Miller Cool Belt- Manuals

Page 2 - U s e r I n s t r u c t i o n s - E n g l i s h; DualTech; Webbing; Miller Revolution Key Features

U s e r I n s t r u c t i o n s - E n g l i s h 2 Thank you for purchasing the Miller Revolution Harness. The Revolution is an all new and totally innovative harness engineered with seven (7) unique components and more than eleven (11) key product features. Your Miller Revolution harness was enginee...

Page 4 - Donning the Revolution without Belt

U s e r I n s t r u c t i o n s - E n g l i s h 4 Hold harness by back D-ring. Shake harness to allow all straps to fall in place. If leg or chest straps are buckled, release straps and unbuckle at this time. Slip straps over shoulders so D-ring is located in the middle of the back between shoulder ...

Page 5 - Donning the Revolution with Belt

U s e r I n s t r u c t i o n s - E n g l i s h 5 Hold harness by back D-ring. Shake harness to allow all straps to fall in place. If leg or chest straps are buckled, release straps and unbuckle at this time. Slip straps over shoulders so D-ring is located in the middle of the back between shoulder ...

Page 6 - Steps for Ensuring a Snug Fit; Adjusting Back D-Ring Pad; Adjusting Cam Buckles

U s e r I n s t r u c t i o n s - E n g l i s h 6 Steps for Ensuring a Snug Fit Adjusting Back D-Ring Pad The upper part D-ring pad (gray mesh) should be located approximately one (1) inch below the neckline. (This should position the back D-ring in between the lower part of the shoulder blades.) Co...

Page 7 - Installing Optional Accessories; Connecting Accessories; The combined weight of the harness user, and all attached

U s e r I n s t r u c t i o n s - E n g l i s h 7 Installing Optional Accessories /RFDWHWKH¿JXUH “8” shaped com-posite attachment clip on the back of the accessory. Identify the green button attachment point on the belt or harness that will be used. Place the widest end of WKH¿JXUH³´ over the green ...

Page 8 - Optional Shoulder Pads; Installing Shoulder Pads

U s e r I n s t r u c t i o n s - E n g l i s h 8 Turn the harness, so that the D-ring is laying up on a flat surface. Take one of the shoulder pads and place your finger over the Velcro ® . Lift up the webbing shoulder strap and carefully slide the Velcro portion of the shoulder pad into the pocket...

Page 9 - Optional Seat Pad; Installing a Seat Pad; Installing Seat Pad

U s e r I n s t r u c t i o n s - E n g l i s h 9 Make sure the flat side of the seat pad is facing towards the back of the harness, then at-tatch the two snap straps in the middle of the butt strap. Next, thread the front snap retaining straps at the front of the pad over the leg strap, under the b...

Page 10 - Available Accessories

U s e r I n s t r u c t i o n s - E n g l i s h 10 2 Pocket Nail & Tool Pouch Open End Pliers & Tool Holder Zippered Cylindrical Utility Pouch Multi-pouch Tool Bag Hammer Holder Water Bottle Holder Open Bolt and Bull Pin Bags Cell Phone Holders (two sizes) For more information or to purchase...

Page 11 - Materials; DWHULDOV6SHFL¿FWRWKH5HYROXWLRQ+DUQHVV

U s e r I n s t r u c t i o n s - E n g l i s h 11 Materials 0DWHULDOV6SHFL¿FWRWKH5HYROXWLRQ+DUQHVV PivotLink: Aluminum, Polyproplyene, Stainless Steel TechWeb: Polyester, Nylon Label Pack: Polyproplyene, Santoprene Pads (Belt, Shoulder, Back): Polyester, Nylon Stand-up D-Ring Assembly: Steel, Stain...