Murphy PVA35 - Manual
Murphy PVA35 – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.
Table of Contents:
- Page 2 – PVA SERIES20 and PVA SERIES35 Dimensions and Mounting; BACK; HOLE CUTOUT; OR; OR; PVA35 Series Typical Installation and Mounting Dimensions; Deutsch DT
- Page 3 – PVA20, PVA35 and PVAA SERIES Typical Wirings For 12 and 24 VDC; PVA Gage; Place Resistor between RS485+ and RS485– at end; See Note; GRND; Place Resistor between RS485+ and RS485– at end; PVAA Audible Alarm Back View; SAH; Battery; See Note
- Page 4 – Typical Connectors PIN Designation; POWERVIEW; Typical Quick-Connect Diagram; Warranty
Description
The PowerView Analog Gages (PVA) are a series of intelligent gages
designed to display easy-to-read information transmitted by the PowerView.
The PVA gages communicate with the PowerView via a single RS485 twist-
ed pair MODBUS
®†
RTU serial link. The gages can be daisy-chained using
quick-connect harnesses with watertight connectors.
The PVA gages also include features such as a smooth stepper motor opera-
tion for the 270° sweep pointer, an environmentally sealed case with two
Deutsch DT style connectors molded into the casing, and green LED back
lighting. They are available for standard 2-1/16 in. (52 mm) and 3-3/8 in. (86
mm) diameter hole sizes. In addition their plastic cases incorporate a “D”
shape allowing panel cutouts that eliminate gage rotation during installation.
The PowerView Audible Alarm (PVAA) alerts operators to fault conditions
via piezoelectric alarm and relay contacts. It also has a temporary silencer
button that silences the audible tone for 2 minutes on alarms and 30 seconds
on shutdown conditions.
All PowerView Gages can be powered by 12 or 24 VDC systems.
PVA20 Series Models:
2 inch size gages:
PVA20 –A =
Engine Oil Pressure
PVA20 –B
=
Coolant Temperature
PVA20 –C
=
Voltmeter
PVA20 –D
=
Percent Load at Current RPM
PVA20 –E
=
Transmission Oil Pressure
PVA20 –F
=
Transmission Oil Temperature
PVA20 –G
=
Engine Oil Temperature
PVA20 –T
=
Tachometer
PVAA20
=
2 inch dial audible alarm gage
PVA35 Series Models:
3-1/2 in. size gages:
PVA35 –T
=
Tachometer
PVA35 –S
=
Speedometer
Specifications
Power Supply Input Voltage:
12/24V (8-32VDC min. & max. voltage).
Power Supply Operating Current:
(@ 14 VDC) =
PVA20, PVA35: 28 mA minimum; 52 mA maximum.
PVAA20: 19 mA minimum; 46 mA maximum.
Backlight Maximum Current
(not applicable to PVAA20): 24 mA.
Input:
RS485 MODBUS
®
RTU data.
Output:
Analog Readout.
Relay Rated Load (PVAA20):
0.5 A, 125 VAC; 1 A, 24 VDC.
Relay Maximum Switching Capacity (PVAA20):
62.5 VA, 30W.
External Audible Alarm Output (PVAA20):
28 VDC, 30 mA max. (cur-
rent sink).
Temporary Silence Button (PVAA20):
Charge transfer technology.
Operating Temperature:
-40° to 185°F (-40° to 85°C).
Storage Temperature:
-76° to 185°F (-60° to 85°C).
Dial:
White numerals over black background.
Indicating Pointer:
Stepper motor operation with 270° sweep.
Gage Accuracy:
PVA20: Better than ±1.0% of scale.
PVA35: Better than ±2% of scale.
Environmentally Sealed Enclosure:
Sealing:
IP68, ±5 psi (±34.4 kPA).
Case and Clamp Material:
Polyester (PBT).
Lens Material:
Polycarbonate.
Bezel Material:
Polyester (PBT).
Maximum Panel Thickness:
3/8 in. (9.6 mm).
Connectors:
6-Pin Deutsch DT06 Series.
†
MurphyLink is a registered trademark of FWMurphy. All other trademarks and
service marks used in this document are the property of their respective owners.
CAUTION:
These instruments are designed to be used ONLY
with the MurphyLink
TM
†
PowerView module or other approved
MurphyLink
TM
†
PowerView products.
Analog Gages PVA20
& PVA35 Installation Instructions
PVA-02126N
Revised 01-04
Section 78
00-02-0532
Please read the following information before installing
.
A visual inspection of this product for damage during ship-
ping is recommended before mounting. It is your responsibility to have a qualified person install this unit.
GENERAL INFORMATION
WARNING
BEFORE BEGINNING INSTALLATION OF THIS MURPHY PRODUCT
✔
Disconnect all electrical power to the machine.
✔
Make sure the machine cannot operate during installation.
✔
Follow all safety warnings of the machine manufacturer.
✔
Read and follow all installation instructions.
PVA20 Series
PVA35 Series
PVA-02126N page 1 of 4
"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.
Summary
PVA-02126N page 2 of 4 PVA SERIES20 and PVA SERIES35 Dimensions and Mounting Ø 2.324 in. (59 mm) 2.050 in. (52 mm) 0.48 in. (12 mm) 2.430 in. (62 mm) 1.956 in. (50 mm) 2 Push-on Type Plug Connectors Screw-on Type Mounting Clamp BACK FRONT Gray Area shows Domed lens style HOLE CUTOUT 1.972 in. (50 mm...
PVA-02126N page 3 of 4 PVA20, PVA35 and PVAA SERIES Typical Wirings For 12 and 24 VDC GRND GRND V+ V+ RS485 (+) Data RS485 (+) Data RS485 (-) Data RS485 (-) Data Pin 4 Pin 3 Pin 2 Pin 1 Pin 6 Pin 6 Pin 1 Pin 3 Pin 4 Pin 5 PVA Gage PV100 Note: Place Resistor between RS485+ and RS485– at end of Line o...
PVA-02126N page 4 of 4 Typical Connectors PIN Designation PowerView Gages Back View Deutsch DT06-6S Style Connections Recommended Connectors: Body: Deustch DT06-6SWedge Lock: W6STerminals: 0462-201-16141Sealing Plug: 114017 Plug A Plug B B A PIN 4 RS485 – PIN 3 RS485 + PIN 6 GRND PIN 1 V+ PIN 4 RS48...
