Mitsubishi P93DW- Manuals

2 2 PRECAUTIONS MAINTAIN GOOD VENTILATIONVentilation slots and holes are provided on sides of thisunit.Place the unit on a hard and level surface and locate atleast 4" (10cm) from walls to ensure proper ventilation. UNSUITABLE LOCATIONSAvoid shaky places or hot-springs areas where hydrogensulfid...

4 SAFETY TECHNICAL CHECKS Periods: According to the recommendations of the manufacturer of medical device.Scope: a) Visual check Housing, cables, operator controls, readout device ( displays, LED etc.), labels,accessories, instruction manual. b) Function test Performance check acc. instruction manua...

5 UNPACKING 3 1 1 1 1 1 Open the top of the box. 2 2 2 2 2 Remove the cushion above the unit. • Make sure to keep the unithorizontal. 3 3 3 3 3 Take the unit out of the box carefully. Take the unit out of the box by the following procedures. Make sure to check thecontents. 4 4 4 4 4 Unwrap the unit....

6 4 FEATURES AND FUNCTIONS OPEN COPY FEED LOCK UP DOWN BRT/CONT BRT CONT LOCK B 3 Front Panel 11 • 20 Power switch Turns on/off the power. 1 3 Function Name Reference Page 2 Displays stand-by, functions and errormessages. Indicator (BRT/CONT/LOCK) Displays the settings of brightness,contrast and but...

7 AC LINE ON OFF USB DIP SW 1 2 3 4 DIP SW FUNCTION TABLE NO. 1 2 3 4 FUNCTION LOCK SW-ON ON SW-OFF OFF Rear Panel POTENTIAL EQUALIZATION TERMINAL This is used to equalize the potential of theequipment connected to this unit.For details refer to the installationinstruction of equipment to beconnecte...

8 5 INSTALLATION OF PAPER Moisture, fingerprints or dust on thepaper surface may cause a noise atprinting or deterioration in printquality. Set the paper by the follow-ing procedure to prevent adhesionof fingerprint or dust on the papersurface. Note: The printing surface is the outside. Place the pa...

9 • Keep the high-density paper away from fingerprint, dust or moisture when storing it.• Do not touch the rubber roller. Do not stain or damage the roller surface.• Do not touch the thermal head (located behind the cutter). When printing, the thermal head is heated to high temperature. • Do not tou...

10 6 EXAMPLE OF CONNECTION / SETTING OF SWITCHES Connecting to various equipment with USB interface such asmedical equipment and personal computer. Connection Connect the digital monochrome printer with PC or medicalequipment through a USB cable. Setting of Switches Personal computer ormedical equip...

11 7 PRINTING Print a picture with an applicationsoftware. The image data is transferredthrough USB interface. FEED COPY cutter 2 You can set the number of copies by pressingthe COPY button on the front panel. (Settingrange : 1 to 200)You can copy the same picture as many timesas you desire until a ...

13 8 ADJUSTMENT OF PRINT PICTURE Adjustment of Printer Brightness/Printer Contrast You can make fine adjustment of printer brightness andprinter contrast of the printed picture. Control panel • For adjustment, use the BRT/CONT button " BRT/CONT ", UP button " UP " and DOWN button ...

15 Resetting the values You can reset the values of printer brightness and printercontrast. 1 Turn off the power. 2 While pressing the FEED button, turn on the power. 3 The display by the indicator changes from to , and the values are reset to the default setting. Automatic restoration to the standb...

16 9 In case of an error in the unit during operation, you are warnedby an alarm tone or the LED indicator. Cause/Error display 1 1 1 1 1 Overheat ERROR DISPLAY Symptom/Remedy [Symptom]• When the head gets overheated, the indicator blinks. When overheat occurs while more than one copy is being proc-...

17 Cause/Error display Cause/Error display 2 2 2 2 2 No paper [Symptom]• When the paper runs out or the paper is not installed, printing becomes impossible and an alarm tone is heard.In this case, all the buttons become invalid. • If this error occurs while more than one copy is being printed or the...

19 10 STATUS AND MODES Set state/Mode LED display Contents of LED display Power off Stand-by Print state Printer brightness mode Printer contrast mode Error detect state Power off During data receiving During data receiving Fine adjustment of the picture brightness No paper Button input error Door i...

20 11 When the thermal head is dirty with dust, etc., white spots or stripes may appear on theprint. In this case, clean the thermal head by the following procedure BY USING THESUPPLIED CLEANING PAPER. Roll the cleaning paper and installinto the set. Switch the left side lever to the OPENposition.Th...

21 12 MAINTENANCE Turn off the power for maintenance. Maintenance of Main Unit Wipe off stains of the front panel with a soft cloth.When the panel is heavily stained, wipe with a cloth moistenedwith neutral cleanser diluted by water and finish with a drycloth. Maintenance of Rubber Roller When the r...

22 13 SPECIFICATIONS Type: Digital Monochrome Printer Model: P93DW/P93DE Power supply andpower consumption: 100-240V AC, 50/60Hz, 1.5 - 0.8A Connection terminal: USB interface (Series "B" receptacle)Hi-Speed USB (Ver. 2.0) supported Resolution: 1280 x 1280 pixels (Standard)(Max. 1280 x 5760 ...