Microsoft SHG-VS - Manuals - manualsarea.com

Page 2 - Contents; CONTENTS

Newall Measurement Systems Contents 1 CONTENTS 1.0 Technical Specification ..............................................1 1.1 Bracketry ..............................................................................2 1.2 Preparation ......................................................................

Page 3 - Introduction; Bracketry; Warnings

Introduction Newall Measurement Systems 2 1.0 INTRODUCTION This manual will provide connection and mounting instructions for Newall's Absolute, Digital and DistanceCoded linear encoders. It is important that you read and understand this manual prior to commencing thehardware installation. Electronic...

Page 4 - Item; Encoder Assembly / Mounting the Reader Head; MOUNTING THE READER HEAD

Figure 3.1 - Alignment of the reader head 2.0 ENCODER ASSEMBLY Item Description 1 Reader Head 2 Scale 3 Scale Support Link 4 Scale Anchor Pin 5 Support Pillar Short Item Description 6 Support Pillar Long 7 Scale Cover 8 M5 Nut 9 M8 x Socket Button Head Newall Measurement Systems 3 Encoder Assembly /...

Page 5 - Mounting the Scale; MOUNTING THE SCALE; Double End Mounting

Mounting the Scale Newall Measurement Systems 4 4.0 MOUNTING THE SCALE 4.1 Double End Mounting Note: Refer to section 4.3 for mounting scales in excess of 2.5 metres. Each end of the scale is different and can be identified by the “calibration adjustment end” and the “fixed end. NOTES: (A) Erroneous...

Page 7 - Single End Mounting

Mounting the Scale Newall Measurement Systems 6 Remove the link/pin assembly and the scale from the reader head. Drill and tap M8 x 18mm deep (USA 5/16" -18 x 3/4"deep) into the machine casting as marked by the transfer punch. Fit the pillar(s) to the machine casting by using one ofthe metho...

Page 10 - Mounting the Scale / Fitting the Scale Guard; FITTING THE SCALE GUARD

Mounting the Scale / Fitting the Scale Guard Length 2500mm 3000mm 3500mm 4000mm 4500mm 5000mm 5500mm 6000mm 6500mm 7000mm 7500mm 8000mm 8500mm 9000mm 9500mm 10000mm 10500mm 11000mm No. of Scale Supports 2 2 2 2 3 3 3 3 4 4 4 4 5 5 5 6 6 6 Left Side (A) 850mm 1100mm 1350mm 1500mm 1125mm 1250mm 1350mm...

Page 11 - Cable Routing / Final Check

Newall Measurement Systems 10 Cable Routing / Final Check 6.0 CABLE ROUTING The most important and the most over looked aspect of fitting the linear encoder is proper cable routing. Dangling andloose cables can be snagged or broken causing irreparable damage. Care should be taken in order to ensure ...

Page 12 - Appendix A - SCALE BRACKET MOUNTING OPTIONS; Outboard scale support mounting

Appendix A Newall Measurement Systems 11 Appendix A - SCALE BRACKET MOUNTING OPTIONS Outboard scale support mounting Scale supports inverted

Page 13 - Appendix B; Appendix B - DIMENSIONAL DRAWING

Appendix B Newall Measurement Systems 12 Appendix B - DIMENSIONAL DRAWING

Page 15 - Notes

Page 16 - NEWALL MEASUREMENT SYSTEMS LTD; Oct

NEWALL MEASUREMENT SYSTEMS LTD 023-80620 /03 -UK . Oct 2006 HEAD OFFICE Newall Measurement Systems Ltd. Technology Gateway, Cornwall Road South Wigston Leicester LE18 4XH United Kingdom Telephone: +44 (0)116 264 2730 Facsimile: +44 (0)116 264 2731 Email: [email protected] Web: www.newall.co.uk Newa...