Miller 3000-4AH - Manuals - manualsarea.com

Page 2 - From Miller to You

Miller Electric manufactures a full lineof welders and welding related equipment.For information on other quality Millerproducts, contact your local Miller distributorto receive the latest full line catalog orindividual catalog sheets. To locate your nearestdistributor or service agency call 1-800-4...

Page 5 - TABLE OF CONTENTS

safety_trailer 10/96 LOOSE OR INCORRECT HARDWARE ANDFASTENERS can cause injury and damage. 1. Periodically double-check all nuts and bolts for tightness and condition. 2. If necessary, always replace any fastener with one of equal size, grade, and type. 3. Be sure the grade marks on replacement fast...

Page 7 - NOTE; CAUTION; SECTION 2 – SPECIFICATIONS

OM-659 Page 1 SECTION 1 – SAFETY INFORMATION mod1.1 2/93 Read all safety messages throughout this manual. Obey all safety messages to avoid injury. Learn the meaning of WARNING and CAUTION. 1 Safety Alert Symbol 2 Signal Word WARNING means possible deathor serious injury can happen. CAUTION means po...

Page 8 - SECTION 3 – INSTALLATION & OPERATION; Operating Parking Brake And Jack

OM-659 Page 2 ST-148 258 Inches Millimeters A 20 508 B 13 330 C 48-1/2 1232 D 74 1879 E* 158-1/2 4026 *150 in (3810 mm) Without Optional Hitch A B C D E Dimensions A and B will decreasewhen weight is added to trailer. Figure 2-1. Overall Dimensions SECTION 3 – INSTALLATION & OPERATION All direct...

Page 9 - Installing Fenders And Lights

OM-659 Page 3 3-2. Installing Fenders And Lights WARNING TILTING OF TRAILER can result in personal injury or equipment damage. • Use adequate blocks or lifting device to support hitch end while pivoting trailer jack into position (see Section 3-1). • Use trailer jack to obtain desired height and to ...

Page 10 - Installing Optional Tool Box

OM-659 Page 4 1 Connector 2 Run Wire 3 Tap Wire Place unstripped run wire in slottedchannel. Insert unstripped tap wire into otherchannel until it hits internal stop. 4 Contact 5 9 Inch Linemans Pliers Use pliers to push contact downflush with top of connector. Close top cover. Ref. S-0448 1 2 3 4 5...

Page 11 - Installing Optional Cylinder Rack And Shielding Gas Cylinders

OM-659 Page 5 3-4. Installing Optional Cylinder Rack And Shielding Gas Cylinders WARNING CYLINDERS can explode if damaged. • Keep cylinders away from welding and otherelectrical circuits. • Never touch cylinder with welding electrode. • Always secure cylinder to running gear, wall, orother stationar...

Page 13 - Installing Welding Generator

OM-659 Page 7 3-6. Installing Welding Generator WARNING FALLING EQUIPMENT can causeserious personal injury and equipmentdamage. • Use lifting eye to lift unit only, NOT running gear, gascylinders, trailer, or any other heavy options,accessories, or devices. • Use equipment of adequate capacity to li...

Page 14 - Maintenance

OM-659 Page 8 3-7. Maintenance WARNING FALLING EQUIPMENT can cause serious personal injury and equipment damage. • Apply parking brake while performing maintenance (see Section 3-1). • Support trailer with jack, or use proper equipment to lift trailer. • Do not put any body part under trailer while ...

Page 15 - Torquing Wheel Bearings

OM-659 Page 9 3-8. Torquing Wheel Bearings FALLING EQUIPMENT can causeserious personal injury and equipmentdamage. • Use equipment of adequate capacity to lift unit. • Do not put any body part under unit while lifting orworking on bearings. INCORRECT BEARING MAINTENANCEcan cause loss of control resu...

Page 16 - SECTION 4 – PARTS LIST

OM-659 Page 10 SECTION 4 – PARTS LIST 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 21 22 23 24 25 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 40 46 47 Figure 4-1. Complete Assembly ST-147 524-D 20 26 . Hardware is common andnot available unless listed.

Page 19 - (Equipment with a serial number preface of “LA” or newer)

Warranty Questions? Call1-800-4-A-MILLERfor your localMiller distributor. miller_warr 7/00 Your distributor also givesyou ... ServiceYou always get the fast,reliable response youneed. Most replacementparts can be in yourhands in 24 hours. SupportNeed fast answers to thetough welding questions?Contac...

Page 20 - Please complete and retain with your personal records.; For Service

PRINTED IN USA  2000 Miller Electric Mfg. Co. 6/00 Miller Electric Mfg. Co. An Illinois Tool Works Company1635 West Spencer StreetAppleton, WI 54914 USA International Headquarters–USAUSA Phone: 920-735-4505 Auto-AttendedUSA & Canada FAX: 920-735-4134International FAX: 920-735-4125 European Head...