Mitsubishi MCCH1- Manuals

Page 2 - Wireless System Installation Guide; Install batteries in wireless devices; Remote Controller; lithium; Push the excess cable back through the indoor

Wireless System Installation Guide 69-2426—01 2 M28474 1 Install batteries in wireless devices Install batteries in all devices. Make sure batteries are inserted properly (see polarity marks on the devices). 2 Install cable and receiver M28472A Remote Controller Portable Central Controller (optional...

Page 3 - Link all devices to wireless network; CONNECT; Link remote controller to wireless network; NEXT

3 69-2426—01 3 Link all devices to wireless network 1 Remove cover from wireless receiver. 2 Verify POWER light is solid green. 3 Press and release the CONNECT button. 4 If CONNECT light does not flash, another receiver or RedLINK wireless adapter may be in wireless setup mode. Exit wireless setup a...

Page 4 - Link Portable Central Controller to RedLINKTM network (optional); WIRELESS SETUP

Wireless System Installation Guide 69-2426—01 4 Link Portable Central Controller to RedLINK™ network (optional) Link outdoor sensor to RedLINK™ network (optional) CONNECT WIRELESS SETUP M28481 M28483 NO YES CONNECT MORE? M28482 1 Make sure the CONNECT light on the wireless receiver is flashing. 2 Pr...

Page 5 - Exit wireless setup; Customize remote controller (installer setup)

5 69-2426—01 Exit wireless setup 4 Customize remote controller (installer setup) Press and release the CONNECT button at the wireless receiver to exit wireless setup (light should stop flashing and remain solid). Replace cover on wireless receiver. Follow the steps below to begin installer setup. At...

Page 6 - Installer setup tables; Setup function

Wireless System Installation Guide 69-2426—01 6 Installer setup tables Setup function Settings & options (factory default in bold) 101 Unit automatically restarts after power outage 1 OFF 2 ON 3 Not Supported 103 Ventilation Air 1 Not Supported 2 IDU does not intake outdoor air through LOSSNAY 3...

Page 9 - Follow the procedure below to test for proper operation.; System test; Commercial Override; to temporarily activate an occupied temperature. Each press of; Optimal Start

9 69-2426—01 Special functions Installer test Follow the procedure below to test for proper operation. M28488A To begin, press and hold the s and t buttons until the display changes (about 3 seconds). Press s or t to check system status Press NEXT to advance to next test Press DONE to terminate syst...

Page 10 - Mount remote controller & outdoor sensor; Place sensor securely; RedLINKTM error codes

Wireless System Installation Guide 69-2426—01 10 Outdoor sensor (optional) 5 Mount remote controller & outdoor sensor 1 Separate the wallplate from the remote controller. 2 Mount the wallplate using the included screws and anchors 5 feet from the floor on an interior wall. If the remote controll...

Page 11 - Replacing system components; follow the procedures on page 4 to link it to the wireless network.; Wireless receiver; At the remote controller:; FAN; At the Portable Central Controller:; REMOVE

11 69-2426—01 Replacing system components Note: Only use Mitsubishi Electric components or other designated components for installation. Failure to comply may damage the product or cause a hazardous condition. Remote Controller To replace a remote controller, install batteries and follow the procedu...

Page 12 - Regulatory information; Specifications & replacement parts; Operating Ambient Temperature; Operating Relative Humidity; Physical Dimensions; Accessories & Replacement Parts

© 2010 Mitsubishi Electric & Electronics USA, Inc.Suwanee, GA 30024 All Rights Reserved.The three diamond logo is a registered trademarkof Mitsubishi Electric Corporation 69-2426—01 M.S. 11-10Printed in U.S.A. Regulatory information FCC Compliance Statement (Part 15.19) (USA only) This device co...

Manuals:

Installation Manual Mitsubishi MCCH1

Summary

Mitsubishi Manuals