Murphy CE-05171N - Manuals

CE-05171N page 6 of 44 3.0 Input/Output Types 3.1 Input/Output Types and Specifications for the Centurion C3-1 3.1.1 Digital Inputs (DI) Number of Devices: 32 Device Types: Discrete Input, Normally Open (N/O) or Normally Closed (N/C), active high/active low, non-incendive. There is one screw termina...

TTD-98055N page 9 of 44 3.1.6 Types and Specifications for the Optional Analog Output on the Centurion C3-1 -A Analog Outputs (AO) N Nu um mb be err o off D De ev viic ce es s:: 2 2 Device Types: Analog Output, (4 to 20) mA or (0-5)V, 16 bit hardware There are two screw terminal connectors for each ...

TTD-98055N page 10 of 44 3.2.2 Thermocouple Inputs (TC) N Nu um mb be err o off D De ev viic ce es s:: 8 8 Device Types: Thermocouple Input, Type J or K, 12 bit hardware Open Thermocouple Detection: Drives channel reading high (max of scale). There are two screw terminal connectors for each thermoco...

TTD-98055N page 11 of 44 5.0 Hardware Installation and Wiring 5.1 Mounting the Centurion Controller The Centurion can be mounted vertically or horizontally on a standard DIN rail. Three clamp type feet along the bottom of the controller attach to the DIN rail, however, rail stops are recommended to ...

CE-05171N page 16 of 44 HOME O Op pe erra attiin ng g S Stta attu us s S Sc crre ee en n Allows the user to get to the first line of the current screen, or if pressed again, to get to the default operating status screen. S Se ett U Up p S Sc crre ee en n Allows the user to get to the first line of t...

CE-05171N page 17 of 44 RUN/STOP O Op pe erra attiin ng g S Stta attu us s S Sc crre ee en n Initiate or cancel a start sequence. S Se ett U Up p S Sc crre ee en n No associated action in either Shutdown mode, or Remote mode on standby. Initiate stop sequence when held for two seconds, if equipment ...

CE-05171N page 18 of 44 ARROW RIGHT O Op pe erra attiin ng g S Stta attu us s S Sc crre ee en n Display next screen. Automatically repeats if held down continuously until reaching the final screen. S Se ett U Up p S Sc crre ee en n Display next screen. This key has no action when in a sub-menu. E Ed...

CE-05171N page 19 of 44 6 6..1 1..2 2 D Diis sp plla ay y C Co on ntte ex xtt The graphic LCD displays are organized around operating status screens and setup screens. The actual number of status screens will be related to the total number of end devices configured for the controller. In either scre...

CE-05171N page 20 of 44 6.2 Operational Screens In addition to the set up screens reviewed in Section 7.3, the C3-3 Display offers a number of operational displays. On the Operating Status screens, the two bottom lines display the state, hours, mode and active timer status. This information is key t...

CE-05171N page 23 of 44 6.3 Setup Screens and Menus 6 6..3 3..1 1 P Pa as ss sw wo orrd d S Sc crre ee en n Some settings are password protected, including the setup screens.This is the first screen seen when the SETUP/ENTER key is pressed. The password need only be entered once during any editingse...

CE-05171N page 38 of 44 Port 2 (USB) Interface: USB 1.1 Compliant Port capable of emulating RS232 communications via royalty free PC driver.Protocol/Services: Modbus (Slave), Proprietary (Binary)Connection: There is a USB Type B connector (see graphic).Automatic selection of USB is provided when a s...

CE-05171N page 41 of 44 7.3 Modbus Protocol The Centurion configurable controller was programmed with the Modbus protocol which is a system is based ona “master” and “slave” relationship. With Modbus protocol, the master and slave are able to continue to com-municate with each other through defined ...

CE-05171N page 44 of 44 Selecting a Centurion Configurable Controller C3 Series Model: 1. Specify one C3-1 Main I/O Module from Table A Model Specifications C3-1 no analog outputs C3-1-A two analog outputs 2. Specify one ( optional) C3-2 Expansion I/O Module 3. Specify one ( optional) C3-3 Display M...