NTI KEEMUX-P2 - Manuals - manualsarea.com

Page 2 - WARRANTY INFORMATION; COPYRIGHT

WARRANTY INFORMATION The warranty period on this product (parts and labor) is two (2) years from the date of purchase. Please contact Network Technologies Inc at (800) 742-8324 (800-RGB-TECH) in the US and Canada or (330) 562-7070 (worldwide) or at our website at http://www.networktechinc.com for in...

Page 3 - TABLE OF CONTENTS; INTRODUCTION; Available Options; MATERIALS; Materials Supplied with this kit:; OR

1 TABLE OF CONTENTS INTRODUCTION ............................................................................................................................................................................... 1 MATERIALS ..................................................................................

Page 4 - FEATURES AND FUNCTIONS; AUD 2; NTI; KEEMUX

2 FEATURES AND FUNCTIONS 1. CPU Status LEDs- for visual indication of connection between the user and a specific CPU. Also used for visual indication of switch mode status 2. CPU Select Switches- push to manually switch to a specific CPU 3. Remote- (optional) for connection of RMT-2-ST remote contro...

Page 5 - INSTALLATION; Male

3 INSTALLATION 1. Turn OFF power to all CPUs that will be connected to the NTI Switch before connecting or disconnecting any cables. WARNING! Damage to the CPU may result if power is not turned OFF before connecting or disconnecting cables. 2. Connect PS/2 keyboard to “USER KEYBD” port on the rear p...

Page 6 - Sequence; USING THE NTI SWITCH; Front Panel Control; Speakers

4 Units with audio support (optional) Connect the 3.5mm plug from speakers to the 3.5mm jack labeled "AUD OUT". Attach SA-xx-MM audio cables (purchased separately) between the audio port on each CPU and the 3.5mm audio jacks marked "AUD 1" on the KEEMUX switch. Be sure to connect the...

Page 7 - Keyboard Control; Press; COMMAND Mode; NOTE; Keystroke; SCAN Mode; I or; D or; Esc; or

5 Keyboard Control In order to control the switch with the keyboard, COMMAND Mode must be enabled. To enter/exit COMMAND Mode from the keyboard: Press COMMAND Mode When the COMMAND Mode is ON, all 3 status LEDs on the keyboard will illuminate to indicate that COMMAND Mode is enabled and the followin...

Page 8 - Keyboard Features; AUDIO SUPPORT; DUAL VIDEO SUPPORT; RS232 Connections and Configuration

6 Keyboard Features The keyboard configuration of each CPU is saved in the NTI Switch. For example, if the CPU attached to Port 2 had CAPS LOCK and NUM LOCK selected the last time that CPU was accessed, then they will automatically be set when that CPU is accessed again. AUDIO SUPPORT (Optional) Aud...

Page 9 - Dipswitches; UNIT ADDRESS

7 ON OFF 1 2 3 4 5 6 7 8 Dipswitches The dipswitches located next to the RS232 connection (Fig. 8) are used to configure the baud rate and address of the KEEMUX. The default baud rate is 9600. The default address is 1. Use the charts below to change the baud rate and address as needed. DIP SWITCH Th...

Page 10 - TECHNICAL SPECIFICATIONS; VGA Video

8 RS232 Interface Test Program RS232 communication is configured using the RMTEST program, located on the supplied floppy disk. This software allows a user to test the functions of an NTI KEEMUX or Multi-user/Multi-platform switch RS232 interface. The RMTEST program generates a main menu with the 3 ...

Page 11 - TROUBLESHOOTING

9 RS232 Port (DB-9 MALE) PIN SIGNAL FUNCTION 1 - No connection 2 RXD Receive data 3 TXD Transmit data 4 DTR Data terminal ready 5 GND Signal ground 6 DSR Data set ready 7 RTS Request to send 8 CTS Clear to send 9 - No connection REMOTE (RMT-2-ST) 5 DIN SIGNAL DESCRIPTION 1 LED1 TTL output, low = por...