Mitsubishi M800- Manuals

Page 2 - MoTeC; Description

MoTeC Pty Ltd DVIN0004 M800OEM - EVO47 and 8RS Page 2 of 16 document. The other version uses an ECU with a three plug main connector which is supported by the EVO8 or EVO89 OEM adaptor and installation notes (MoTeC Part Numbers 13007A – EVO8, 13010A – EVO89). There are differences with these applica...

Page 3 - Overrun Fuel Cut

MoTeC Pty Ltd DVIN0004 M800OEM - EVO47 and 8RS Page 3 of 16 Model Specific Information EVO8 RS Mitsubishi has released two versions of the EVO8. One version uses a new ECU with a three plug main connector. This vehicle is supported by the EVO8 OEM adaptor. There is also a version which uses an ECU w...

Page 4 - Additional Sensors; Spare input; Using an external thermocouple amplifier (TCA)

MoTeC Pty Ltd DVIN0004 M800OEM - EVO47 and 8RS Page 4 of 16 Additional Sensors It is possible to use un-assigned pins for additional sensors. The availability of spare inputs will vary depending on the model of car, refer to the table below and the M800 Pinout for details. There are also spare 5v 8v...

Page 5 - Power

MoTeC Pty Ltd DVIN0004 M800OEM - EVO47 and 8RS Page 5 of 16 M800 Pinout Plug B59 Yellow Plug B60 Yellow Plug B61 Yellow Plug B62 Yellow 2 15 3 16 4 17 5 18 1 14 6 19 7 20 8 21 9 22 10 23 11 24 12 25 13 26 57 58 59 60 61 62 51 52 53 54 55 56 43 44 45 46 42 31 32 33 34 35 36 39 37 40 38 41 92 71 72 73...

Page 9 - Inputs

MoTeC Pty Ltd DVIN0004 M800OEM - EVO47 and 8RS Page 9 of 16 M800 Pin OEM Pin No. Standard Function Optional Function Setup Notes Inputs REF 89 Ref Sensor (Hall) SYNC 88 Sync Sensor (Hall) AT1 72 Air temperature (AFM Pin2) Calibration: 1 AT2 83 Engine Temp Calibration: 1 AT3 82 Ignition Switch Functi...

Page 11 - Communications

MoTeC Pty Ltd DVIN0004 M800OEM - EVO47 and 8RS Page 11 of 16 M800 Pin OEM Pin No. Standard Function Optional Function Setup Notes LA1P 75 #75 Use if vehicle wiring is being modified to use a wide band lambda sensor – Connect shield wire to Pin75. LA2S Wide band lambda using internal Lambda 2 connect...

Page 12 - OEM ECU Pinout

MoTeC Pty Ltd DVIN0004 M800OEM - EVO47 and 8RS Page 12 of 16 OEM ECU Pinout Plug B59 Yellow Plug B60 Yellow Plug B61 Yellow Plug B62 Yellow 2 15 3 16 4 17 5 18 1 14 6 19 7 20 8 21 9 22 10 23 11 24 12 25 13 26 57 58 59 60 61 62 51 52 53 54 55 56 43 44 45 46 42 31 32 33 34 35 36 39 37 40 38 41 92 71 7...

Page 14 - Calibration Tables; Parameter Value; Injector Battery Comp

MoTeC Pty Ltd DVIN0004 M800OEM - EVO47 and 8RS Page 14 of 16 Calibration Tables Mass Air Flow Sensor DIG2 g/s 1 decimal place Input (Hz) 0.0 10.0 g/s 0.0 3.3 Setup Parameter Value Notes Injector Current 0.0 Injector Battery Comp 4 See Injector Battery Comp Table Peak and hold ratio 4 Eff Calc Method...

Page 15 - Link Table; Open Links

MoTeC Pty Ltd DVIN0004 M800OEM - EVO47 and 8RS Page 15 of 16 Link Table Open Links Closed Links Function 01, 15 26 • AUX1 Lambda heater 01, 26 15 AUX1 ECU Power Control 15, 26 01 AUX1 Fuel Pressure VSV 14, 19 21, 24 •INJ6 Spray bar Control (7) 19, 21, 24 14 INJ6 Fuel Pump Speed 14, 21, 24 19 INJ6 Sh...

Page 16 - Pressure kPa; Lambda 2 Connector; Function; Comms Connector; OEM

MoTeC Pty Ltd DVIN0004 M800OEM - EVO47 and 8RS Page 16 of 16 On-board BAP sensor calibration – AV4 , Calibration = 62 Pressure kPa Vout (V) M800 AD counts 15 0.2 54 115 4.8 1284 Lambda 2 Connector 2 3 4 5 1 6 Looking at pins on male plug (into connector) OEM M800 Function La2-1 LA2-P La2 header – Pu...

Manuals:

User Manual Mitsubishi M800

Summary

Mitsubishi Manuals