'installation. b) de donner une haute...
Page 25 - Jetez le collier/clapet de sortie fourni; MOINS Distance au dessus
- 25 - PRÉPARATION DE LA HOTTE (HOTTES SANS CONDUIT SEULEMENT)Remarque : Le matériel suivant doit être acheté séparément pour les installationssans conduit avec recirculation. Ensemble de recirculation pour installation sans conduit, modèle RRK51.Conduit d'aluminium flexible / extensible de 12,7 cm ...
Page 27 - GARANTIE
- 27 - INSTALLATION DESFILTRES (HOTTES AVEC OU SANS CONDUIT) 1. Pour enlever le filtre à GRAISSE, enfoncez la languette métallique. Le filtre se dégagera de lahotte. Inclinez le filtre vers le bas et enlevez-le. 2. Pour installer le filtre à GRAISSE, alignez les pattes arrière du filtre dans les fen...
Page 28 - LISTE PIECES DE RECHANGE
Page 29 - PIÈCES DE RECHANGE; REPÈRE
- 29 - PIÈCES DE RECHANGE MODÈLE RM53000 REPÈRE N° de PIÈCE DESCRIPTION 9 B08087294 1 4 B02300233 1 6 BE3346354 1 9 B03295005 2 6 B02300891 3 7 B02300787 4 5 BW0000019 4 8 B02310203 4 9 B03295076 5 3 B03202007 6 0 B02300249 6 2 B08091462 6 4 BE3347000 8 6 B08088378 113 B03202433 118 BE3347192 119 BE...
Page 30 - ADVERTENCIA; eléctrico ni otros servicios ocultos.; INDICADA SOLAMENTE PARA COCINAR EN CASA
- 30 - ADVERTENCIA PARA REDUCIR EL RIESGO DE INCENDIOS, DESCARGAS ELÉCTRICAS OLESIONES PERSONALES, OBSERVE LAS SIGUIENTES PRECAUCIONES: 1. Use la unidad sólo de la manera indicada por el fabricante. Si tiene preguntas, comuníquese con el fabricante a la dirección o al número telefónico que seincluye...
Page 32 - OPERACIÓN; Controles; BOMBILLAS DE HALÓGENO; ADVERTENCIA: Siempre apague el; Afloje la tuerca anular girándola hacia la; PRECAUCIÓN: La bombilla puede; G-4 Base. ¡No toque la bombilla de reemplazo con las manos desnudas!
- 32 - OPERACIÓN Controles La campana se opera usando los controlesde deslizamiento que se encuentran debajode la parte inferior de la campana. El conmutador de la lámpara enciende yapaga las lámparas. El conmutador del ventilador enciende elventilador en uno de los siguientes ajustesde velocidad: 0...
Page 33 - REEMPLAZO DEL FUSIBLE; Eleve o quite el tubo de humos decorativo; MANTENIMIENTO
- 33 - REEMPLAZO DEL FUSIBLE SI LAS LÁMPARAS NO FUNCIONAN,D E S C O N E C T E L A E N E R G Í A E N L AENTRADA DEL SERVICIO. REVISE ELF U S I B L E Y R E E M P L Á C E L O S I E SNECESARIO. 1. Eleve o quite el tubo de humos decorativo inferior. 2. Quite la tapa de la caja de fusibles. 3. Desenrosque...
Page 34 - CONTINUACIÓN; Limpieza de la campana; Consejos útiles de limpieza:
- 34 - MANTENIMIENTO, CONTINUACIÓN Limpieza de la campana El acero inoxidable es unos de los materiales que se pueden mantener limpios conmás facilidad. Un cuidado ocasional ayudará a mantener su buen aspecto. Consejos útiles de limpieza: 1. Normalmente, todo lo que se necesita es agua caliente con ...
Page 35 - PREPARACIÓN DE LA CAMPANA; Desempaque la campana y revise el contenido del paquete.
- 35 - PREPARACIÓN DE LA CAMPANA Desempaque la campana y revise el contenido del paquete. Debe recibir: 1 - Campana1 - Conjunto del tubo de humos decorativo1 - Bolsa de piezas 1 - Soporte de montaje1 - Collar de la descarga1 - Soporte de montaje del tubo de humos8 - Tornillos de montaje (4.8 x 38 mm...
Page 36 - INSTALACIÓN ELÉCTRICA; ADVERTENCIA: Una o más personas
- 36 - INSTALACIÓN ELÉCTRICA ADVERTENCIA: Una o más personas calificadas deben realizar el trabajo decableado eléctrico, de acuerdo con todoslos códigos y normas correspondientes.E s t a c a m p a n a d e b e e s t a ra d e c u a d a m e n t e c o n e c t a d a a t i e r r a .I n t e r r u m p a l a...
Page 39 - MENOS Distancia sobre la
- 39 - PREPARACIÓN DE LA CAMPANA (SÓLO CAMPANAS PARA SISTEMAS SIN CONDUCTO)Nota: Se deben comprar los siguientes materiales para las instalaciones derecirculación sin conductos. Juego de recirculación sin conducto, Modelo RRK51Conducto de aluminio flexible / extensible de 5 pulg. (12.7 cm) de diámet...
Page 40 - INSTALACIÓN DE LA CAMPANA
- 40 - PREPARACIÓN DE LACAMPANA (CONTINUACIÓN) (SÓLO CAMPANAS PARA SISTEMAS SINCONDUCTO) 8. Deslice con cuidado la sección superior del tubo de humos decorativo en el interior de lasección inferior del tubo de humos decorativo. 9. Coloque con cuidado los tubos de humos decorativos en el área empotra...
Page 42 - LISTA DE PIEZAS DE RECAMBIO
Page 43 - PIEZAS DE REPUESTO; DESCRIPCIÓN
- 43 - PIEZAS DE REPUESTO MODELO RM53000 CLAVE N°. PIEZA N°. DESCRIPCIÓN 9 B08087294 1 4 B02300233 1 6 BE3346354 1 9 B03295005 2 6 B02300891 3 7 B02300787 4 5 BW0000019 4 8 B02310203 4 9 B03295076 5 3 B03202007 6 0 B02300249 6 2 B08091462 6 4 BE3347000 8 6 B08088378 113 B03202433 118 BE3347192 119 B...