Minolta 5430 - Manuals - manualsarea.com

Page 2 - MINOLTA; u n i n e t

UNINET IMAGING INC . • MINOLTA ® MAGICOLOR 5430 CARTRIDGE REMANUFACTURING INSTRUCTIONS MINOLTA ® MAGICOLOR 5430 TONER CARTRIDGE SIDE VIEW WITH END CAP SHOWN BACK VIEW OPPOSITE SIDE VIEW © 2007 UniNet Imaging Inc. All Trademark names are property of their respective owners. Product brand names mentio...

Page 3 - SEPARATING THE CARTRIDGE

UNINET IMAGING INC . • MINOLTA ® MAGICOLOR 5430 CARTRIDGE REMANUFACTURING INSTRUCTIONS SEPARATING THE CARTRIDGE 1. Locate the cartridge end cap of the cartridge. Using a phillips screwdriver, remove the seven highlightedscrews that hold the cartridge together. 2. Cartridge separated. Set the drum un...

Page 4 - SEPARATING THE DRUM UNIT

UNINET IMAGING INC . • MINOLTA ® MAGICOLOR 5430 CARTRIDGE REMANUFACTURING INSTRUCTIONS SEPARATING THE DRUM UNIT 5. The drum unit (top) and developer unit (bottom) are joinedtogether. 6. Locate the gear train side of the drum unit. Remove the OPC contact (highlighted). Now remove the gear train direc...

Page 5 - Locate the developer roller drive gear just below the OPC.

UNINET IMAGING INC . • MINOLTA ® MAGICOLOR 5430 CARTRIDGE REMANUFACTURING INSTRUCTIONS 9. Release the compression spring on the opposite side of thedrum unit (drive gear side). Note: The compression springs are different, the longer spring isconnected to the gear train side of the drum and the small...

Page 6 - DISASSEMBLING THE DRUM UNIT

UNINET IMAGING INC . • MINOLTA ® MAGICOLOR 5430 CARTRIDGE REMANUFACTURING INSTRUCTIONS 15. Once the screw has been removed, turn the support counterclockwise until it comes to a stop. This will unlock the supportand allow you to remove it completely. 16. Final position of drive gear support plate th...

Page 7 - REMOVING THE CORONA WIRE ASSEMBLY

UNINET IMAGING INC . • MINOLTA ® MAGICOLOR 5430 CARTRIDGE REMANUFACTURING INSTRUCTIONS REMOVING THE CORONA WIRE ASSEMBLY 19. Remove the corona wire by pushing it towards the openingon the gear train side. This will allow you to lift one side of it foreasy removal. 20. Corona wire assembly removed. R...

Page 8 - Remove the wiper blade in the manner shown.

UNINET IMAGING INC . • MINOLTA ® MAGICOLOR 5430 CARTRIDGE REMANUFACTURING INSTRUCTIONS 22. Remove the wiper blade in the manner shown. CLEANING THE WASTE HOPPER 23. Hopper shown with wiper blade completely removed. Dump the waste toner from the hopper and clean thoroughlyusing compressed air. Clean ...

Page 9 - INSTALLING THE OPC

UNINET IMAGING INC . • MINOLTA ® MAGICOLOR 5430 CARTRIDGE REMANUFACTURING INSTRUCTIONS 25. Once the corona wire is aligned with the cartridge, Push itwith your finger tips until it is back into its original place. INSTALLING THE OPC 26. Before inserting the OPC, make sure its gears are facing inthe ...

Page 10 - Assemble the two halves by first inserting the drive gear.

UNINET IMAGING INC . • MINOLTA ® MAGICOLOR 5430 CARTRIDGE REMANUFACTURING INSTRUCTIONS 29. Assemble the two halves by first inserting the drive gear. 30. Once that has been accomplished join the two halves andinsert the pin on the gear train side. 31. Install the developer roller drive gear and its ...

Page 11 - REMOVING THE OEM CHIP; BEFORE

UNINET IMAGING INC . • MINOLTA ® MAGICOLOR 5430 CARTRIDGE REMANUFACTURING INSTRUCTIONS 33. Once the two halves are assembled, continue installing the gear train and springs as shown. REMOVING THE OEM CHIP 34. Locate the OEM chip on the inner portion of the end cap(shown). The chip has been fastened ...

Page 12 - ASSEMBLING THE END CAP

UNINET IMAGING INC . • MINOLTA ® MAGICOLOR 5430 CARTRIDGE REMANUFACTURING INSTRUCTIONS 36. Aftermarket chip installed. 37. Install the drum contact as shown. ASSEMBLING THE END CAP 38. Once the chip has been installed, you can proceed withinstalling the inner section of the end cap. 39. Install the ...

Page 13 - Secure the end cap with the seven screws.

UNINET IMAGING INC . • MINOLTA ® MAGICOLOR 5430 CARTRIDGE REMANUFACTURING INSTRUCTIONS 40. Install the outer end cap. 41. Secure the end cap with the seven screws. NOTES © 2007 UniNet Imaging Inc. All Trademark names are property of their respective owners. Product brand names mentioned are intended...